Hitachi WJ200-001S Instruction Manual page 650

I I I I nput Function S nput Function Su u u u mmary Table mmary Table – This table shows all thirty-one intelligent input functions at a glance.
nput Function S nput Function S mmary Table mmary Table
Detailed description of these functions, related parameters and settings, and example wiring diagrams
are in "Using Intelligent Input Terminals" on page 30.
O O O O ption ption ption ption T T T T erminal erminal erminal erminal
F F F F unction Name unction Name unction Name unction Name
C C C C ode ode ode ode S S S S ymbol ymbol ymbol ymbol
00 00
00 00
FW FORWARD Run/Stop
0 0 0 0 1 1 1 1
RV Reverse Run/Stop
Multi-speed Select,
0 0 0 0 2 2 2 2
CF1
Bit 0 (LSB)
Multi-speed Select,
0 0 0 0 3 3 3 3
CF2
Bit 1
Multi-speed Select,
0 0 0 0 4 4 4 4
CF3
Bit 2
Multi-speed Select,
0 0 0 0 5 5 5 5
CF4
Bit 3 (MSB)
0 0 0 0 6 6 6 6
JG Jogging
0 0 0 0 7 7 7 7
DB External DC braking
Set (select) 2nd Motor
0 0 0 0 8 8 8 8
SET
Data
2-stage Acceleration and
0 0 0 0 9 9 9 9
2CH
Deceleration
11 11 11 11
FRS Free-run Stop
1 1 1 1 2 2 2 2
EXT External Trip
Unattended Start
1 1 1 1 3 3 3 3
USP
Protection
Commercial
1 1 1 1 4 4 4 4
CS
source switchover
1 1 1 1 5 5 5 5
SFT Software Lock
Analog Input
1 1 1 1 6 6 6 6
AT
Voltage/Current Select
1 1 1 1 8 8 8 8
RS Reset Inverter
PTC thermistor Thermal
1 1 1 1 9 9 9 9
PTC Protection
(C005 only)
I I I I nput Function Summary Table nput Function Summary Table nput Function Summary Table nput Function Summary Table
ON Inverter is in Run Mode, motor runs forward
OFF Inverter is in Stop Mode, motor stops
ON Inverter is in Run Mode, motor runs reverse
OFF Inverter is in Stop Mode, motor stops
ON Binary encoded speed select, Bit 0, logical 1
OFF Binary encoded speed select, Bit 0, logical 0
ON Binary encoded speed select, Bit 1, logical 1
OFF Binary encoded speed select, Bit 1, logical 0
ON Binary encoded speed select, Bit 2, logical 1
OFF Binary encoded speed select, Bit 2, logical 0
ON Binary encoded speed select, Bit 3, logical 1
OFF Binary encoded speed select, Bit 3, logical 0
Inverter is in Run Mode, output to motor runs at
ON
jog parameter frequency
OFF Inverter is in Stop Mode
ON DC braking will be applied during deceleration
OFF DC braking will not be applied
The inverter uses 2nd motor parameters for
ON
generating frequency output to motor
The inverter uses 1st (main) motor parameters
OFF
for generating frequency output to motor
Frequency output uses 2nd-stage acceleration
ON
and deceleration values
Frequency output uses standard acceleration
OFF
and deceleration values
Causes output to turn OFF, allowing motor to
ON
free run (coast) to stop
Output
OFF
deceleration stop motor
When assigned input transitions OFF to ON,
ON
inverter latches trip event and displays
No trip event for ON to OFF, any recorded trip
OFF
events remain in history until reset
On powerup, the inverter will not resume a Run
ON
command (mostly used in the US)
On powerup, the inverter will resume a Run
OFF
command that was active before power loss
power ON Motor can be driven by commercial power
OFF Motor is driven via the inverter
The keypad and remote programming devices
ON
are prevented from changing parameters
OFF The parameters may be edited and stored
ON
Refer to "Analog Input Operation" on page 45.
OFF
The trip condition is reset, the motor output is
ON
turned OFF, and powerup reset is asserted
OFF Normal power-ON operation
When a thermistor is connected to terminal [5]
and [L],
ANLG
over-temperature and will cause trip event and
turn OFF output to motor
A disconnect of the thermistor causes a trip
OPEN
event, and the inverter turns OFF the motor
D D D D escr escription escr escr iption iption iption
operates normally, so
the inverter checks
Ver.3− − − − 141
controlled
E E E E 1 1 1 1 2 2 2 2
for