Hitachi WJ200-001S Instruction Manual page 651

Ver.3− − − − 142
O O O O ption ption T T T T erminal erminal
ption ption erminal erminal
C C C C ode ode S S S S ymbol ymbol
ode ode ymbol ymbol
2 2 2 2 0 0 0 0
STA
2 2 2 2 1 1 1 1
STP
22 22
22 22
F/R
23 23 23 23
PID
24 24 24 24
PIDC
2 2 2 2 7 7 7 7
UP
2 2 2 2 8 8 8 8
DWN
2 2 2 2 9 9 9 9
UDC
3 3 3 3 1 1 1 1
OPE
32 32 32 32
SF1
33 33 33 33
SF2
34 34 34 34
SF3
35 35
35 35
SF4
3 3 3 3 6 6 6 6
SF5
3 3 3 3 7 7 7 7
SF6
3 3 3 3 8 8 8 8
SF7
3 3 3 3 9 9 9 9
OLR
I I I I nput Function Summary Table nput Function Summary Table nput Function Summary Table nput Function Summary Table
F F F F unction Name unction Name unction Name unction Name
Start
(3-wire interface)
Stop
(3-wire interface)
FWD, REV
(3-wire interface)
PID Disable
PID Reset
Remote Control UP
Function (motorized
speed pot.)
Remote Control Down
Function (motorized
speed pot.)
Remote Control Data
Clearing
Operator Control
Multi-speed Select,
Bit operation Bit 1
Multi-speed Select,
Bit operation Bit 2
Multi-speed Select,
Bit operation Bit 3
Multi-speed Select,
Bit operation Bit 4
Multi-speed Select,
Bit operation Bit 5
Multi-speed Select,
Bit operation Bit 6
Multi-speed Select,
Bit operation Bit 7
Overload Restriction
Source Changeover
D D D D escr escr escr escription
ON Starts the motor rotation
OFF No change to present motor status
ON Stops the motor rotation
OFF No change to present motor status
Selects the direction of motor rotation: ON =
FWD. While the motor is rotating, a change of
ON
F/R will start a deceleration, followed by a
change in direction
Selects the direction of motor rotation: OFF =
REV. While the motor is rotating, a change of
OFF
F/R will start a deceleration, followed by a
change in direction
Temporarily disables PID loop control. Inverter
ON output turns OFF as long as PID Enable is
active (A A A A 0 0 0 0 7 7 7 7 1 1 1 1 =0 0 0 0 1 1 1 1 )
Has no effect on PID loop operation, which
OFF operates normally if PID Enable is active
(A A A A 0 0 0 0 7 7 7 7 1 1 1 1 =0 0 0 0 1 1 1 1 )
Resets the PID loop controller. The main
ON consequence is that the integrator sum is forced
to zero
OFF No effect on PID controller
Accelerates (increases output frequency) motor
ON
from current frequency
OFF Output to motor operates normally
Decelerates (decreases output frequency) motor
ON
from current frequency
OFF Output to motor operates normally
Clears the UP/DWN frequency memory by
forcing it to equal the set frequency parameter
ON
F001. Setting C C C C 1 1 1 1 0 0 0 0 1 1 1 1 must be set=00
this function to work
OFF UP/DWN frequency memory is not changed
Forces the source of the output frequency setting
ON A A A A 00 00 001 1 1 1 and the source of the Run command A A A A 00 00
to be from the digital operator
Source of output frequency set by A A A A 00
OFF
source of Run command set by A A A A 00
ON Bit encoded speed select, Bit 1, logical 1
OFF Bit encoded speed select, Bit 1, logical 0
ON Bit encoded speed select, Bit 2, logical 1
OFF Bit encoded speed select, Bit 2, logical 0
ON Bit encoded speed select, Bit 3, logical 1
OFF Bit encoded speed select, Bit 3, logical 0
ON Bit encoded speed select, Bit 4, logical 1
OFF Bit encoded speed select, Bit 4, logical 0
ON Bit encoded speed select, Bit 5, logical 1
OFF Bit encoded speed select, Bit 5, logical 0
ON Bit encoded speed select, Bit 6, logical 1
OFF Bit encoded speed select, Bit 6, logical 0
ON Bit encoded speed select, Bit 7, logical 1
OFF Bit encoded speed select, Bit 7, logical 0
ON Perform overload restriction
OFF Normal operation
iption iption iption
00 to enable 00 00
002 2 2 2 00 00
001 1 1 1 and
00 00
002 2 2 2 is used
00 00