Table of Contents

Advertisement

System Hardware Manual
Doc. No. 10536
Issue 1.5

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the UNIVERGE SV8100 and is the answer not in the manual?

Questions and answers

Summary of Contents for NEC UNIVERGE SV8100

  • Page 1 System Hardware Manual Doc. No. 10536 Issue 1.5...
  • Page 3 NEC Australia Pty Ltd. This document has been prepared for the use of employees and customers of NEC Australia Pty Ltd and may not be reproduced without prior written approval of NEC Australia Pty Ltd. Copyright © 2007 NEC Australia Pty Ltd 633 –...
  • Page 5 This chapter provides important regulatory information. Chapter 1 – Introduction to SV8100/SV8300 This chapter provides an overview of the UNIVERGE SV8100/SV8300 system. Chapter 2 – SV8100 System Specifications This chapter contains detailed specifications for the SV8100 system and should be carefully reviewed by the technician before installing the system.
  • Page 6 Chapter 12 – Installing D Series i Telephones term The UNIVERGE SV8100/SV8300 system supports several different IPK II D Series i Multiline Terminals and an Attendant Console. This chapter describes each terminal and the console and provides instructions for attaching the terminals to the system and for wall mounting.
  • Page 7 Other manuals in the set are described below. OCUMENTS Documents supporting the SV8100 system include: UNIVERGE SV8100 Features and Specifications Manual This manual describes each available feature for the SV8100 system. UNIVERGE SV8100 General Description Manual This manual contains general information about the system features, configuration and standards.
  • Page 8 Documents supporting the SV8300 system include: UNIVERGE SV8300 System Manual Contains the system description, hardware installation procedure and the programming procedure of the SV8300 system. UNIVERGE SV8300 Command Manual Contains the Customer Administration Terminal (CAT) operation, command functions and data required for programming the system and the Resident System Program. UNIVERGE SV8300 Programming Manual Contains procedure for programming each business, hotel, ISDN, OAI, WCS and WLAN feature.
  • Page 9 In the event of equipment malfunction, all repairs must be performed by an authorised dealer of NEC Australia Pty Ltd or by NEC Australia Pty Ltd. It is the responsibility of users requiring service to report the need for service to one of NEC Australia Pty Ltd authorised agents or to NEC Australia Pty Ltd.
  • Page 10 The Australian Performing Right Association Limited (APRA), or other similar organisation, when radio or TV broadcasts are transmitted through the Music On Hold feature of this telecommunication system. NEC Australia Pty Ltd hereby disclaims any liability arising out of the failure to obtain such a license.
  • Page 11 ATTERY ISPOSAL AND AFETY The UNIVERGE SV8100 system includes the batteries listed below. When disposing of these batteries from system chassis, blades or external battery boxes, the maintenance personnel must comply with applicable Federal and State regulations regarding proper disposal procedures.
  • Page 13: Table Of Contents

