Hitachi WJ200-001S Instruction Manual page 498

Option Terminal
Function Name
Code Symbol
 PID PID Disable
 PIDC PID Reset
Remote Control UP
 UP Function (motorized
speed pot.)
Remote Control Down
 DWN Function (motorized
speed pot.)
Remote Control Data
 UDC
Clearing
 OPE Operator Control
Multi-speed Select,
 SF1
Bit operation Bit 1
Multi-speed Select,
 SF2
Bit operation Bit 2
Multi-speed Select,
 SF3
Bit operation Bit 3
Multi-speed Select,
 SF4
Bit operation Bit 4
Multi-speed Select,
 SF5
Bit operation Bit 5
Multi-speed Select,
 SF6
Bit operation Bit 6
Multi-speed Select,
 SF7
Bit operation Bit 7
Overload Restriction
 OLR
Source Changeover
 TL Torque Limit Selection
 TRQ1 Torque limit switch 1
 TRQ2 Torque limit switch 2
Option Terminal
Function Name
Code Symbol
 BOK Brake confirmation
 LAC LAD cancellation
 PCLR Pulse counter clear
 ADD ADD frequency enable
Input Function Summary Table
Selects the direction of motor rotation: OFF = REV. While
OFF the motor is rotating, a change of F/R will start a
deceleration, followed by a change in direction
Temporarily disables PID loop control. Inverter output turns
ON
OFF as long as PID Enable is active (=)
Has no effect on PID loop operation, which operates
OFF
normally if PID Enable is active (=)
Resets the PID loop controller. The main consequence is that
ON
the integrator sum is forced to zero
OFF No effect on PID controller
Accelerates (increases output frequency) motor from current
ON
frequency
OFF Output to motor operates normally
Decelerates (decreases output frequency) motor from current
ON
frequency
OFF Output to motor operates normally
Clears the UP/DWN frequency memory by forcing it to equal
ON the set frequency parameter F001. Setting  must be
set= to enable this function to work
OFF UP/DWN frequency memory is not changed
Forces the source of the output frequency setting  and
ON the source of the Run command  to be from the digital
operator
Source of output frequency set by  and source of Run
OFF
command set by  is used
ON Bit encoded speed select, Bit 1, logical 1
OFF Bit encoded speed select, Bit 1, logical 0
ON Bit encoded speed select, Bit 2, logical 1
OFF Bit encoded speed select, Bit 2, logical 0
ON Bit encoded speed select, Bit 3, logical 1
OFF Bit encoded speed select, Bit 3, logical 0
ON Bit encoded speed select, Bit 4, logical 1
OFF Bit encoded speed select, Bit 4, logical 0
ON Bit encoded speed select, Bit 5, logical 1
OFF Bit encoded speed select, Bit 5, logical 0
ON Bit encoded speed select, Bit 6, logical 1
OFF Bit encoded speed select, Bit 6, logical 0
ON Bit encoded speed select, Bit 7, logical 1
OFF Bit encoded speed select, Bit 7, logical 0
ON Perform overload restriction
OFF Normal operation
ON Setting of  is enabled
OFF Max. torque is limited with 200%
ON
Torque limit related parameters of Powering/regen, and
OFF
FW/RV modes are selected by the combinations of these
ON
inputs.
OFF
Input Function Summary Table
ON
Brake wait time () is valid
OFF
Brake wait time () is not valid
Set ramp times are ignored. Inverter output immediately
ON
follows the freq. command.
OFF Accel. and/or decel. is according to the set ramp time
ON Clear the position deviation data
OFF Maintain the position deviation data
ON Adds the  (add frequency) value to the output frequency
OFF Does not add the  value to the output frequency
Description
Description
Ver.269