Hitachi WJ200-001S Instruction Manual page 643

Ver.3− − − − 134
Func. Func.
Func. Func.
N N N N ame ame ame ame
Code Code Code Code
b b b b 1 1 1 1 6 6 6 6 3 3 3 3 Frequency set in
monitoring
b b b b 1 1 1 1 6 6 6 6 4 4 4 4 Automatic return
to the initial
display
b b b b 1 1 1 1 6 6 6 6 5 5 5 5 Ex. operator com.
loss action
Data Read/Write
b b b b 1 1 1 1 66 66 66 66
select
b b b b 1 1 1 1 7 7 7 7 1 1 1 1 Inverter mode
selection
b b b b 1 1 1 1 8 8 8 8 0 0 0 0 Initialization
trigger
b b b b 1 1 1 1 9 9 9 9 0 0 0 0 Password
Settings A
b b b b 1 1 1 1 9 9 9 9 1 1 1 1 Password
authentication A
b b b b 1 1 1 1 9 9 9 9 2 2 2 2 Password
Settings B
Password
b b b b 1 1 1 1 9 9 9 9 3 3 3 3
authentication B
b b b b 9 9 9 9 1 1 1 1 0 0 0 0 Electronic
*2
thermal
subtraction
function selection
b b b b 9 9 9 9 11 11 Thermal
11 11
*2
subtraction time
b b b b 9 9 9 9 1 1 1 1 2 2 2 2 Thermal
*2
subtraction time
constant
b b b b 9 9 9 9 1 1 1 1 3 3 3 3 Thermal
*2
accumulation
gain
: Available from version 3.0
*2
: Power cycle is required to reflect a change.
*3
" " " " b b b b " " " " Function Function
Function Function
D D D D escription
Two option codes:
00 00 00 00 ... Freq. set disabled
0 0 0 0 1 1 1 1 ... Freq. set enabled
10 min. after the last key operation, display returns to the initial
parameter set by b b b b 0 0 0 0 3 3 3 3 8 8 8 8 . Two option codes:
00 ... Disable 00
00 00
0 0 0 0 1 1 1 1 ... Enable
Five option codes:
00 ... Trip 00 00 00
0 0 0 0 1 1 1 1 ... Trip after deceleration to a stop
0 0 0 0 2 2 2 2 ... Ignore
0 0 0 0 3 3 3 3 ... Coasting (FRS)
0 0 0 0 4 4 4 4 ... Decelerates to a stop
00 00 00 00 ... Read/Write OK
0 0 0 0 1 1 1 1 ... Protected
Three option codes:
00 ... No function 00 00 00
0 0 0 0 1 1 1 1 ... Std. IM (Induction Motor)
0 0 0 0 2 2 2 2 ... Reserved
0 0 0 0 3 3 3 3 ... PM (Permanent Magnet Motor)
This is to perform initialization by parameter input with b b b b 0 0 0 0 8 8 8 8 4 4 4 4 ,
b b b b 0 0 0 0 8 8 8 8 5 5 5 5 and b b b b 0 0 0 0 9 9 9 9 4 4 4 4 . Two option codes:
00 ... Initialization disable 00 00 00
0 0 0 0 1 1 1 1 ... Perform initialization
0000(Invalid Password)
0001-FFFF(Password)
0000-FFFF
0000(Invalid Password)
0001-FFFF(Password)
0000-FFFF
00 00 00 00...OFF
0 0 0 0 1 1 1 1 ...Linear subtraction: pre-fixed ratio
0 0 0 0 2 2 2 2 ...Linear subtraction: ratio set in b911
0 0 0 0 3 3 3 3 ...Subtraction with first-order lag filter:
ratio set in b912
0.10 to 100000.00[s] (upper four digits are shown)
0.10 to 100000.00[s] (upper four digits are shown)
1.0 to 200.0 [%]
escription escription escription
D D D D efaults efaults
efaults efaults
A A A A B B B B
Initial data Initial data Initial data Initial data Units Units Units Units
00 -
00 -
02 -
00 -
00 -
00 -
0000 -
0000 -
0000 -
0000 -
03
−
600.0 s
120.00 s
100.0 %