    Table of Contents Chapter 1 Introduction to SV8100/SV8300 Section 1 General Information ..................1-1 Section 2 Equipment List .................... 1-4 Chapter 2 SV8100 System Specifications Section 1 General Information ..................2-1 Section 2 System Block Diagram ................2-1 Section 3 Maximum System Capacities ..............
  • Page 14 Issue No. 1.5 UNIVERGE SV8100/SV8300 6.6.6 External Tone Ringer/Night Chime Output ....... 2-23 6.6.7 SMDR Output ..............2-23 6.6.8 PC Connection ..............2-24 6.6.9 Relay Contact ..............2-24 Battery Backup ................2-24 6.7.1 System Backup (Optional) ..........2-24 6.7.2 Memory Backup ............... 2-24 Weights and Dimensions ...............
  • Page 15 UNIVERGE SV8100/SV8300 Issue No. 1.5 Dialing Specifications ..............3-22 6.6.1 Dial Pulse Address Signaling ........... 3-22 6.6.2 Dual-Tone Multifrequency (DTMF) Address Signaling ..3-22 6.6.3 External Equipment Connection ........3-23 6.6.4 Music Source for Music on Hold via Chassis ....3-23 6.6.5...
  • Page 16 Issue No. 1.5 UNIVERGE SV8100/SV8300 Section 3 Installing the Chassis ................... 4-5 Wall Mounting the 19” Chassis ............4-6 3.1.1 CHS2U-AU Chassis Wall Mount Installation ...... 4-6 Floor Mounting the 19” Chassis ............. 4-13 3.2.1 CHS2U-AU Chassis Installation ........4-13 3.2.2...
  • Page 17 UNIVERGE SV8100/SV8300 Issue No. 1.5 Chapter 5 Installing the SV8300 Chassis Section 1 General Information ..................5-1 Section 2 Site Preparation and MDF/IDF Construction ..........5-1 Precautionary Information ..............5-1 Surveying the Customer Site ............5-2 Selecting the Best Location for Proper Installation ......5-2 2.3.1...
  • Page 18 Issue No. 1.5 UNIVERGE SV8100/SV8300 Section 4 Battery Connection ..................5-47 Install Internal Batteries ..............5-47 4.1.1 Install Internal Batteries CHS1U-AU Chassis ....5-47 4.1.2 Install Internal Batteries CHS2U-AU Chassis ....5-52 Install External Batteries (without CHS LARGE BATT BOX) ..5-57 Install External Batteries (with CHS LARGE BATT BOX) ....
  • Page 19 UNIVERGE SV8100/SV8300 Issue No. 1.5 Section 3 Common Control Blades ................6-13 CD-CP00-AU (SV8100 Central Processing Unit) ......6-13 3.1.1 Description ............... 6-14 3.1.2 Installation ................ 6-17 3.1.3 Switch Settings ..............6-18 3.1.4 LED Indications ..............6-19 3.1.5 Connectors ............... 6-20 CC-CP00 (SV8300 Central Processing Unit) ........
  • Page 20 Issue No. 1.5 UNIVERGE SV8100/SV8300 CD-4LCA/ CD-8LCA (4-Port/8-Port Single Line Interface) ..... 6-48 4.3.1 Description ............... 6-49 4.3.2 Installation ................ 6-50 4.3.3 Connectors ............... 6-51 PZ-4LCA/PZ-8LCE (4-Port/8-Port SLI Daughter Boards) ....6-52 4.4.1 Description ............... 6-53 4.4.2 Installation ................ 6-54 4.4.3...
  • Page 21 UNIVERGE SV8100/SV8300 Issue No. 1.5 CD-PRTA (Primary Rate Interface) ..........6-77 5.6.1 Description ............... 6-77 5.6.2 Installation ................ 6-78 5.6.3 LED Indications ..............6-79 5.6.4 Connectors ............... 6-81 CD-4ODTA (4-Port Tie Line Interface Blade) ........ 6-83 5.7.1 Description ............... 6-83 5.7.2...
  • Page 22 Issue No. 1.5 UNIVERGE SV8100/SV8300 Chapter 7 Installing DT300/DT700 Series (DTL/ITL) Digital and IP Multiline Terminals Section 1 General Description ..................7-1 Section 2 DT300 Series Digital Multiline Terminals ............. 7-6 Digital MultilineTerminals ..............7-6 2.1.1 DTL-2E-1( ) (BK) TEL ............7-6 2.1.2...
  • Page 23 UNIVERGE SV8100/SV8300 Issue No. 1.5 Installing a Numbered Keypad on the Multiline Terminal ....7-31 4.7.1 Installing the Numbered Keypad on a Multiline Terminal 7-32 4.7.2 Configuring the Digital Telephone for the Numbered Keypad .. 7-34 4.7.3 Configuring the IP Telephone for the Numbered Keypad 7-35 Adjusting the Height on the Multiline Terminal .......
  • Page 24 ................. 8-16 Chapter 9 Installing SV8100/SV8300 Wireless Telephones Section 1 General Description ..................9-1 Section 2 NEC SIP DECT Solutions ................9-1 Installation ..................9-2 Chapter 10 Installing SV8100/SV8300 Optional Equipment Section 1 General Information ................... 10-1 Section 2 PGD(2)-U( ) ADP ..................
  • Page 25 UNIVERGE SV8100/SV8300 Issue No. 1.5 Section 3 Background Music ..................10-9 Installing Background Music ............10-9 Section 4 Door Box ....................10-10 Installing a Door Box ..............10-10 Section 5 External Paging ..................10-14 External Page ................10-14 Installing an External Page System ..........10-14 Section 6 External Paging and Door Box/Page Relays ...........
  • Page 26 Issue No. 1.5 UNIVERGE SV8100/SV8300 11.3.4 VSR Record Tab ............10-33 11.3.5 About Tab ............... 10-34 11.3.6 Options Tab ..............10-35 11.3.7 File Management Tab ............ 10-37 11.3.8 Custom Program Settings ..........10-37 11.4 Operation Note ................10-39 11.5 4-Port Digital Call Logging Unit ............ 10-40 11.5.1...
  • Page 27 UNIVERGE SV8100/SV8300 Issue No. 1.5 Section 13 Power Failure Telephones ............... 10-75 13.1 Power Failure ................10-75 13.2 Connector Pin-Outs on COIU Blade for Power Failure Circuits .. 10-76 13.3 Installing the Power Failure Telephones ........10-76 term Chapter 11 Installing D...
  • Page 28 Issue No. 1.5 UNIVERGE SV8100/SV8300 Section 11 Wall Mounting Multiline Terminals ............11-16 11.1 Wall Mounting a Multiline Terminal using the Base Plate .... 11-17 11.1.1 Adjusting the Hanger Hook ..........11-17 11.1.2 Wall Mounting the Multiline Terminal ......11-17 11.1.3...
  • Page 29 Installing the External Microphone ......... 12-23 Add on Module (ADM) ..............12-23 4.2.1 Connecting the Interface Unit ........12-24 4.2.2 Wall Mounting ADM and Multiline Terminal ....12-25 NEC Push-to-Mute (PTM) or Push-to-Talk (PTT) Handset ..12-27 4.3.1 Description ..............12-27 System Hardware Manual xvii...
  • Page 30 Issue No. 1.5 UNIVERGE SV8100/SV8300 THIS PAGE INTENTIONALLY LEFT BLANK xviii Table of Contents...
  • Page 31 List of Figures Figure 1-1 Simplified SV8100 System Connectivity ..........1-2 Figure 1-2 Simplified SV8300 System Connectivity ..........1-2 Figure 2-1 SV8100 System Block Diagram ............2-3 Figure 2-2 19” Controlling and Expansion Chassis ..........2-5 Figure 2-3 Connecting the DLC Using Twisted 2-Pair Cable ......2-16 Figure 3-1 SV8300 System Block Diagram ............
  • Page 32 Issue No. 1.5 UNIVERGE SV8100/SV8300 Figure 4-16 Assemble Stand Mount with Screws ..........4-17 Figure 4-17 Secure CHS2U-AU Chassis to CHS2U STAND KIT with Screws ..4-18 Figure 4-18 Secure Stand Mount to Floor with Screws ........4-19 Figure 4-19 Attach Rubber Feet to CHS2U-AU Chassis ........
  • Page 33 UNIVERGE SV8100/SV8300 Issue No. 1.5 Figure 4-44 19” Chassis Grounding Lug (Multiple-Chassis) ........ 4-35 Figure 4-45 Install the AC Power Cord ..............4-36 Figure 4-46 Install 19” AC Power Cords (Multiple-Chassis) ........ 4-36 Figure 4-47 Removing Battery Access Panel ............4-37 Figure 4-48 Removing Access Panel ..............
  • Page 34 Issue No. 1.5 UNIVERGE SV8100/SV8300 Figure 4-72 Removing CHS LARGE BATT BOX Cover ........4-51 Figure 4-73 Removing Battery Tray Suppressor ..........4-52 Figure 4-74 Disconnecting Battery Cables ............4-52 Figure 4-75 CHS LARGE BATT BOX Fuse Unit ..........4-53 Figure 4-76 Connecting Battery Cables ...............
  • Page 35 UNIVERGE SV8100/SV8300 Issue No. 1.5 Figure 5-20 Stand Mount Spacing Guide (CHS1U-AU+CHS2U-AUx1 Chassis Installation) ................. 5-20 Figure 5-21 Attach Rubber Feet to CHS2U-US Chassis ........5-21 Figure 5-22 Install Joint Brackets with Screws ............ 5-21 Figure 5-23 Assemble Stand Mount with Screws ..........5-22 Figure 5-24 Attach Floor Mount Brackets to Chassis with Screws ......
  • Page 36 Issue No. 1.5 UNIVERGE SV8100/SV8300 Figure 5-45 PZ-BS10 Blade Installed ..............5-39 Figure 5-46 PZ-BS10 Installed (Cover Closed) ............ 5-39 Figure 5-47 PZ-BS11 Expansion Bay in Expansion Chassis ....... 5-39 Figure 5-48 Open Expansion Chassis Cover ............5-40 Figure 5-49 PZ-BS11 Blade Guides ..............
  • Page 37 UNIVERGE SV8100/SV8300 Issue No. 1.5 Figure 5-73 Installing Two Batteries ..............5-54 Figure 5-74 Installing Battery Cable ..............5-55 Figure 5-75 Connecting CHS2U BATT CA INT ........... 5-55 Figure 5-76 Installing Battery Tray into CHS2U-AU Chassis ....... 5-56 Figure 5-77 Installing the Access Panel ..............
  • Page 38 Issue No. 1.5 UNIVERGE SV8100/SV8300 Figure 5-99 Cable Connection between Chassis and CHS LARGE BATT BOX (3 Hours Battery Backup) ........5-69 Figure 5-100 Removing CHS LARGE BATT BOX Cover ........5-69 Figure 5-101 Removing Battery Tray Suppressor ..........5-70 Figure 5-102 Disconnecting Battery Cables ............
  • Page 39 UNIVERGE SV8100/SV8300 Issue No. 1.5 Figure 6-16 CD-4LCA Blade ................6-48 Figure 6-17 CD-8LCA Blade ................6-49 Figure 6-18 Installing the PZ-4LCA Daughter Board ........... 6-52 Figure 6-19 Installing the PZ-8LCE Daughter Board ........... 6-53 Figure 6-20 CD-LTA Blade .................. 6-56 Figure 6-21 CD-4COTC Blade ................
  • Page 40 Issue No. 1.5 UNIVERGE SV8100/SV8300 Figure 7-3 DTL-8LD-1( ) TEL ................7-8 Figure 7-4 DTL-12D-1( ) TEL ................7-9 Figure 7-5 DTL-12PA-1( ) TEL ................7-10 Figure 7-6 DTL-24D-1( ) TEL ................7-11 Figure 7-7 DTL-32D-1( ) TEL ................7-12 Figure 7-8 ITL-2E-1( ) TEL .................
  • Page 41 UNIVERGE SV8100/SV8300 Issue No. 1.5 Figure 7-31 BS (Retro)-L KIT ................7-32 Figure 7-32 Remove Plastic Panels ..............7-32 Figure 7-33 Removing Numbered Keypad from DT300/DT700 Series Terminal ................7-33 Figure 7-34 Install New Numbered Keypad into DT300/DT700 Series Terminal ................7-33 Figure 7-35 Install Plastic Panels ................
  • Page 42 Issue No. 1.5 UNIVERGE SV8100/SV8300 Figure 7-58 8LKD (LD)-L UNIT Installed .............. 7-49 Figure 7-59 Install Screw ..................7-50 Figure 7-60 8LKI (LD)-L( ) UNIT ................7-50 Figure 7-61 Remove Side Panel from Multiline Terminal ........7-51 Figure 7-62 Ribbon Cable Connector ..............7-52 Figure 7-63 Ribbon Cable Installed ..............
  • Page 43 UNIVERGE SV8100/SV8300 Issue No. 1.5 Figure 7-86 ITL / DTL PTT Handset ..............7-65 Figure 7-87 Installing the UTR-1-1( ) USB Handset Cable ........7-66 Figure 7-88 Installing the UTR-1-1( ) USB Handset to a PC ....... 7-66 Figure 7-89 Wall Mounting the UTR-1-1( ) USB Handset ........
  • Page 44 Issue No. 1.5 UNIVERGE SV8100/SV8300 Figure 8-21 Removing the Connector Cover ............8-15 Figure 8-22 Installing the BHA-L UNIT ..............8-16 Figure 8-23 Entering a PIN Code ................. 8-16 Figure 8-24 Pairing a Device ................8-17 Figure 8-25 Connecting the Paired Device ............8-17 Figure 8-26 Unpairing a Device ................
  • Page 45 VSR Reporter Pro Screen ............. 10-53 Figure 10-44 Installing Adapters ................10-56 Figure 10-45 In-Line Power Adapter ..............10-57 Figure 10-46 In-Line Power Adapter Switch Settings .......... 10-58 Figure 10-47 NEC Terminal Connection to an IEEE 802.3af PoE Switch ... 10-59 System Hardware Manual xxxiii...
  • Page 46 Issue No. 1.5 UNIVERGE SV8100/SV8300 Figure 10-48 ADA-L( ) Unit .................. 10-60 Figure 10-49 Separate Tilt Leg from Leg Support ..........10-62 Figure 10-50 Bottom Option Interface Knockout ..........10-62 Figure 10-51 Install ADA-L( ) Unit ................ 10-62 Figure 10-52 ADA-L( ) OUT Jack Connection ............
  • Page 47 UNIVERGE SV8100/SV8300 Issue No. 1.5 Figure 11-4 DTH-8D-1( ) TEL Multiline Terminal ..........11-4 Figure 11-5 DTH-16-1( ) TEL Multiline Terminal ..........11-4 Figure 11-6 DTH-16D-1( ) TEL Multiline Terminal ..........11-5 Figure 11-7 DTH-16(BL)-1( ) TEL Multiline Terminal ........... 11-6 Figure 11-8 DTH-16LD-1( ) TEL Multiline Terminal ..........
  • Page 48 Issue No. 1.5 UNIVERGE SV8100/SV8300 Figure 11-32 Wall Mounting the Base Plate ............11-19 Figure 11-33 Installing the Multiline Terminal ............11-19 Figure 11-34 Plugging in Line Cord into Multiline Terminal ......... 11-20 Figure 11-35 Hiding Excess Cord ................ 11-20 Figure 11-36 Removing the Multiline Terminal ............
  • Page 49 ADM and Multiline Terminal with Base Covers Removed ....12-24 Figure 12-32 Installing the Connector Plate ............12-25 Figure 12-33 Installing Base Units on the Wall ............ 12-26 Figure 12-34 NEC PTM or PTT Handset ............. 12-27 System Hardware Manual xxxvii...
  • Page 50 Issue No. 1.5 UNIVERGE SV8100/SV8300 THIS PAGE INTENTIONALLY LEFT BLANK xxxviii List of Figures...
  • Page 51 List of Tables Table 1-1 Chassis Equipment List ..............1-4 Table 1-2 Chassis Installation Equipment List ............ 1-5 Table 1-3 Battery Mount Equipment List ............1-5 Table 1-4 Blade Equipment List ................. 1-6 Table 1-5 Cable Equipment List ................. 1-7 Table 1-6 Digital Multiline Terminal (DT300 Series) Equipment List ....
  • Page 52 Issue No. 1.5 UNIVERGE SV8100/SV8300 Table 2-19 Tone Patterns ................... 2-28 Table 2-20 Multiline Terminal LED Flash Pattern ..........2-29 Table 2-21 Traffic Capacity ................. 2-30 Table 3-1 List of Abbreviations ................3-1 Table 3-2 SV8300 Maximum System Capacity ..........3-5 Table 3-3 Maximum System Capacity –...
  • Page 53 UNIVERGE SV8100/SV8300 Issue No. 1.5 Table 4-4 CHS LARGE BATT BOX Capacity ........... 4-42 Table 5-1 Power Failure Transfer Connections ..........5-4 Table 5-2 PZ-BS10/PZ-BS11 Connector Pin-Out ..........5-36 Table 5-3 Battery Capacity of Single External Battery ........5-61 Table 5-4 Battery Capacity of Multiple External Batteries ........
  • Page 54 Issue No. 1.5 UNIVERGE SV8100/SV8300 Table 6-24 CD-4LCA/CD-8LCA RJ-61 Cable Connector Pin-Outs ..... 6-51 Table 6-25 PZ-4LCA/PZ-8LCE/ RJ-61 Cable Connector Pin-Outs ....6-55 Table 6-26 CD-LTA Maximum Capacities ............6-57 Table 6-27 CD-LTA LED Indications ..............6-58 Table 6-28 CD-LTA RJ11 Cable Connector Pin-Outs ........6-59 Table 6-29 CD-4COTC LED Indications .............
  • Page 55 UNIVERGE SV8100/SV8300 Issue No. 1.5 Table 7-4 Terminal and Tenkey Kit Compatibility ..........7-4 Table 7-5 Terminal and Optional Equipment Compatibility ........ 7-5 Table 7-6 Numbered Keypad Type ..............7-28 Table 7-7 Keypad Kit Type ................7-29 Table 7-8 Line Key Kit Type ................7-30 Table 7-9 Numbered Keypad Type ..............
  • Page 56 Issue No. 1.5 UNIVERGE SV8100/SV8300 THIS PAGE INTENTIONALLY LEFT BLANK xliv List of Tables...
  • Page 57: General Information

