Hitachi WJ200-001S Instruction Manual page 679

Index− − − − 6
Q
Quick start enable.............................. 4-42
R
Ratings lebel ....................................... 1-3
Reactance ........................................... A-6
Recommended ferrule .......................... 4-9
Rectifier .............................................. A-6
Reduce torque ................................... 3-22
Regenerative braking ........................... A-6
Regulation ........................................... A-6
Relay
alarm signal contacts ................... 4-59
as inteligent output ...................... 4-52
Remote control .................................. 4-33
up function(motorized speed
pot) .............................................. 4-34
down function
(motorized speed pot) .................. 4-34
datA clear ..................................... 4-34
Reset
function ..................................... 3-102
inverter ....................................... 4-29
Restart Mode configuration ................ 3-72
Restarting simple positioning ....... Ver.3-11
Retain output frequency ..................... 4-49
Revision history .................................. xviii
Reverse
roration ....................................... 4-81
run/stop ...................................... 4-16
run protection .............................. 3-55
torque ........................................... A-6
RF noisefilter ....................................... 5-4
Rotor ................................................... A-6
Rotation
direction detection ....................... 4-50
direction restriction ...................... 3-55
restriction related
paramerter ............................. 3-55
RPM .................................................. 2-36
Run
command .................................... 4-11
command source ......................... 4-84
command source setting2-30,3-12,4-35
mode .................................... 2-34,3-4
power on waring time ................... 3-55
signal .......................................... 4-52
source monitor ........................ Ver.3-3
time expiration signal ................... 4-64
Running the motor ............................. 2-34
Run time edits ......................3-4,3-53,4-27
S
Safety
how it work .................................... E-2
Installtion ...................................... E-2
massage ........................................... I
precaution ..................................... E-3
related signals ............................ 4-49
Safe stop function ............... 4-92,Ver.3.1-4
Saturation voltagel .............................. A-6
Scaling.............................................. 3-70
S-curve accel/deccel ......................... 3-38
Second
accel and deccel ......................... 3-37
motor .......................................... 4-21
stage output ................................ 4-71
nd
motor selection .......................... 4-85
２
Sensorless vector control .... 3-22,3-107,A-6
Service warranty ............................... 6-22
Set (select)2nd motor data ................. 4-21
Setpoint .............................................. A-7
Simple positioning ............................ 3-114
current position store .............. Ver.3-16
preset function by PSET ......... Ver.3-16
settings ....................................... 3-116
&Brake control co-operation .... Ver.3-14
Single-phase power ............................. A-7
Single phase pulse input ...........................
3-114,3-115,Ver.3.1-3
Sink/source input configuration .......... 4-12
Slip
definition ....................................... A-7
compensation gain ...................... 3-24
Software lock ....................... 3-4,3-53,4-27
Specifications
control logic signals ............... 1-10,4-6
general ......................................... 1-8
inveter .......................................... 1-4
inverter label ................................. 1-3
Speed
command ..................................... 2-29
control .......................... 1-18,1-22,4-17
detection.................... Ver.3-3,Ver.3.1-3
deviation excessive signal ............ 4-68
position changeover ..................... 4-48
position switching function ...........3-120
pot ............................................... 2-25
Squirrel cage ....................................... A-7
Standard functions ............................. 3-12
Start
frequency adjustment .................. 3-70
contact signal .............................. 4-77
motor ........................................... 4-31
Stator .................................................. A-7
STO(Safe Torque Off)
performance monitor
(output terminal 11 only) ............... 4-86
settings ....................................... 3-79
Stop
enable function ........................... 3-70
mode configuration ...................... 3-72
motor .......................................... 4-31
Store new register data
(enter command) ...................... B-19
Supply wiring .................................... 2-16
Support of multiple pole ................. Ver.3-7
Symbol definitions ................................... i
System description .............................. 2-4