BONFIGLIOLI Agile Operating Instructions Manual page 188

Operation mode 531, 532, 533, 554
7 - Ixt warning
8 - Warning Heat Sink Temperature
9 - Warning Inside Temperature
10 - Warning Motor Temperature
11 - Warning, General
12 - Warning Overtemperature
13 - Mains Failure
14 - Warning Motor Protect. Switch
15 - Warning Current Limitation
Conroller Current Limit. Long Term
16 -
Ixt
Conroller Current Limit. Short Term
17 -
Ixt
18 - Controller Current Limit. Tc
19 - Controller Current Limit. Motor Temp.
22 - Warning V-Belt
25 - Warning Mask
26 - Warning, Application
27 - Warning Mask, Application
28 - Warning, gen + Warning, Application A warning or warning application is signaled.
Warn. Mask, gen + Warn. Mask,
29 -
Appl.
30 - Flux-Forming finished
31 - Handshake Traverse Function
41 - Brake release
43 - External fan
50 - Warning service fan
Agile
Operating Instructions
The
Warning limit short-term Ixt
Long-Term Ixt
Max. heat sink temperature T
heat sink temp.
Maximum inside temperature T
limit inside temp.
Warning according to configured
570 and
temp.
The message is displayed via parameter
The selected limit values
407,
Warning limit inside temp.
motor temperature have been exceeded.
Failure of the mains voltage and power regulation ac-
tive according to
controller.
Parameterized
cuit breaker triggered.
A controller or the
gent current limits limit the output current. See chapter
7.6.5.6 "Current limitation".
The overload reserve for 60 s has been used up and
the output current is being limited. See chapter 7.6.5.6
"Current limitation".
The overload reserve for 1 s has been used up and the
output current is being limited. See chapter 7.6.5.6
"Current limitation".
Max. heat sink temperature T
rent limits of
7.6.5.6 "Current limitation".
Maximum motor temperature reached, intelligent cur-
rent limits of
7.6.5.6 "Current limitation".
Warning of
Operation mode
Message of the configurable parameter
536. See chapter 7.6.5.8 "Warning mask".
mask
A warning application is signaled. Display of the actual
value is effected via parameter
273. See chapter 7.6.5.9 "Warning mask, application".
Message of the configurable parameter
mask application
Message of configurable parameters
536 and
mask
Magnetic field has been impressed. See chapter 7.6.5.4
"Flux forming finished".
Signal of the traverse function. See chapter 7.10.8
"Traverse function"
Activation of a brake unit depending on the
620 for the starting behavior,
Mode
630 for the stopping behavior or the configured brake
control system. See chapter 7.6.5.5 "Release brake".
The
Switch-on temperature
external fan can be switched on by the signal. See
chapter 7.6.5.7 "External fan".
The time remaining until service has expired. See chap-
ter 10.3.2 "Fan".
188
06/2013
Parameter descriptions
Function
405 or
406 is reached.
minus the
K
407 reached.
minus the
K
408 reached.
Operation mode motor
Max. motor winding temp.
Warning limit heat sink temp.
408 or the maximum
670 for the voltage
Operation Mode
571 for the motor cir-
Operation Mode
573 of the intelli-
Operation Mode
reached, intelligent cur-
K
573 active. See chapter
Operation Mode
573 active. See chapter
Operation Mode
581 of V-belt monitoring
Application Warnings
626.
Create warning
Create Warning Mask Application
Operation Mode
39 has been reached. An
Control inputs and outputs
Warning Limit
Warning limit
Warning
617.
269.
Warnings
Create warning
Create warning
626.
Operation