    Introduction to SV8100/SV8300 ENERAL NFORMATION ECTION The SV8100/SV8300 is a full-featured IP based communications system providing a rich feature set of existing system, with pure Voice over IP (VoIP) communications, across corporate Local and Wide Area Networks (LAN and WAN). The DT700 series telephones provide a converged infrastructure at the desktop, with a 10Base-T/100Base-TX connection to the LAN and built-in hub for a PC connection to the telephone itself.
  • Page 58: Figure 1-1 Simplified Sv8100 System Connectivity

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Figure 1-1 Simplified SV8100 System Connectivity Figure 1-2 Simplified SV8300 System Connectivity 1 - 2 Introduction to SV8100/SV8300...
  • Page 59 UNIVERGE SV8100/SV8300 Issue No. 1.5 Highlights of the UNIVERGE SV8100/SV8300 are as follows: Pure IP System Capable TDM Configuration The SV8100/SV8300 supports both pure IP switching (peer-to-peer connections) and Time Division Switching. The pure IP switching is provided for communications between DT700 series telephones and for CCIS / Remote Unit connections with other SV8100/SV8300/SV7000.
  • Page 60: Equipment List

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Universal Blade Slot (19” Chassis) A 19” Chassis is used for legacy line/trunk blades. One 19” Chassis provides six universal slots and one expansion slot. Also, the universal slots can be used for special application blades without complicated limitation. This makes easy quotation and installation.
  • Page 61: Table 1-2 Chassis Installation Equipment List

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Table 1-2 Chassis Installation Equipment List Stock Number Equipment Name Equipment Description Product Code 4422002 CHS BASE UNIT Floor Mount Set for all chassis (CHS1U-AU SV8100/SV8300 and CHS2U-AU) 4422006 CHS2U BLANK SLOT COVER Blank Slot Cover Set...
  • Page 62: Table 1-4 Blade Equipment List

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Table 1-4 Blade Equipment List Stock Number Equipment Name Abbreviations Equipment Description Product Code 4421004 CD-CP00-AU Main Processor Blade for SV8100 SV8100 4420005 CC-CP00 Main Processor Blade for SV8300 SV8300 4422014 PZ-BS10 BUS0 Expansion Chassis Interface Unit, 3-jack...
  • Page 63: Table 1-5 Cable Equipment List

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Table 1-5 Cable Equipment List Stock Number Equipment Name Equipment Description Product Code 4420007 CHS1U BATT CA INT BATT CHS1U-AU Battery cable for internal battery SV8300 Cable – 10.63ln/270mm 4420008 RS CONSOLE CA-A MAT (PCPro) Cable 6.6 ft. (2.0m)
  • Page 64: Table 1-8 Dt300/Dt700 Series Optional Equipment List

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Table 1-8 DT300/DT700 Series Optional Equipment List Stock Number Equipment Name Equipment Description Product Code 4424017 APR-L( ) UNIT Analog Port Ringer SV8100 4424018 ADA-L( ) UNIT Ancillary Device Adapter SV8100 4424019 BHA-L UNIT Bluetooth® Hub Adapter...
  • Page 65 UNIVERGE SV8100/SV8300 Issue No. 1.5 Table 1-8 DT300/DT700 Series Optional Equipment List (Continued) Stock Number Equipment Name Equipment Description Product Code 4424025 BS (S)-L( ) (BK) KIT Spanish Keypad SV8100/SV8300 4424026 BS (ACD)-L( ) (BK) KIT ACD Support Keypad SV8100/SV8300...
  • Page 66 Issue No. 1.5 UNIVERGE SV8100/SV8300 - - NOTES - - 1 - 10 Introduction to SV8100/SV8300...
  • Page 67: Chapter 2 Sv8100 System Specifications

    SV8100 System Specifications ENERAL NFORMATION ECTION This chapter provides detailed specifications for the SV8100 system technician. The technician should review this information carefully before installing the system. YSTEM LOCK IAGRAM ECTION Figure 2-1 SV8100 System Block Diagram shows the Blades that can be installed in the chassis and the number of channels supported when the Blade is installed.
  • Page 68 Issue No. 1.5 UNIVERGE SV8100/SV8300 Table 2-1 List of Abbreviations (Continued) Abbreviation Description Intermediate Distribution Frame IP Trunk (P2P CCIS) (on CPU) ISDN Integrated Service Digital Network Local Area Network Single Line Telephone Interface Blade LCDB Expansion Single Line Telephone Interface Blade on LC...
  • Page 69 UNIVERGE SV8100/SV8300 Issue No. 1.5 Figure 2-1 SV8100 System Block Diagram System Hardware Manual 2 - 3...
  • Page 70: Maximum System Capacities

    Issue No. 1.5 UNIVERGE SV8100/SV8300 AXIMUM YSTEM APACITIES ECTION The CHS2U-AU/EU/OT/US is a compact 19” chassis that has six universal slots, one expansion slot and one MPS7101 (power supply unit). When the CD-CP00-AU/EU/ OT/US is installed in the first CHS2U-AU/EU/OT/US, it is referred to as the Controlling Chassis.
  • Page 71: System Configuration - Sv8100

    UNIVERGE SV8100/SV8300 Issue No. 1.5 System Configuration – SV8100 The SV8100 19” chassis provides 104 total ports (80 digital terminals) and can be expanded, using three additional 19” chassis, for a maximum of 416 ports (320 digital terminals). Through IP connection and use of additional 19”...
  • Page 72: Table 2-3 Sv8100 Maximum System Capacities - Chassis

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Table 2-3 SV8100 Maximum System Capacities – Chassis shows the maximum number of chassis and related equipment that can be installed in a system. Table 2-3 SV8100 Maximum System Capacities – Chassis 19” 19” 19”...
  • Page 73 UNIVERGE SV8100/SV8300 Issue No. 1.5 Table 2-4 SV8100 Maximum System Capacities – Blades 19” 19” 19” Chassis Hardware Chassis Chassis without Networked with CPU Comments Chassis Number of Slot(s) for Interface 5 Slots 6 Slots 23 Slots Package Common Control Blades: CD-CP00-AU/EU/OT/US –...
  • Page 74 Issue No. 1.5 UNIVERGE SV8100/SV8300 Table 2-4 SV8100 Maximum System Capacities – Blades (Continued) 19” 19” 19” Chassis Hardware Chassis Chassis without Networked with CPU Comments Chassis Number of Slot(s) for Interface 5 Slots 6 Slots 23 Slots Package Trunk Blades: CD-2BRIA –...
  • Page 75: Licensing

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Table 2-5 Daughter Board Combinations shows each blade and associated daughter board combinations. The daughter boards that can be mounted on specific blades are indicated by a checkmark. For example, the CD-LTA can have a PZ-2BRIA or the PZ-4COTG daughter board mounted.
  • Page 76 This License is NOT REQUIRED to support the CCISOIP Trunking Feature. LK-SYS-IP-TERMINAL-1-LIC NEC SIP Client - One license One NEC SIP Client - supports NEC MLT SIP Terminal and/or NEC Softphone (SP310). LK-SYS-IP-TERMINAL-4-LIC NEC SIP Client - Four license Four NEC SIP Client - supports NEC MLT SIP Terminal and/or NEC Softphone (SP310).
  • Page 77 UNIVERGE SV8100/SV8300 Issue No. 1.5 Table 2-6 System Licenses (Continued) License Function Description Voice Mail and Unified Messaging: LKS-VM-VRS2-LIC VRS Port - Two license Two Port License VRS – supports general message, personal greeting, Automated Attendant, ACD messages. Supports a maximum 16 dynamic VRS ports and/or eight dynamic InMail ports.
  • Page 78 Issue No. 1.5 UNIVERGE SV8100/SV8300 Table 2-6 System Licenses (Continued) License Function Description LKS-UMS-CLIENT16-LIC UM8000 Mail View App 16 Client View App Session UMS8000 Mail. Supports client, Session - 16 license View Mail, View Call Plus, VMM (outlook), VML (Lotus Notes), VMG (GroupWise) and Web Mailbox Manager.
  • Page 79 (SP310) Client - One license in conjunction with NEC Desktop Suite (Assistant, Attendant, SOFTPHONE1-LIC SP310) Stock No. 4421015 SV8100 Application CD. The NEC Softphone SP310 requires a NEC SIP Client License stock number 670716 LK-SYS-IP-TERMINAL-1-LIC. LKS-DESKTOP SUITE- Desktop Suite Soft Phone...
  • Page 80: Table 2-7 Board Power Factor

