Hitachi WJ200-001S Instruction Manual page 448

Coil
No.
002Dh OL2 (overload notice advance (2))
002Eh Odc: Analog O disconnection detection
OIDc: Analog OI disconnection
002Fh
detection
0030h (Reserved)
0031h (Reserved)
0032h FBV (PID feedback comparison)
NDc (communication train
0033h
disconnection)
0034h LOG1 (logical operation result 1)
0035h LOG2 (logical operation result 2)
0036h LOG3 (logical operation result 3)
0037h (Reserved)
0038h (Reserved)
0039h (Reserved)
003Ah WAC (capacitor life warning)
003Bh WAF (cooling-fan speed drop)
003Ch FR (starting contact signal)
003Dh OHF (heat sink overheat warning)
003Eh LOC (low-current indication signal)
003Fh M01 (general output 1)
0040h M02 (general output 2)
0041h M03 (general output 3)
0042h (Reserved)
0043h (Reserved)
0044h (Reserved)
0045h IRDY (inverter ready)
0046h FWR (forward rotation)
0047h RVR (reverse rotation)
0048h MJA (major failure)
0049h Data writing in progress
004Ah CRC error
004Bh Overrun
004Ch Framing error
004Dh Parity error
004Eh Sum check error
004Fh (Reserved)
0050h WCO (window comparator O)
0051h WCOI (window comparator OI)
0052h (Reserved)
0053h OPDc (option disconnection)
0054h FREF (FQ command source)
0055h REF (RUN command source)
0056h SETM (2nd motor selected)
0057h (Reserved)
0058h EDM (Gate suppress monitor)
0059h- unused
*1 Normally, this coil is turned on when the corresponding intelligent input terminal on the control circuit terminal
block is turned on or the coil itself is set to on. In this regard, the operation of the intelligent input terminal has
priority over the operation of the coil. If disconnection of the communication train has disabled the master system
from turning off the coil, turn the corresponding intelligent input terminal on the control circuit block on and off.
This operation turns off the coil.
*2 Communication error data is retained until an error reset command is input. (The data can be reset during the
inverter operation.)
Item R/W
R
-
-
-
-
R
R
R
R
R
-
-
-
R
R
R
R
R
R
R
R
-
-
-
R
R
R
R
R
R
R
R
R
R
-
R
R
-
R
R
R
R
-
R
R
Setting
1: ON, 0: OFF
1: ON, 0: OFF
1: ON, 0: OFF
-
-
1: ON, 0: OFF
1: ON, 0: OFF
1: ON, 0: OFF
1: ON, 0: OFF
1: ON, 0: OFF
-
-
-
1: ON, 0: OFF
1: ON, 0: OFF
1: ON, 0: OFF
1: ON, 0: OFF
1: ON, 0: OFF
1: ON, 0: OFF
1: ON, 0: OFF
1: ON, 0: OFF
-
-
-
1: ON, 0: OFF
1: ON, 0: OFF
1: ON, 0: OFF
1: ON, 0: OFF
1: Writing in progress, 0: Normal status
1: Error detected, 0: No error (*2)
1: Error detected, 0: No error (*2)
1: Error detected, 0: No error (*2)
1: Error detected, 0: No error (*2)
1: Error detected, 0: No error (*2)
-
1: ON, 0: OFF
1: ON, 0: OFF
-
1: ON, 0: OFF
1: Operator, 0: Others
1: Operator, 0: Others
1: 2nd motor selected, 0: 1st motor selected
-
1: ON, 0: OFF
inaccessible
Ver.219