Hitachi WJ200-001S Instruction Manual page 635

Ver.3− − − − 126
Func. Func.
Func. Func.
Code Code Code Code
A A A A 0 0 0 0 98 98 Deceleration curve selection
98 98
A A A A 1 1 1 1 0 0 0 0 1 1 1 1 [OI] input active range
start frequency
A A A A 1 1 1 1 0 0 0 0 2 2 2 2 [OI] input active range end
frequency
A A A A 1 1 1 1 0 0 0 0 3 3 3 3 [OI] input active range
start current
A A A A 1 1 1 1 0 0 0 0 4 4 4 4 [OI] input active range end
current
A A A A 1 1 1 1 0 0 0 0 5 5 5 5 [OI] input start frequency
select
A A A A 1 1 1 1 3 3 3 3 1 1 1 1 Acceleration curve constant
Deceleration curve constant
A A A A 1 1 1 1 32 32 32 32
A A A A 1 1 1 1 4 4 4 4 1 1 1 1 A input select for calculate
function
A A A A 1 1 1 1 42 42 42 42 B input select for calculate
function
Calculation symbol
A A A A 1 1 1 1 43 43 43 43
A A A A 1 1 1 1 45 45 ADD frequency
45 45
A A A A 1 1 1 1 4 4 4 4 6 6 6 6 ADD direction select
A A A A 1 1 1 1 5 5 5 5 0 0 0 0 Curvature of EL-S-curve at
the start of acceleration
" " " " A A A A " " " " Function Function
Function Function
N N N N ame ame ame ame
Set the characteristic curve of
Dec1 and Dec2, options are same
as above (A A A A 0 0 0 0 97
The output frequency
corresponding to the analog input
range starting point,
range is 0.00 to 400.0(580.0)
The output frequency
corresponding to the current input
range ending point,
range is 0.00 to 400.0(580.0)
The starting point (offset) for the
current input range,
range is 0. to 100.%
The ending point (offset) for the
current input range,
range is 0. to 100.%
Two options; select codes:
00 ... Use offset (A A A A 1 1 1 1 0 0 0 0 1 1 1 1 value) 00
00 00
0 0 0 0 1 1 1 1 ... Use 0Hz
Range is 01 to 10.
Range is 01 to 10.
Seven options:
00 ... Operator 00
00 00
0 0 0 0 1 1 1 1 ... POT on ext. Operator
*Valid when connecting
OPE-SR/SRmini
0 0 0 0 2 2 2 2 ... Terminal [O] input
0 0 0 0 3 3 3 3 ... Terminal [OI] input
0 0 0 0 4 4 4 4 ... RS485
0 0 0 0 5 5 5 5 ... Option
0 0 0 0 7 7 7 7 ... Pulse train input
Seven options:
00 00 ... Operator 00 00
0 0 0 0 1 1 1 1 ... POT on ext. Operator
*Valid when connecting
OPE-SR/SRmini
0 0 0 0 2 2 2 2 ... Terminal [O] input
0 0 0 0 3 3 3 3 ... Terminal [OI] input
0 0 0 0 4 4 4 4 ... RS485
0 0 0 0 5 5 5 5 ... Option
0 0 0 0 7 7 7 7 ... Pulse train input
Calculates a value based on the A
input source (A A A A 1 1 1 1 4 4 4 4 1 1 1 1 selects) and B
input source (A A A A 1 1 1 1 42
Three options:
00 00 ... ADD (A input + B input) 00 00
0 0 0 0 1 1 1 1 ... SUB (A input - B input)
0 0 0 0 2 2 2 2 ... MUL (A input * B input)
An offset value that is applied to
the output frequency when the
[ADD] terminal is ON.
Range is 0.00 to 400.(580.)
Two options:
00 ... Plus (adds A A A A 1 1 1 1 45 00
00 00
output frequency setting)
0 0 0 0 1 1 1 1 ... Minus (subtracts A A A A 1 1 1 1 45
from the output frequency
setting)
Range is 0. to 50.%
D D D D escription escription escription escription
97) 97 97
*1 Hz
*1 Hz
42 42 selects). 42
*1 Hz
45 value to the
45 45
45 value
45 45
D D D D efaults efaults
efaults efaults
A A A A B B B B
Initial data Initial data Initial data Initial data
01
0.00
0.00
20.
100.
00
2
2
02
03
00
0.00
00
10.
Units Units Units Units
−
Hz
Hz
%
%
−
−
−
−
−
−
Hz
−
%