    OWER ASED ALCULATOR HART ECTION The UNIVERGE SV8100 system uses two types of power factors. For a single chassis chart refer to Table 2-7 Board Power Factor. For the maximum number of specific blades per package, see Table 2-8 Maximum Number of Package Installed.
  • Page 81: Table 2-10 Ip Terminal Power Chart

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Table 2-9 Terminal Power Factor Terminal Power Factor 19 inch Chassis =<80 Item Power Factor DTL-24D-1( ) TEL DTL-8LD-1( ) TEL BHA-L( ) UNIT ADA-L( ) UNIT APR-L( ) UNIT BCH-L( ) (BK) UNIT PSA-L( )
  • Page 82: System Requirements And Specifications

    Issue No. 1.5 UNIVERGE SV8100/SV8300 YSTEM EQUIREMENTS AND PECIFICATIONS ECTION Cabling This section provides cabling requirements and specifications for various equipment used in the SV8100 system. Figure 2-3 Connecting the DLC Using Twisted 2-Pair Cable is a diagram of the...
  • Page 83 UNIVERGE SV8100/SV8300 Issue No. 1.5 Table 2-13 DT700 Series Loop Resistance and Cable Length Terminal or Adapter Ethernet Cable ITL-2E-1( ) (BK) TEL Cat 5/Cat 6 Ethernet 328.1 ft (100m) ITL-6DE-1( ) (BK) TEL Cat 5/Cat 6 Ethernet 328.1 ft (100m) ITL-8LD-1( ) (BK) TEL Cat 5/Cat 6 Ethernet 328.1 ft (100m)
  • Page 84: Power Requirements

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Power Requirements A dedicated 50 Hz circuit located within seven feet of the chassis is 240VAC required. A separate dedicated outlet for each chassis should be installed. Double Pole/Neutral Fusing (power supply fuses are located at both the L and N side).
  • Page 85: Power Supply Consumption

    UNIVERGE SV8100/SV8300 Issue No. 1.5 A dedicated outlet, separately fused and grounded for each chassis should be installed. Double Pole/Neutral Fusing (power supply fuses are located at both the L and N side). 6.2.2 Power Supply Consumption Table 2-17 Power Consumption...
  • Page 86: Outside Line Types

    Operating Humidity: 20 ~ 95% RH (non-condensing) Recommended Long Term Humidity: 10 ~ 95% RH Outside Line Types The following outside lines can be used with the UNIVERGE SV8100/SV8300 system. 2-wire, Loop Start or Ground Start Trunks 2-wire, 2-way DID Lines (Dial Pulse or DTMF) DID feature is not available for Europe and Australia market.
  • Page 87: Network

    Network Time Division Multiplexing (TDM) allows transmission of data and voice simultaneously over one communications medium. The specifications that the UNIVERGE SV8100/SV8300 system uses for switching, clock, data bus, and timeframe are shown below. TDM Switching: PCM (µ Law/A-Law) TDM Clock: 2.048 MHz TDM Data Bus: 8 bit TDM Timeframe: 125 µs.
  • Page 88: Dialing Specifications

    Dial Pulse Address Signaling uses dial pulses (regular momentary interruptions) to signal the equipment. The following Dial Pulse specifications are used in the UNIVERGE SV8100/SV8300 system. Pulse Rate: 10 ± 0.5 pps/20 ± 1.0 pps Percent Break: 60 ± 1.5% Interdigit Interval: 0 pps/20 pps 770 ms.
  • Page 89: External Equipment Connection

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Duration of Dual Frequency Signal: 110 ms. default/60 ms. minimum Interdigital Time: 140 ms. default/45 ms. minimum Nominal High Group Frequencies (Hz) 1209 1336 1477 Nominal Low Group Frequencies (Hz) 6.6.3 External Equipment Connection Door Phone or TV Door Phone...
  • Page 90: Pc Connection

    6.6.9 Relay Contact All Relay Contact Ratings: 500 mA, 24Vdc Battery Backup The UNIVERGE SV8100/SV8300 system has battery backup functions for system backup and for memory backup. 6.7.1 System Backup (Optional) During a power failure, the system can be backed up using the CHS2U BATT MTG KIT for a backup time of 10 minutes or one of the CHS LARGE BATTs for a backup time ranging from 45~180 minutes.
  • Page 91: Weights And Dimensions

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Weights and Dimensions Table 2-18 SV8100 Weights and Dimensions on page 2-25 shows the shipping weight, height, width and depth of each SV8100 digital multiline terminal, IP term multiline terminal, D , Series i multiline terminal, chassis, assorted blades and adapters.
  • Page 92 Issue No. 1.5 UNIVERGE SV8100/SV8300 Table 2-18 SV8100 Weights and Dimensions (Continued) Shipping Unit Height Width Depth Weight CD-4LCA 5.99 oz 0.98 in 9.45 in 7.68 in (0.17 kg) (25 mm) (240 mm) (195 mm) PZ-4LCA 3.10 oz 0.60 in 9.45 in...
  • Page 93 UNIVERGE SV8100/SV8300 Issue No. 1.5 Table 2-18 SV8100 Weights and Dimensions (Continued) Shipping Unit Height Width Depth Weight Digital Multiline Terminal DTL-2E-1( ) (BK) TEL 35.27 oz 4.41 in 7.05 in 8.86 in (1.0 kg) (112 mm) (179 mm) (225 mm) DTL-6DE-1( ) (BK) TEL 38.8 oz...
  • Page 94: Tone Patterns

    Tone Patterns Table 2-19 Tone Patterns lists the frequency and the pattern for the tones. Tones are used to inform UNIVERGE SV8100/SV8300 station users of system functions such as dial tone, busy tone, or ringback tone. Table 2-19 Tone Patterns...
  • Page 95: Multiline Terminal Led Flash Patterns

    Issue No. 1.5 6.8.2 Multiline Terminal LED Flash Patterns The UNIVERGE SV8100/SV8300 system has several colored LEDs installed. Green is used primarily for I-Use conditions and for outside calls. Red is used primarily for Other Use conditions and internal calls.
  • Page 96: Traffic Capacity

    Issue No. 1.5 UNIVERGE SV8100/SV8300 RAFFIC APACITY ECTION Table 2-21 Traffic Capacity provides information about the traffic capacity for the basic system package and expanded system package. Table 2-21 Traffic Capacity Basic System Expanded System Traffic Capacity Package Package Traffic Capacity...
  • Page 97: Chapter 3 Sv8300 System Specifications

    SV8300 System Specifications ENERAL NFORMATION ECTION This chapter provides detailed specifications for the SV8300 system technician. The technician should review this information carefully before installing the system. YSTEM LOCK IAGRAM ECTION Figure 3-1 SV8300 System Block Diagram shows the Blades that can be installed in the chassis and the number of channels supported when the Blade is installed.
  • Page 98 Issue No. 1.5 UNIVERGE SV8100/SV8300 Table 3-1 List of Abbreviations (Continued) Abbreviation Description Device Registration Server (on CPU) Direct Station Selection Console Digital Trunk Interface Digital Tone Generator (on CPU) ETHERNET Ethernet Port (on CPU) EX IN/EX OUT Unit Synchronization Port (IN/OUT) (on CPU)
  • Page 99 UNIVERGE SV8100/SV8300 Issue No. 1.5 Table 3-1 List of Abbreviations (Continued) Abbreviation Description RS1/RS2 Serial Port (on CPU) Single Line Telephone SMDR Station Message Detail Recording SWHUB Power over Ethernet Hub TDSW Time Division Switch (on CPU) VM00 In-Skin UMS Blade...
  • Page 100 Issue No. 1.5 UNIVERGE SV8100/SV8300 Figure 3-1 SV8300 System Block Diagram 3 - 4 SV8300 System Specifications...
  • Page 101: Maximum System Capacities

    UNIVERGE SV8100/SV8300 Issue No. 1.5 AXIMUM YSTEM APACITIES ECTION The CD-CP00-AU/EU/OT/US is a single slot, 19” chassis holding the CC-CP00 blade and one PSU. The CD-CP00-AU/EU/OT/US can be expanded by adding a maximum of three additional CHS2U-AU/EU/OT/US chassis (referred to as a Unit), increasing the capacity of the system to meet the customer’s business needs.
  • Page 102 Issue No. 1.5 UNIVERGE SV8100/SV8300 Table 3-2 SV8300 Maximum System Capacity (Continued) 1 Unit Units Units Units System Maximum Item Remote Standalone Unit Central Office Trunk Tie Line Trunk E&M BRI Trunk Physical PRI (23B+D) Trunk Port PRI (30B+D) Trunk...
  • Page 103: System Configuration - Sv8300

    UNIVERGE SV8100/SV8300 Issue No. 1.5 System Configuration – SV8300 The SV8300 consists of a CD-CP00-AU/EU/OT/US chassis and CHS2U-AU/ EU/OT/US chassis depending on the system configuration. The CC-CP00 blade in the CD-CP00-AU/EU/OT/US chassis can control a maximum of three CHS2U-AU/EU/OT/US Chassis, collectively called a UNIT. The SV8300 can be configured for a maximum of four UNITs.
  • Page 104: Table 3-3 Maximum System Capacity - Chassis

