Hitachi WJ200-001S Instruction Manual page 646

Func. Func. Func. Func.
N N N N ame ame ame ame
Code Code
Code Code
C C C C 0 0 0 0 5 5 5 5 8 8 8 8 Over/under-torque level
(Forward regen. mode)
C C C C 0 0 0 0 5 5 5 5 9 9 9 9 Signal output mode of
Over/under-torque
C C C C 0 0 0 0 6 6 6 6 1 1 1 1 Electronic thermal
warning level
C C C C 0 0 0 0 6 6 6 6 3 3 3 3 Zero speed detection level
C C C C 0 0 0 0 6 6 6 6 4 4 4 4 Heat sink overheat
warning
C C C C 0 0 0 0 7 7 7 7 1 1 1 1 Communication speed
*3
C C C C 0 0 0 0 7 7 7 7 2 2 2 2 Modbus address
Communication parity
C C C C 0 0 0 0 7 7 7 7 4 4 4 4
*3
C C C C 0 0 0 0 7 7 7 7 5 5 5 5 Communication stop bit
*3
Communication error
C C C C 0 0 0 0 76 76 76 76
select
C C C C 0 0 0 0 77 77 77 77 Communication error
time-out
C C C C 0 0 0 0 78 78 78 78 Communication wait time
C C C C 0 0 0 0 8 8 8 8 1 1 1 1 O input span calibration
C C C C 0 0 0 0 8 8 8 8 2 2 2 2 OI input span calibration
Thermistor input (PTC)
C C C C 0 0 0 0 8 8 8 8 5 5 5 5
span calibration
C C C C 0 0 0 0 9 9 9 9 1 1 1 1 Debug mode enable
Communication selection
C C C C 0 0 0 0 96 96 96 96
*3
C C C C 0 0 0 0 98 98 EzCOM start adr. of
98 98
*3
master
EzCOM end adr. of master
C C C C 0 0 0 0 99 99 99 99
*3
C C C C 1 1 1 1 00 00 EzCOM starting trigger
00 00
*3
" " " " C C C C " " " " Function Function
Function Function
D D D D escription escription escription escription
Set range is 0. to 200.%
Two option codes:
00 ... During accel., decel. and constant speed 00
00 00
0 0 0 0 1 1 1 1 ... During constant speed only
Set range is 0 to 100%
Setting 0 means disabled.
Set range is 0.00 to 100.0Hz
Set range is 0. to 110. ° C
Eight option codes:
0 0 0 0 3 3 3 3 ... 2,400 bps
0 0 0 0 4 4 4 4 ... 4,800 bps
0 0 0 0 5 5 5 5 ... 9,600 bps
0 0 0 0 6 6 6 6 ... 19,200 bps
0 0 0 0 7 7 7 7 ... 38,400 bps
0 0 0 0 8 8 8 8 ... 57,600 bps
0 0 0 0 9 9 9 9 ... 76,800 bps
1 1 1 1 0 0 0 0 ... 115,200 bps
Set the address of the inverter on the network. Range is 1
to 247
Three option codes:
00 00 00 00 ... No parity
0 0 0 0 1 1 1 1 ... Even parity
0 0 0 0 2 2 2 2 ... Odd parity
Two option codes:
1 1 1 1 ... 1 bit
2 2 2 2 ... 2 bit
Selects inverter response to communications error.
Five options:
00 00 ... Trip
00 00
0 0 0 0 1 1 1 1 ... Decelerate to a stop and trip
0 0 0 0 2 2 2 2 ... Disable
0 0 0 0 3 3 3 3 ... Free run stop (coasting)
0 0 0 0 4 4 4 4 ... Decelerates to a stop
Sets the communications watchdog timer period.
Range is 0.00 to 99.99 sec
0.0 = disabled
Time the inverter waits after receiving a message before it
transmits.
Range is 0. to 1000. ms
Scale factor between the external frequency command on
terminals L–O (voltage input) and the frequency output,
range is 0.0 to 200.0%
Scale factor between the external frequency command on
terminals L–OI (voltage input) and the frequency output,
range is 0.0 to 200.0%
Scale factor of PTC input.
Range is 0.0 to 200.0%
Factory use only. Do not change.
00 00 ... Modbus-RTU 00 00
0 0 0 0 1 1 1 1 ... EzCOM
0 0 0 0 2 2 2 2 ... EzCOM<administrator>
1 to 8
1 to 8
00 00 ... Input terminal
00 00
0 0 0 0 1 1 1 1 ... Always
Ver.3− − − − 137
D D D D efaults efaults
efaults efaults
A A A A B B B B
In In In Initial itial itial itial
Units Units Units Units
data data
data data
100. %
01 -
90. %
0.00 Hz
100. ° C
05 baud
1.
−
00
−
1 bit
02
−
0.00 s
0. ms
100.0 %
100.0 %
100.0 %
00
−
1.
−
1.
−
00
−