Hitachi WJ200-001S Instruction Manual page 678

N
Nameplate ........................................... 1-3
Navigational
map ............................................. 2-26
trip events ................................... 6-13
NEC .................................................... A-5
NEMA definition ................................... A-5
Netwoak commnucations .............. 1-23,B-2
error code .................................... 6-11
ModBUS data listing ..................... B-24
parameter settings .......................... B-4
protocol reference .......................... B-5
settings ........................................ 3-98
termination resistor ......................... B-3
O
Off-line auto-tuning procedures ........ 3-110
Option card error .............................. 3-111
Open collector outputs ................. 4-51,A-5
Operational
modes ........................................... 3-4
precautions .................................. 2-24
components ............................. 1-2,2-7
Orientation .......................................... 2-2
Other
analog input-related topics ............ 4-88
functions .................................... 3-103
Output
adjustment paramerter ................. 3-95
circuits .................................. 4-4,4-51
deray function.............................. 4-53
deviation for PID control .............. 4-58
logic and timing ......................... 3-102
frequency .................................... 2-34
frequency range ...................... Ver.3-7
setting ......................................... 3-11
summary table ............................. 3-91
motor .......................................... 1-20
overload ...................................... 3-48
Over-current trip ................................ 3-44
suppression .................... 3-51, Ver.3-6
torque signal ............................... 4-61
Overload
Advance notice signal ....4-57,Ver.3.1-2
configuration ............................... 3-48
error codes .................................... 6-8
restriction .................................... 3-51
restriction source
changeover ................................. 4-37
warring output ............................. 3-95
Override source settings .................... 3-13
Over/under torque outpur ................... 3-95
Over-voltage trip ................................ 3-44
error code ................ 6-8,6-9,6-10,6-11
P
P Group other parameter ................... 3-111
Paramerter editing ..................... 2-25,2-29
setting ................................. 1-21,2-26
listing ........................................... C-2
Password function ............................ 3-81
Periodical check ................................. E-3
Permission
Of run command .......................... 4-50
for torque command input ............ 4-42
PID
loop ...................................... 1-25,A-5
clear ........................................... 4-32
configuration .............................. 3-33
control ........................................ 3-31
deviation monitor ..................... Ver.3-5
deviation output .......................... 3-34
disable ........................................ 4-32
error ..................................... 4-58,A-3
error inversion ............................. 3-33
feedback comparison
output ......................................... 3-34
output limit .................................. 3-33
output monitor ......................... Ver.3-5
process variable definition ............. A-6
second stage output .................... 4-71
settings ....................................... 3-31
scalling ....................................... 3-34
sleep function ............................. 3-34
PLC connecting toI .............................. 4-4
PM motor drive .............................. Ver.2-2
Poles of motor .................. 1-24,2-33,3-104
Position feedback monitor .............. Ver.3-3
Positioning completion ....................... 4-69
Potentionmerter .................. 2-30,3-12,4-55
Power
factor ............................................ A-5
on time expiration signal ............... 4-64
Powerup fail ..................................... 3--44
Power test ......................................... 2-23
Power test observations ................... 2-36
acceleration and
decceleration ................................ 2-36
error codes .................................. 2-36
interpreting the display ................. 2-36
inverter at stop ............................. 2-36
monitor/program modes ................ 2-36
run/stop vs monitor/program
modes .......................................... 2-36
speed(RPM) ................................. 2-36
Powerup unattended start .................. 4-25
error coder ...................... 6-9,6-10,6-11
Powering the inverter ........................ 2-24
Preventative maintenancet ................. 6-15
Pre test ............................................. 2-24
Process variable .................................. A-6
Proof test ............................................ A-6
Program mode ...................... 2-26,2-34,3-4
Programming device ............................ 3-2
Proportional gain ............................... 3-31
Pulse
counter clear ............................... 4-40
train input A/B ............... 4-89, Ver.3-10
train input monitor ................... Ver.3-4
PV source settting ............................. 3-31
PW M ................................................... A-6
Index− − − − 5