    Issue No. 1.5 UNIVERGE SV8100/SV8300 SV8300 (Main Unit) SV8300 SV8300 SV8300 (Remote Unit 1) (Remote Unit N) (Remote Unit 2) Maximum of 46 Remote Unit per System Maximum of 2048 ports per System (Maximum of 324 ports per Remote Unit) Figure 3-4 System Configuration Example (Remote Unit Over IP System) Table 3-3 Maximum System Capacity –...
  • Page 105: Table 3-4 Sv8300 Maximum System Capacities - Blades

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Table 3-3 Maximum System Capacity – Chassis (Continued) 1 Unit 2 Units 3 Units 4 Units System Maximum Equipment Remote 2Ux1 2Ux2 2Ux3 2Ux6 2Ux9 2Ux12 Standalone Unit 45 minutes LARGE backup BATT BOX 3 hours backup...
  • Page 106 Issue No. 1.5 UNIVERGE SV8100/SV8300 Table 3-4 SV8300 Maximum System Capacities – Blades 1 Unit 2 Units 3 Units 4 Units System Maximum Equipment Remote 2Ux 6 2Ux 9 2Ux 12 Standalone Unit Common Control Blades: CC-CP00 PZ-64IPLA PZ-128IPLA PZ-VM21...
  • Page 107: Table 3-5 Daughter Board Combinations

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Table 3-5 Daughter Board Combinations shows each blade and associated daughter board combinations. The daughter boards that can be mounted on specific blades are indicated by a checkmark. For example, the CD-4COTB can have a PZ-4COTF daughter board mounted.
  • Page 108: Table 3-7 Maximum System Capacity - Optional Equipment

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Table 3-7 Maximum System Capacity – Optional Equipment shows the maximum number of optional equipment that can be installed in a system. Table 3-7 Maximum System Capacity – Optional Equipment 1 Unit System Maximum Units...
  • Page 109: Licensing

    UNIVERGE SV8100/SV8300 Issue No. 1.5 ICENSING ECTION Table 3-9 System Licenses provides a list of the licensing available with the system. Table 3-9 System Licenses Category License Description System LS-SYS-PORT CAPACITY-LIC Port Capacity LS-SYS-IPPAD16-LIC VoIP Channels (VoIPDB) LS-SYS-R1-LIC System Version License R1...
  • Page 110: Table 3-10 Blade Power Factor

    Issue No. 1.5 UNIVERGE SV8100/SV8300 OWER ASED ALCULATOR HART ECTION The SV8300 system used two types of power factors. For a single chassis chart refer Table 3-10 Blade Power Factor. Refer to Table 3-11 Terminal Power Factor below, for the Terminal/Adapter power chart.
  • Page 111: System Requirements And Specifications

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Table 3-11 Terminal Power Factor (Continued) Terminal Power Factor Total = < 80 per 19 inch Chassis Item Power Factor term DSS Console Series i Option Analog Port Adapter without Ringer (APA) Analog Port Adapter with...
  • Page 112 Issue No. 1.5 UNIVERGE SV8100/SV8300 Table 3-12 Cable Length of Terminals Cable Cable Length between Terminal Remarks SV8300 and Terminal Kind of Cable Pair term Twisted Pair Cable 1-pair 1312 ft (400m) with 22 AWG – DT300 Series/ Series i 1968 ft (600m) with 24 AWG –...
  • Page 113: Power Requirements

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Table 3-13 Cable Length of Optional Equipment (Continued) Cable Cable Length between Terminal Remarks SV8300 and Terminal Kind of Cable Pair PGD(2)-U( ) ADP Twisted Pair Cable 1-pair 1968 ft (600m) with 22 AWG 2625 ft (800m) with 24 AWG –...
  • Page 114 Issue No. 1.5 UNIVERGE SV8100/SV8300 With input voltage of 120 VAC and with full load conditions: AC Input I: Controlling Chassis=2.19A, Expansion Chassis=2.19A, total 4.38A VA @ 120V: Controlling Chassis=263 VA, Expansion Chassis= 263 VA, total 526 VA KWh @ AC Input I x 120V/1000: Controlling Chassis=0.263 KWh, Expansion Chassis=0.263 KWh, total 0.526...
  • Page 115: Power Supply Consumption

    UNIVERGE SV8100/SV8300 Issue No. 1.5 6.2.2 Power Supply Consumption AC 100 V power supply: Table 3-14 Power Consumption Maximum Watts Used Watts Used Chassis (Idle) (Maximum) Current Controlling Chassis 0.7A Controlling Chassis + Expansion 2.89A 136W 175W Chassis Controlling Chassis + 2 Expansion 5.08A...
  • Page 116: Outside Line Types

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Humidity: 10 ~ 90% RH (non-condensing) Recommended Long Term Humidity: 10 ~ 90% RH Blades – CD-4LCA, PZ-4LCA, CD-8LCA, PZ-8LCE, CD-4COTA, CD-4COTB, D-4COTC, D-4COTE, PZ-4COTF, PZ-4COTG, CD-PRTA, CD-CCTA Operating Temperature: +32°F ~ +104°F (0°C ~ 40°C) Recommended Long Term Temperature: -4°F ~ +140°F...
  • Page 117: Network

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Data Transmission Rates: Between CD-8DLCA and multiline terminal: 184K bps (voice and signaling) Scanning Time for each multiline terminal: 32 ms. 6.5.2 Network Time Division Multiplexing (TDM) allows transmission of data and voice simultaneously over one communications medium. The specifications that the SV8300 system uses for switching, clock, data bus, and timeframe are shown below.
  • Page 118: Series I Terminals

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Single Line Telephone Nominal Current: 25 mA Ring Signal: 56 Vac RMS @ 20 Hz AP(A)-R Unit Nominal Current: 30 mA AP(R)-R Unit Nominal Current: 30 mA Ring Signal: 56 Vac RMS @ 20 Hz 6.5.5...
  • Page 119 UNIVERGE SV8100/SV8300 Issue No. 1.5 Frequency Deviation: Less than ±1.5% Signal Level: Nominal level per frequency: -6 ~ -4 dBm Minimum level per frequency Low Group: -10 dBm High Group: -8 dBm Maximum level per frequency: 0 dBm Rise Time: Within 5 ms.
  • Page 120 Issue No. 1.5 UNIVERGE SV8100/SV8300 6.6.5 External Paging (Audio) Output Power: –10 dBm Signal Level Ω Output Impedance: 600 Relay Contact Rating: 500 mA, 24 Vdc 6.6.6 External Tone Ringer/Night Chime Output Output Level: –10 dBm Ω Output Impedance: 600 Relay Contact Rating: 500 mA, 24 Vdc 6.6.7...
  • Page 121: Weights

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Weights and Dimensions Table 3-16 SV8300 Weights shows the weight of main equipment for SV8300. Figure 3-6 SV8300 Chassis Dimensions shows the dimension of main equipment for SV8300. 6.8.1 Weights Table 3-16 SV8300 Weights Equipment...
  • Page 122: Dimensions

    Issue No. 1.5 UNIVERGE SV8100/SV8300 6.8.2 Dimensions Controlling Chassis 43 mm (1.7 inch) Expansion Chassis 88 mm (3.5 inch) Figure 3-6 SV8300 Chassis Dimensions UNIT (Controlling Chassis + Expansion Chassis x 3) BASE UNIT Figure 3-7 SV8300 Chassis Dimensions (Controlling and Three Expansion)
  • Page 123: Audible And Visual Indication

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Audible and Visual Indication 6.9.1 Lamp Display Table 3-17 Lamp Display on page 3-27 shows the state of the multiline terminal. Table 3-17 Lamp Display Display State Cycle (second) Turning off Slow blinking 0.25 Blinking 0.25...
  • Page 124: Tone Patterns

    Issue No. 1.5 UNIVERGE SV8100/SV8300 6.9.2 Tone Patterns lists the frequency and the pattern for the tones. Tones are used to inform SV8300 station users of system functions such as dial tone, busy tone, or ringback tone. on page 3-28 lists the frequency and the pattern for the tones.
  • Page 125: Multiline Terminal Led Flash Patterns

    UNIVERGE SV8100/SV8300 Issue No. 1.5 6.9.3 Multiline Terminal LED Flash Patterns The SV8300 system has 2-color LEDs. Green is used primarily for I-Use conditions and for outside calls. Red is used primarily for Other Use conditions and internal calls. Refer to...
  • Page 126: Traffic Capacity

    Issue No. 1.5 UNIVERGE SV8100/SV8300 RAFFIC APACITY ECTION Table 3-20 Traffic Capacity provides information about the traffic capacity for the basic system package and expanded system package. Table 3-20 Traffic Capacity Traffic Capacity (CC-CP00) System Max. 12000 BHCA Traffic Conditions: 2n+m <...
  • Page 127: Chapter 4 Installing The Sv8100 Chassis

    Installing the SV8100 Chassis ENERAL NFORMATION ECTION This chapter contains information to help the technician install the chassis for the SV8100 system. The technician should be familiar with this section before installing any equipment. MDF/IDF C REPARATION AND ONSTRUCTION ECTION Pre-installation planning is essential.
  • Page 128: Surveying The Customer Site

    Chassis are normally rack mounted to protect against accident or flooding. The chassis should not be located directly beneath pipes. Leaks or condensation could damage the UNIVERGE SV8100/SV8300 system equipment. The area where the chassis is located must be free of corrosive...
  • Page 129: Selecting A Permanent Mdf Location

    UNIVERGE SV8100/SV8300 Issue No. 1.5 2.3.2 Selecting a Permanent MDF Location When selecting a permanent site for the MDF, the technician may encounter some of the following conditions: Limited space is available but must be used. The available space may pose one or more environmental hazards.
  • Page 130: Power Failure Transfer

