BONFIGLIOLI Agile Operating Instructions Manual page 183

Parameter descriptions
With the parameters
Analog: Voltage 100%
100% and 0% of the output parameter is set. If the output value exceeds the reference value, the
output voltage also exceeds the value of the parameter
mum value of 22 V (or the maximum value of an external voltage supply).
NOTE
If
Operation Mode MFO1 (X13.6)
log: Voltage 100%
Analog: Voltage 100%
553 Analog: Source MFO1A
If the multifunction output is to be used as analog output, parameter
550 must be set to "10 - Analog (PWM) MFO1A".
(X13.6)
For parameter
Analog: Source MFO1A
output can be selected.
Parameters
Operation mode MFO1
550
(X13.6)
Analog: Source MFO1A
Analog: Source MFO1A
0 - Off
1 - Abs. Fs
2 - Abs. Fs betw. fmin/fmax
7 - Abs. Actual Frequency
10 - Abs. Reference Percentage
Abs. Ref. Percentage betw.
11 -
%min/%max
20 - Abs. Iactive
21 - Abs. Isd
22 - Abs. Isq
30 - Abs. Pactive
31 - Abs. T
32 - Abs. Inside Temperature
Abs. Heat Sink Tempera-
33 -
ture
34 - Abs. Capacitor temperature Abs. value of measured capacitor temperature. -20 °C ... 100 °C.
40 - Abs. Analog Input MFI1A
41 - Abs. Analog Input MFI2A
50 - Abs. I
51 - DC-Link Voltage
52 - V
Control inputs and outputs
551 and
550 = Analog (PWM) MFO1A and parameter s
551 <
Analog: Voltage 0%
551 is put out.
553, the analog actual value to be output at the multifunction
Factory setting
10 - Analog (PWM) MFO1A
553 7 - Abs. Actual Frequency
553
Analog mode at the multifunction output is switched off.
Abs. value of the stator frequency. 0.00 Hz ...
419.
quency
Abs. value of the stator frequency.
Maximum Frequency
Abs. value of act. frequency. 0.00 Hz ...
419. Factory setting.
Absolute value of reference value from reference percentage
channel. Total of
ence Percentage Source 2
Absolute value of reference value from reference percentage
channel.
Minimum Reference Percentage
erence Percentage
476 and
1 Reference Percentage Source 2
Abs. value of current effective current I
frequency inverter current.
Abs. value of flux-forming current component. 0.0 A ... Nominal
frequency inverter current.
Abs. value of torque-forming current component. 0.0 A ... Nomi-
nal frequency inverter current.
Abs. value of current effective power P
376.
Mech. Power
Abs. value of calculated torque M, 0.0 Nm ... rated torque.
Abs. value of measured inside temperature. -20 °C ... 100 °C.
Abs. value of measured heat sink temperature. -20 °C ... 100 °C.
Abs. signal value at analog input MFI1A. DC 0.0 V ... 10.0 V.
Abs. signal value at analog input MFI2A. DC 0.0 V ... 10.0 V.
Abs. current value of measured output currents. 0.0 A ... Nominal
frequency inverter current.
DC-link voltage U
Output voltage. 3xAC 0.0 V ... 1000.0 V.
183
552, the voltage range at
Analog: Voltage 0%
Analog: Voltage 100%
552, then the smaller voltage value of
Operation Mode MFO1
10 - Analog (PWM) MFO1A
Select an analog signal source.
Function
Minimum Frequency
419.
Maximum Frequency
Reference Percentage Source 1
494.
518 ...
519. Total of
Reference Percentage Source
Active
Active
. DC 0.0 V ... 1000.0 V.
d
06/2013 Operating Instructions
551 up to the maxi-
Ana-
Set
Maximum Fre-
418...
476 and
Refer-
Maximum Ref-
494.
. 0.0 A ... Nominal
. 0.0 kW ...
Rated
Agile