Hitachi WJ200-001S Instruction Manual page 660

Expansion Card Functions
"P" parameters will be appeared when the expansion option is connected.
Func. Func.
Func. Func.
N N N N ame ame ame ame
Code Code Code Code
Reaction when
P P P P 00 00 001 1 1 1 00
option card error
occurs
P P P P 00 003 3 3 3 [EA] terminal
00 00
selection
P P P P 00 004 4 4 4 Pulse train input
00 00
mode selection for
feedback
P P P P 0 0 0 0 11 11 11 11 Encoder pulse
setting
P P P P 0 0 0 0 1 1 1 1 2 2 2 2 Simple
positioning
selection
P P P P 0 0 0 0 1 1 1 1 4 4 4 4 Creep pulse ratio
*2
P0 P0 P0 P01 1 1 1 5 5 5 5 Creep Speed
P P P P 0 0 0 0 1 1 1 1 7 7 7 7 Positioning
*
completion range
2
P P P P 0 0 0 0 2 2 2 2 6 6 6 6 Over-speed error
detection level
P P P P 0 0 0 0 2 2 2 2 7 7 7 7 Speed deviation
error detection
level
Deceleration time
P P P P 0 0 0 0 3 3 3 3 1 1 1 1
Input Type
P P P P 0 0 0 0 33 33 33 33 Torque command
input selection
P P P P 0 0 0 0 34 34 34 34 Torque command
level input
P03 3 3 3 6 6 6 6 P0 Torque bias mode
P0 P0
selection
Torque bias value
P03 3 3 3 7 7 7 7 P0 P0 P0
setting
P03 3 3 3 8 8 8 8 P0 P0 P0 Torque bias polar
selection
Speed limit of
P0 P0 P0 P03 3 3 3 9 9 9 9
Torque control
(Forward
rotation)
P04 4 4 4 0 0 0 0 P0 Speed limit of
P0 P0
Torque control
(Forward
rotation)
P04 4 4 4 1 1 1 1 P0 Speed / Torque
P0 P0
control switching
time
" " " " P P P P " " " " Function Function Function Function
D D D D escription escription escription escription
Two option codes:
00 00 00...Inverter trips 00
0 0 0 0 1 1 1 1 ...Ignores the error (Inverter
continues operation)
Three option codes:
00...Speed reference (incl. PID) 00
00 00
0 0 0 0 1 1 1 1 ...For control with encoder feedback
0 0 0 0 2 2 2 2 ...Extended terminal for EzSQ
Four option codes:
00 00...Single-phase pulse [EA]
00 00
0 0 0 0 1 1 1 1 ...2-phase pulse (90 ° difference) 1
([EA] and [EB])
0 0 0 0 2 2 2 2 ...2-phase pulse (90 ° difference) 2
([EA] and [EB])
0 0 0 0 3 3 3 3 ...Single-phase pulse [EA] and
direction signal [EB]
Sets the pulse number (ppr) of the
encoder, set range is 32 to 1024 pulses
Two option codes:
00 00...simple positioning deactivated
00 00
0 0 0 0 1 1 1 1 ...simple positioning activated
0.0 to 400.0[%]
Set range is start frequency (b b b b 0 0 0 0 8 8 8 8 2 2 2 2 ) to
10.00 Hz
0 to 9999. /1000 (10000) [pulse]
Set range is 0 to150%
Set range is 0 to 120 Hz
00 00...Operator
00 00
0 0 0 0 1 1 1 1 ...EzSQ
Three option codes:
00...Analog voltage input [O] 00 00 00
0 0 0 0 1 1 1 1 ...Analog current input [OI]
0 0 0 0 3 3 3 3 ...Operator
0 0 0 0 6 6 6 6 ...Option
Set range is 0 to 200%
Two option codes:
00...No bias 00
00 00
0 0 0 0 1 1 1 1 ...Operator
0 0 0 0 5 5 5 5 ... Option
Range is –200 to 200%
Three option codes:
00 00 00 00...According to the sign
0 0 0 0 1 1 1 1 ...According to the rotation direction
Set range is 0.00 to 120.00Hz
Set range is 0.00 to 120.00Hz
Set range is 0 to 1000 ms
D D D D efaults efaults efaults efaults
A A A A B B B B
Initial data Initial data Initial data Initial data Units Units Units Units
00
00
00
512
00
125.0
%
5.00
Hz
50
Pulses
115.0
%
10.00
Hz
00
00
0.
%
00
0.
%
00
0.00
Hz
0.00
Hz
0.
ms
Ver.3− − − − 151
-
-
-
-
-
-
-
-
-