    Issue No. 1.5 UNIVERGE SV8100/SV8300 The system requires a 3-prong dedicated 240 VAC 50 Hz circuit (NEMA 5-15 receptacle) located within 7 feet of the AC receptacle. Telco should install the RJ21X to the right of the Controlling Chassis. Extension blocks should be installed to the left of the Controlling Chassis.
  • Page 131 UNIVERGE SV8100/SV8300 Issue No. 1.5 NSTALLING THE HASSIS ECTION The CHS2U-AU chassis has six universal blade slots for legacy line/trunk blade (Single Line Telephone Interface, Digital multiline terminal Interface, Central Office Trunk, ISDN PRI Interface, etc.), In-skin Application Blades (In-skin UMS, In-Skin Router, etc.).
  • Page 132: Wall Mounting The 19" Chassis

    This allows secure anchoring of the screws which support the weight of the chassis. Due to chassis weight, NEC recommends only a single CHS2U-AU chassis per wall mount. Upper Surface of Wall Mount Bracket Figure 4-3 Wall Mount Spacing Guide (19”...
  • Page 133: Figure 4-4 Install Wall Mount Brackets With Screws

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Mark and drill the six holes required for a wall installation. Align screw holes in wall mount brackets with drilled holes. Using six screws, secure the two wall mount brackets to the wall. Refer to Figure 4-4 Install Wall Mount Brackets with Screws screw location.
  • Page 134: Figure 4-5 Securing Metal Fittings To Chassis With Screws

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Using four screws, secure the metal fittings on the Left and Right sides of the 19” chassis. Refer to Figure 4-5 Securing Metal Fittings to Chassis with Screws for screw location. Figure 4-5 Securing Metal Fittings to Chassis with Screws...
  • Page 135: Figure 4-6 Secure Metal Fitting To Upper Wall Mount Bracket With A Screw

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Align the metal fitting with the upper wall mount bracket. The lower metal fitting will rest against the lower wall mount bracket. Secure the metal fitting and upper wall mount bracket with a single screw (see...
  • Page 136: Figure 4-7 Secure Metal Fitting To Lower Wall Mount Bracket With Screws

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Using two screws, secure the metal fitting to the lower wall mount bracket. Refer to Figure 4-7 Secure Metal Fitting to Lower Wall Mount Bracket with Screws for screw location. Figure 4-7 Secure Metal Fitting to Lower Wall Mount Bracket with...
  • Page 137: Figure 4-8 Attach Cable Support Bracket To Lower Wall Mount Bracket

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Attach the supplied cable support bracket to either end of the lower wall mount bracket with a single screw (refer to Figure 4-8 Attach Cable Support Bracket to Lower Wall Mount Bracket). Figure 4-8 Attach Cable Support Bracket to Lower Wall Mount Bracket...
  • Page 138: Figure 4-9 Attachment Locations Of Cable Support Bracket

    Issue No. 1.5 UNIVERGE SV8100/SV8300 The cable support bracket can be installed any of the four corners of the 19” chassis (refer to Figure 4-9 Attachment Locations of Cable Support Bracket). Figure 4-9 Attachment Locations of Cable Support Bracket Connect the ground wire to all chassis. Refer to 3.5.5 Install 19”...
  • Page 139: Floor Mounting The 19" Chassis

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Floor Mounting the 19” Chassis The CHS2U-AU controlling and expansion chassis can be mounted on the floor using the CHS BASE UNIT and the CHS2U JOINT BRACKET KIT. 3.2.1 CHS2U-AU Chassis Installation Use the template shown in...
  • Page 140: Figure 4-11 Secure Chs Base Unit With Anchor Bolts

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Using anchor bolts, secure the CHS BASE UNIT to the floor. Refer to Figure 4-11 Secure CHS BASE UNIT with Anchor Bolts on page 4-14 for screw location.. Figure 4-11 Secure CHS BASE UNIT with Anchor Bolts Install the five rubber feet to the bottom of the chassis.
  • Page 141: Multiple Chs2U-Au Chassis Installation

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Secure the chassis to the CHS BASE UNIT using eight screws supplied with the CHS2U JOINT BRACKET KIT. Figure 4-13 Install CHS2U JOINT BRACKET KIT Connect the ground wire to all chassis. Refer to 3.5.5 Install 19”...
  • Page 142: Figure 4-15 Install Metal Brackets With Screws

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Using supplied screws in the CHS2U JOINT BRACKET KIT, attach metal brackets to both ends of the 19” chassis and the CHS BASE UNIT. Refer to Figure 4-15 Install Metal Brackets with Screws. Metal Brackets Figure 4-15 Install Metal Brackets with Screws Connect the ground wire to all chassis.
  • Page 143: Stand Mounting The 19" Chassis

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Stand Mounting the 19” Chassis A single or multiple chassis can be stand mounted. Controlling and Expansion chassis can be stand mounted using the CHS2U STAND KIT(K) and CHS2U JOINT BRACKET KIT. 3.3.1 CHS2U-AU Chassis Installation...
  • Page 144: Figure 4-17 Secure Chs2U-Au Chassis To Chs2U Stand Kit With Screws

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Secure the CHS2U-AU chassis to the assembled CHS2U STAND KIT, see Figure 4-17 Secure CHS2U-AU Chassis to CHS2U STAND KIT with Screws on page 4-18. Expansion Plate Figure 4-17 Secure CHS2U-AU Chassis to CHS2U STAND KIT with Screws...
  • Page 145: Figure 4-18 Secure Stand Mount To Floor With Screws

    Figure 4-18 Secure Stand Mount to Floor with Screws on page 4-19). To prevent possible damage to the 19” chassis due to falling, NEC recommends screws be installed in the stand mount brackets as soon as possible. Figure 4-18 Secure Stand Mount to Floor with Screws Connect the ground wire to all chassis.
  • Page 146: Multiple Chs2U-Au Chassis Installation

    Issue No. 1.5 UNIVERGE SV8100/SV8300 3.3.2 Multiple CHS2U-AU Chassis Installation Expansion chassis (maximum of three) can be added to the CHS2U STAND KIT and will require an additional CHS2U JOINT BRACKET KIT per chassis. Install the five rubber feet to the bottom of each chassis.
  • Page 147: Figure 4-21 Install Additional Chs2U Joint Bracket Kit

    Figure 4-21 Install Additional CHS2U JOINT BRACKET KIT). To prevent possible damage to the 19” chassis due to falling, NEC recommends screws be installed in the stand mount brackets as soon as possible. Connect the ground wire to all chassis. Refer to 3.5.5 Install 19”...
  • Page 148: Rack Mounting The 19" Chassis

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Rack Mounting the 19” Chassis A single or multiple chassis can be rack mounted. Controlling and Expansion chassis can be racked mounted by stacking them horizontally. The 19” chassis requires two rack mount brackets per chassis for mounting.
  • Page 149: Figure 4-24 Rack Mount 19" Chs2U-Au

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Repeat for additional chassis mounting. Figure 4-23 Rack Mount Bracket Installed 19” CHS2U-AU Carefully slide the chassis into desired location within the rack. Make sure the hooks on the mounting bracket are inserted into the back of the chassis, securing it in place.
  • Page 150: Installing The 19" Chassis

    Inspect the equipment for any physical damage. If you are not sure about the function of a component, review the associated information within this manual. Contact your authorized NEC Sales Representative if you have additional questions. Note that the chassis does not initially contain any blades.
  • Page 151: Installing Expansion Blades In The 19" Chassis (Optional)

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Align the CD-CP00-AU blade with the Slot 1 guides of the Controlling Chassis. Figure 4-25 19” Controlling Chassis – Guides Slot 1 Slide the CD-CP00-AU blade into the chassis until resistance (back plane) is felt.
  • Page 152: Table 4-3 Pz-Bs10/Pz-Bs11 Connector Pin-Out

    The EXIFU cable connects the Controlling Chassis and its EXIFU-B1 interface to the second, third, and fourth EXIFU-E1 interface. Use only the CAT 5 cables provided by NEC to make the connections between the Controlling and Expansion Chassis. The PZ-BS10 provides:...
  • Page 153: Figure 4-28 Pz-Bs10 Expansion Bay In Controlling Chassis

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Locate the door positioned on the left end (expansion bay) of the Controlling Chassis. Expansion Bay Figure 4-28 PZ-BS10 Expansion Bay in Controlling Chassis From the left side of the chassis, pull cover outward to expose the expansion bay.
  • Page 154: Figure 4-30 Pz-Bs10 Blade Guides

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Align the PZ-BS10 blade with the guides located in the expansion bay. Figure 4-30 PZ-BS10 Blade Guides Figure 4-31 PZ-BS10 Components 4 - 28 Installing the SV8100 Chassis...
  • Page 155: Figure 4-32 Installing Pz-Bs10 Blade In Expansion Bay

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Slide the PZ-BS10 blade into the chassis until resistance (back plane) is felt. Figure 4-32 Installing PZ-BS10 Blade in Expansion Bay Gently push until the blade seats and install the supplied retaining screw. Align the door tabs with hinges and reattach the cover.
  • Page 156: Figure 4-34 Pz-Bs10 Installed (Cover Closed)

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Close the PZ-BS10 cover. Figure 4-34 PZ-BS10 Installed (Cover Closed) 3.5.4.3 Install the PZ-BS11 Expansion Blade in the CHS2U-AU Expansion Chassis For the Expansion Chassis to function, the PZ-BS10 blade must be installed in Controlling Chassis.
  • Page 157: Figure 4-36 Open Expansion Chassis Cover

