Hitachi WJ200-001S Instruction Manual page 463

Ver.234
Parameter group C
Register
Function name
No.
1401h Input [1] function
1402h Input [2] function
1403h Input [3] function
1404h Input [4] function
1405h Input [5] function
1406h Input [6] function
1407h Input [7] function
1408h to
(Reserved)
140Ah
140Bh Input [1] active state
140Ch Input [2] active state
140Dh Input [3] active state
140Eh Input [4] active state
140Fh Input [5] active state
1410h Input [6] active state
1411h Input [7] active state
1412h to
(Reserved)
1414h
Function
R/W
code
C001 R/W 1 (RV: Reverse RUN), 2 (CF1: Multispeed 1 setting), 3 (CF2:
Multispeed 2 setting), 4 (CF3: Multispeed 3 setting), 5 (CF4:
Multispeed 4 setting), 6 (JG: Jogging), 7 (DB: external DC
braking), 8 (SET: Set 2nd motor data), 9 (2CH: 2-stage
acceleration/deceleration), 11 (FRS: free-run stop), 12 (EXT:
external trip), 13 (USP: unattended start protection), 14: (CS:
C002 R/W commercial power source enable), 15 (SFT: software lock), 16
(AT: analog input voltage/current select), 18 (RS: reset), 20 (STA:
starting by 3-wire input), 21 (STP: stopping by 3-wire input), 22
(F/R: forward/reverse switching by 3-wire input), 23 (PID: PID
disable), 24 (PIDC: PID reset, 27 (UP: remote control UP
function), 28 (DWN: remote control DOWN function), 29 (UDC:
C003 R/W remote control data clearing), 31 (OPE: forcible operation), 32
(SF1: multispeed bit 1), 33 (SF2: multispeed bit 2), 34 (SF3:
multispeed bit 3), 35 (SF4: multispeed bit 4), 36 (SF5: multispeed
bit 5), 37 (SF6: multispeed bit 6), 38 (SF7: multispeed bit 7), 39
(OLR: overload restriction selection), 40 (TL: torque limit enable),
41 (TRQ1: torque limit selection bit 1), 42 (TRQ2: torque limit
C004 R/W selection bit 2), 44 (BOK: braking confirmation), 46 (LAC: LAD
cancellation), 47 (PCLR: clearance of position deviation), 50
(ADD: trigger for frequency addition [A145]), 51 (F-TM:
forcible-terminal operation), 52 (ATR: permission of torque
command input), 53 (KHC: cumulative power clearance), 56
(MI1: general-purpose input 1), 57 (MI2: general-purpose input
C005 R/W 2), 58 (MI3: general-purpose input 3), 59 (MI4: general-purpose
input 4), 60 (MI5: general-purpose input 5), 61 (MI6:
general-purpose input 6), 62 (MI7: general-purpose input 7), 65
(AHD: analog command holding), 66 (CP1: multistage position
settings selection 1 ), 67 (CP2: multistage position settings
selection 2), 68 (CP3: multistage position settings selection 3), 69
C006 R/W (ORL: Zero-return limit function), 70 (ORG: Zero-return trigger
function), 73 (SPD: speed / position switching), 77 (GS1: safety
input 1), 78 (GS2: safety input 2), 81 (485: EzCOM), 82 (PRG:
executing EzSQ program), 83 (HLD: retain output frequency), 84
(ROK: permission of run command), 85 (EB: Rotation direction
detection(for V/f with ENC), 86 (DISP: Display limitation),
255 (no: no assignment),
C007 R/W
- - Inaccessible
C011 R/W 0 (NO), 1 (NC)
C012 R/W 0 (NO), 1 (NC)
C013 R/W 0 (NO), 1 (NC)
C014 R/W 0 (NO), 1 (NC)
C015 R/W 0 (NO), 1 (NC)
C016 R/W 0 (NO), 1 (NC)
C017 R/W 0 (NO), 1 (NC)
- - Inaccessible
Monitoring and setting items
Data
resolution
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-