Juniper JUNOSE SOFTWARE 11.2.X - BROADBAND ACCESS CONFIGURATION GUIDE 7-20-2010 Configuration Manual page 764

JunosE 11.2.x Broadband Access Configuration Guide
deactivating..........................................................652
with IPv4 services..............................................650
IPv6-Acct-Input-Gigawords [26-155] .........................224
IPv6-Acct-Input-Octets [26-151] ..................................224
IPv6-Acct-Input-Packets [26-153]...............................224
IPv6-Acct-Output-Gigawords [26-156].....................224
IPv6-Acct-Output-Octets [26-152]..............................224
IPv6-Acct-Output-Packets [26-154] ..........................224
Ipv6-Local-Interface (RADIUS attribute
26-46)...................................................................................217
Ipv6-NdRa-Prefix (RADIUS attribute 26-46)............222
IPv6-NdRa-Prefix attribute
used for IPv6 Neighbor Discovery
from Access-Accept messages.......................87
IPv6-Primary-DNS (RADIUS attribute 26-47)...........217
Ipv6-Secondary-DNS (RADIUS attribute
26-46)...................................................................................217
IPv6-Virtual-Router (RADIUS attribute
26-45)...................................................................................216
K
key command................................................29, 77, 238, 246
L
L2C-Down-Stream-Data (RADIUS attribute
26-93)...................................................................................221
L2C-Information (RADIUS attribute 26-81)................221
L2C-Up-Stream-Data (RADIUS attribute
26-92)...................................................................................221
L2TP (Layer 2 Tunneling Protocol)
defining............................................................................329
high availability considerations..............................336
implementation.............................................................331
license..............................................................................335
modifying LAC default settings....................338, 377
monitoring.......................................................................417
peer resynchronization..............................................382
rx speed ..........................................................................358
sessions supported.....................................................335
silent failover.................................................................382
tunnel selection...........................................................362
tunnel switch profiles................................................385
L2TP access concentrator. See LAC
l2tp commands.....................................................................377
disconnect-cause.........................................................377
failover-resync .............................................................385
l2tp checksum..............................................................339
l2tp destination lockout-test...................................361
l2tp destination lockout-timeout...........................361
726
l2tp destination profile.....................................368, 371
l2tp destruct-timeout................................................339
l2tp disable calling-number avp............................343
l2tp disable challenge................................................352
l2tp disconnect-cause...............................................377
l2tp drain........................................................................340
l2tp drain destination................................................340
l2tp drain tunnel..........................................................340
l2tp fail-over-within-preference............................363
l2tp failover-resync ..........................................382, 385
l2tp ignore-receive-data-sequencing..................352
l2tp ignore-transmit-address-change.................361
l2tp reject-transmit-address-change..................361
l2tp retransmission.....................................................342
l2tp short-drain-timeout..........................................340
l2tp shutdown................................................................341
l2tp shutdown destination.......................................341
l2tp shutdown session...............................................341
l2tp shutdown tunnel.................................................341
l2tp switch-profile......................................................390
l2tp tunnel default-receive-window....................379
l2tp tunnel idle-timeout............................................376
l2tp tunnel test.............................................................376
l2tp tunnel-switching......................................376, 390
l2tp unlock destination..............................................361
l2tp unlock-test destination.....................................361
l2tp weighted-load-balancing command.........363
max-sessions command................................368, 372
See also show l2tp commands
L2TP dial-out
before configuring......................................................408
configuring.....................................................................409
dial-out process..........................................................403
network model.............................................................402
operational states.......................................................403
outgoing call setup details......................................403
Access-Accept message.................................403
Access-Request message..............................403
mutual authentication.....................................403
outgoing call successful..................................403
route installation................................................403
overview..........................................................................401
references......................................................................408
route.................................................................................402
session............................................................................402
target...............................................................................402
trigger...............................................................................402
Copyright © 2010, Juniper Networks, Inc.