    UNIVERGE SV8100/SV8300 Issue No. 1.5 From the left side of the chassis, pull cover outward to expose the expansion bay. Figure 4-36 Open Expansion Chassis Cover Pull the cover toward you to remove. Cover must be removed to install PZ-BS11 blade.
  • Page 158: Figure 4-38 Installing Pz-Bs11 Blade In Expansion Chassis

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Slide the PZ-BS11 blade into the chassis until resistance (back plane) is felt. Figure 4-38 Installing PZ-BS11 Blade in Expansion Chassis Gently push until the blade seats and install the supplied retaining screw. Align the door tabs with hinges and reattach the cover.
  • Page 159: Figure 4-40 Pz-Bs11 Installed (Cover Closed)

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Close the PZ-BS11 blade cover. Figure 4-40 PZ-BS11 Installed (Cover Closed) 3.5.4.4 Connect the Controlling and Expansion Chassis Installment of the PZ-BS10 blade and PZ-BS11 blade(s) must be completed prior to installation of the provided (Cat 5) expansion cabling.
  • Page 160: Install 19" Chassis Grounding

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Using the NEC provided CAT5 straight-through cable(s), attach one end to each Expansion Chassis CN2 connector on the PZ-BS11 blade (see Figure 4-42 System Expansion Cabling on page 4-34. Attach the opposite end to the CN2, CN3 or CN4 connector on the PZ-BS10 of the Controlling Chassis.
  • Page 161: Install 19" Grounding On Multiple Chassis (Optional)

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Ground each chassis by connecting a 14 AWG wire from the FG lug on the back side of the chassis to an electrical service ground (such as a cold water pipe). CHS2U-AU FG Lug Figure 4-43 Chassis Grounding Lug 3.5.6...
  • Page 162: Install Ac Power Cords

    Issue No. 1.5 UNIVERGE SV8100/SV8300 3.5.7 Install AC Power Cords Locate the supplied AC power cord and attach to the AC Inlet located on the back of the Controlling Chassis. CHS2U-AU AC Inlet Figure 4-45 Install the AC Power Cord 3.5.8...
  • Page 163: Battery Connection

    UNIVERGE SV8100/SV8300 Issue No. 1.5 ATTERY ONNECTION ECTION There are two types of battery connection to provide battery life in the event of a power failure, the internal battery and an external battery with CHS LARGE BATT BOX. Installing the Internal Batteries An internal battery source using two batteries can be installed using the CHS2U BATT MTG KIT (mounting kit) and CHS2U BATT CA INT (internal cabling).
  • Page 164: Figure 4-48 Removing Access Panel

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Remove access panel containing the fan. Refer to Figure 4-48 Removing Access Panel Figure 4-49 Access Panel Removed. Figure 4-48 Removing Access Panel Figure 4-49 Access Panel Removed 4 - 38 Installing the SV8100 Chassis...
  • Page 165: Figure 4-50 Secure Cable In Support Bracket

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Using tie wraps, secure CHS2U BATT CA INT in cable guide bracket (refer to Figure 4-50 Secure Cable in Support Bracket). Figure 4-50 Secure Cable in Support Bracket With supplied screw, install cable guide in chassis (refer to...
  • Page 166: Figure 4-52 Installing Two Batteries

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Install two 2.3 AH-12V batteries (locally procured) into the CHS2U BATT MTG KIT (refer to Figure 4-52 Installing Two Batteries). The first battery must be installed on the left side, then slid to the right due to an installation tab on the mounting kit.
  • Page 167: Figure 4-54 Connecting Chs2U Batt Ca Int

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Connect CHS2U BATT CA INT to battery connector (refer to Figure 4-54 Connecting CHS2U BATT CA INT). Figure 4-54 Connecting CHS2U BATT CA INT Install CHS2U BATT MTG KIT into CHS2U-AU chassis and tighten the...
  • Page 168: Installing The External Batteries

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Reinstall access panel containing the fan and secure with supplied screw (refer to Figure 4-56 Installing the Access Panel). Figure 4-56 Installing the Access Panel Connect grounding and AC power cable. Installing the External Batteries An optional (locally procured), external battery source can be used to provide power in the event of a power failure.
  • Page 169: Floor Mounting The Chs Large Batt Box

    UNIVERGE SV8100/SV8300 Issue No. 1.5 4.2.1 Floor Mounting the CHS LARGE BATT BOX Because of injury from falling equipment, wall mounting the CHS LARGE BATT BOX is not recommended. Mounting the CHS LARGE BATT BOX directly on the floor is not recommended.
  • Page 170: Battery Installation

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Align and install the CHS LARGE BATT BOX on top of the CHS BASE UNIT. Refer to Figure 4-58 Installing the CHS LARGE BATT BOX using the CHS2U JOINT BRACKET KIT on page 4-44. Figure 4-58 Installing the CHS LARGE BATT BOX using the CHS2U JOINT BRACKET KIT Secure the CHS LARGE BATT BOX to the CHS BASE UNIT using the CHS2U JOINT BRACKET KIT.
  • Page 171: Figure 4-60 Removing Battery Tray Suppressor

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Remove two screws from front of Battery Tray Suppressor. Refer to Figure 4-60 Removing Battery Tray Suppressor. Figure 4-60 Removing Battery Tray Suppressor Slide Battery Tray Suppressor outward to remove. Slide Battery Tray(s) out of CHS LARGE BATT BOX.
  • Page 172: Figure 4-62 Removing Battery Tray Bracket

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Remove two screws and remove the Battery Tray Bracket. Refer Figure 4-62 Removing Battery Tray Bracket. Figure 4-62 Removing Battery Tray Bracket Refer to Figure 4-63 Battery Cable Connection Guide connection of battery cable to battery terminals. Repeat for additional battery connection.
  • Page 173: Figure 4-64 Installing Battery Connection Cable

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Using two screws, install the Battery Tray Bracket. Refer to Figure 4-62 Removing Battery Tray Bracket on page 4-46. Figure 4-64 Installing Battery Connection Cable Insert Battery Connection Cable into cable guides. Refer to Figure 4-64 Installing Battery Connection Cable on page 4-47.
  • Page 174: Chs Large Batt Box To Chs2U-Au Connection

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Plug the Battery Connection Cable(s) into the Fuse Unit. Refer Figure 4-65 Connecting Battery Cables on page 4-48. Figure 4-65 Connecting Battery Cables Insert tabs on cover into holes on CHS LARGE BATT BOX. Slide the cover left until seated and tighten the screw.
  • Page 175: Figure 4-67 Removing Fan Access Panel

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Remove fan access panel from rear of CHS2U-AU chassis. Refer to Figure 4-67 Removing Fan Access Panel. Figure 4-67 Removing Fan Access Panel Connect one end of Battery Connection Cable to Battery Connector on rear of Basic and Expansion chassis.
  • Page 176: Figure 4-69 Single Chs Large Batt Box Connection

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Connect other end of cable to Battery Connector on rear of CHS LARGE BATT BOX chassis. Refer to Figure 4-69 Single CHS LARGE BATT BOX Connection Figure 4-70 Dual CHS LARGE BATT BOX Connection. Basic...
  • Page 177: Chs Large Batt Box Fuse Replacement

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Insert the access panel tab into the rear of the CHS1U-AU chassis running the Battery Connection Cable through the cutout. Secure panel with the retaining screw. Refer to Figure 4-71 Install the Fan Access Panel.
  • Page 178: Figure 4-73 Removing Battery Tray Suppressor

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Remove two screws from front of Battery Tray Suppressor. Refer to Figure 4-73 Removing Battery Tray Suppressor. Figure 4-73 Removing Battery Tray Suppressor Slide Battery Tray Suppressor outward to remove. Disconnect the Battery Connection Cables from the Fuse Unit.
  • Page 179: Figure 4-65 Connecting Battery Cables

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Figure 4-75 CHS LARGE BATT BOX Fuse Unit Slide the Fuse Unit into the and tighten the two screws (refer to Figure 4-74 Disconnecting Battery Cables on page 4-52). Plug the Battery Connection Cables into the Fuse Unit. Refer to Figure 4-76 Connecting Battery Cables on page 4-53.
  • Page 180: Power Supply

    Figure 4-77 Installing Cover Battery OWER UPPLY ECTION Do not attempt to replace the power supply. The MPS7101 is not a field replaceable part. If the power supply fails contact NEC. EMOVE AND NSTALL OOLING ECTION If required, the cooling fan installed in the CHS2U-AU chassis can be removed and replaced.
  • Page 181: Figure 4-78 19" Chassis Access Panel

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Loosen retaining screw from chassis access panel. Retaining Screw Figure 4-78 19” Chassis Access Panel Swing access panel outward and unplug fan power cable. See Figure 4-79 Opening Chassis Access Panel (19” Chassis). Fan Power Cable Plug Figure 4-79 Opening Chassis Access Panel (19”...
  • Page 182: Install Cooling Fan

    Issue No. 1.5 UNIVERGE SV8100/SV8300 6.1.2 Install Cooling Fan Align replacement fan with holes and secure with two screws (refer to Figure 4-80 Chassis Access Panel Removed (19” Chassis) on page 4-55. Install cabling into retention clips (refer to Figure 4-80 Chassis Access Panel Removed (19”...
  • Page 183 UNIVERGE SV8100/SV8300 Issue No. 1.5 - - NOTES - - System Hardware Manual 4 - 57...
  • Page 184 Issue No. 1.5 UNIVERGE SV8100/SV8300 - - NOTES - - 4 - 58 Installing the SV8100 Chassis...
  • Page 185: General Information

    Installing the SV8300 Chassis ENERAL NFORMATION ECTION This chapter contains information to help the technician install the chassis for the SV8300 system. The technician should be familiar with this section before installing any equipment. MDF/IDF C REPARATION AND ONSTRUCTION ECTION Pre-installation planning is essential.
  • Page 186: Surveying The Customer Site

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Although it is recommended to install the blades with the system power off, all blades can be installed hot, except for the following: CC-CP00 PZ-BS10 and PZ-BS11 PZ-64IPLA and PZ-128IPLA PZ-VM21 Surveying the Customer Site...
  • Page 187: Selecting A Permanent Mdf Location

    UNIVERGE SV8100/SV8300 Issue No. 1.5 2.3.2 Selecting a Permanent MDF Location When selecting a permanent site for the MDF, the technician may encounter some of the following conditions: Limited space is available but must be used. The available space may pose one or more environmental hazards.
  • Page 188: Power Failure Transfer

    Issue No. 1.5 UNIVERGE SV8100/SV8300 The system requires a 3-prong dedicated 110 VAC 60 Hz circuit (NEMA 5-15 receptacle) located within 7 feet of the AC receptacle. Telco should install the RJ21X to the right of the Controlling Chassis. Extension blocks should be installed to the left of the Controlling Chassis.
  • Page 189: Installing The Chassis

    UNIVERGE SV8100/SV8300 Issue No. 1.5 NSTALLING THE HASSIS ECTION There are two types of chassis, the 19” CHS1U-AU chassis and the 19” CHS2U-AU chassis. The CHS1U-AU chassis mounts the CC-CP00 blade, PZ-BS10 for the CHS2U-AU chassis expansion, PZ-PW146(1U) Power Supply and Cooling FAN.
  • Page 190: Figure 5-3 Chs2U-Us Chassis (Front View)

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Universal Slot for Legacy Line/Trunk blades and Application blades (six slots) Slot for PZ-BS10/PZ-BS11 blade – Connection with CHS2U-AU Power Supply Unit Figure 5-3 CHS2U-US Chassis (Front View) Internal Battery Fan Unit (inside of cover)
  • Page 191: Wall Mounting The 19" Chassis

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Wall Mounting the 19” Chassis When wall mounting the chassis, ensure the wall can support the weight of the chassis (31 lbs per system chassis including blades, cords, power supply, etc.). The chassis is secured to the wall with a wall mount bracket. Ensure that enough space is available to allow the installation of additional expansion chassis.
  • Page 192 Issue No. 1.5 UNIVERGE SV8100/SV8300 Upper Surface of Wall Mount Figure 5-5 Wall Mount Spacing Guide (19” Chassis) 5 - 8 Installing the SV8300 Chassis...
  • Page 193: Figure 5-6 Drilling Instructions For Anchor Bolt

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Mark and drill the six holes required for a wall installation. Drilling: Make a preliminary hole in the concrete, using a drill bit for small- diameter holes. Drill a hole in the concrete with a drill suitable for a plug bolt a little deeper than the plug bolt length.
  • Page 194: Figure 5-7 Securing Wall Mount Brackets With Screws

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Using six screws, secure the two wall mount brackets to the wall. Refer to Figure 5-7 Securing Wall Mount Brackets with Screws for screw location. Figure 5-7 Securing Wall Mount Brackets with Screws 5 - 10...
  • Page 195: Figure 5-8 Installing Metal Fittings With Screws

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Using four screws, secure the metal fittings on the Left and Right sides of the 19” chassis. Refer to Figure 5-8 Installing Metal Fittings with Screws for screw location. Figure 5-8 Installing Metal Fittings with Screws Install five rubber feet on bottom of CHS1U-AU chassis.
  • Page 196: Figure 5-9 Install Joint Brackets With Screws

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Align CHS1U-AU and CHS2U-AU chassis. Secure the two chassis together with a joint bracket and four screws on both sides of the chassis. Refer to Figure 5-9 Install Joint Brackets with Screws for bracket location.
  • Page 197: Figure 5-10 Secure Metal Fitting To Upper Wall Mount Bracket With A Screw

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Align the metal fitting with the upper wall mount bracket. The lower metal fitting will rest against the lower wall mount bracket. Secure the metal fitting and upper wall mount bracket with a single screw (see...
  • Page 198: Figure 5-11 Attachment Locations Of Cable Support Bracket

    Issue No. 1.5 UNIVERGE SV8100/SV8300 The cable support bracket can be installed any of the four corners of the 19” chassis (refer to Figure 5-11 Attachment Locations of Cable Support Bracket). Figure 5-11 Attachment Locations of Cable Support Bracket 5 - 14...
  • Page 199: Figure 5-12 Attach Cable Support Bracket To Lower Wall Mount Bracket

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Attach the supplied cable support bracket to either end of the lower wall mount bracket with a single screw (refer to Figure 5-12 Attach Cable Support Bracket to Lower Wall Mount Bracket). Figure 5-12 Attach Cable Support Bracket to Lower Wall Mount Bracket...
  • Page 200: Figure 5-13 Chs1U-Au And Chs2U-Au Chassis Wall Mounted

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Figure 5-13 CHS1U-AU and CHS2U-AU Chassis Wall Mounted Connect the ground wire to all chassis. Refer to 3.5.7 Install 19” Chassis Grounding on page 5-45 for complete details on grounding the system. Refer to 3.5 Installing the 19” Chassis on page 5-33...
  • Page 201: Floor Mounting The 19" Chassis

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Floor Mounting the 19” Chassis The CHS1U-AU controlling and the CHS2U-AU expansion chassis can be mounted on the floor using the CHS BASE UNIT and the CHS2U JOINT BRACKET KIT. 3.2.1 CHS1U-AU Chassis Installation Position the CHS BASE UNIT on desired surface and mark four...
  • Page 202: Figure 5-14 Chs Base Unit

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Install the five rubber feet to the bottom of the chassis. Figure 5-16 Install Rubber Feet (19” Chassis) Position the CHS1U-AU and CHS2U-AU chassis on top of the CHS BASE UNIT. Secure the chassis to the CHS BASE UNIT using screws supplied with the CHS STAND KIT (K).
  • Page 203: Multiple Chs2U-Au Chassis Installation

    UNIVERGE SV8100/SV8300 Issue No. 1.5 3.2.2 Multiple CHS2U-AU Chassis Installation Expansion chassis can be secured to the CHS BASE UNIT and will require an additional CHS2U JOINT BRACKET KIT per chassis. Install the five rubber feet to the bottom of each chassis.
  • Page 204: Stand Mounting The 19" Chassis

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Stand Mounting the 19” Chassis The SV8300 can be stand mounted. Controlling and Expansion chassis can be stand mounted using the CHS STAND KIT (K), the CHS2U STAND KIT (EXT) and the CHS2U JOINT BRACKET KIT.
  • Page 205: Figure 5-21 Attach Rubber Feet To Chs2U-Us Chassis

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Install the five rubber feet to the bottom of each chassis. Figure 5-21 Attach Rubber Feet to CHS2U-US Chassis Align CHS1U-AU chassis and CHS2U-AU chassis. Secure the two chassis together with a joint bracket and four screws on top sides of the chassis.
  • Page 206: Figure 5-23 Assemble Stand Mount With Screws

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Using supplied screws, assemble the CHS STAND KIT (K). Refer to Figure 5-23 Assemble Stand Mount with Screws. Expansi Figure 5-23 Assemble Stand Mount with Screws Using supplied screws, secure the chassis to the assembled CHS STAND KIT (K).
  • Page 207: Figure 5-25 Chs2U-Au/Chs1U-Au Chassis Stand Mount

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Align screw holes in floor mount bracket with pre-drilled holes in floor. Using supplied screws, secure the CHS STAND KIT (K) to the floor. Refer to Figure 5-25 CHS2U-AU/CHS1U-AU Chassis Stand Mount on page 5-23.
  • Page 208: Chs1U-Au+Chs2U-Auxn Chassis Installation

    Issue No. 1.5 UNIVERGE SV8100/SV8300 3.3.2 CHS1U-AU+CHS2U-AUxN Chassis Installation Expansion chassis (maximum of three) can be added to create a UNIT and will require an additional CHS2U STAND KIT (EXT) per chassis. Using the spacing guide shown below, mark two holes to be drilled.
  • Page 209: Figure 5-27 Attach Rubber Feet To Chs2U-Us Chassis

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Mark and drill the two holes required for a floor installation. Install the five rubber feet to the bottom of each chassis. Figure 5-27 Attach Rubber Feet to CHS2U-US Chassis Align CHS1U-AU chassis and CHS2U-AU chassis. Secure the chassis together with a joint bracket on top sides of the chassis.
  • Page 210: Figure 5-29 Assemble Stand Mount With Screws (Chs1U-Au+Chs2U-Aux3 Configuration)

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Expansio Screws Figure 5-28 Assemble Stand Mount with Screws (CHS1U-AU+CHS2U-AUx2 Configuration) 3.3.2.2 CHS1U-AU+CHS2U-AUx3 Stand Mount Assembly Using supplied screws, assemble the CHS STAND KIT (K) and CHS2U STAND KIT (EXT). Refer to Figure 5-29 Assemble Stand Mount with Screws...
  • Page 211: Figure 5-30 Attach Stand Mount Brackets To Chassis With Screws (Chs1U-Au+Chs2U-Aux2 Configuration)

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Using supplied screws, secure the chassis to the assembled CHS STAND KIT (K). Refer to Figure 5-30 Attach Stand Mount Brackets to Chassis with Screws (CHS1U-AU+CHS2U-AUx2 Configuration) for screw location. 3.3.2.3 CHS1U-AU+CHS2U-AUx2 Install Chassis Using supplied screws, secure the chassis to the assembled CHS STAND KIT (K).
  • Page 212: Figure 5-31 Attach Stand Mount Brackets To Chassis With Screws (Chs1U-Au+Chs2U-Aux3 Configuration)

    Issue No. 1.5 UNIVERGE SV8100/SV8300 3.3.2.4 CHS1U-AU+CHS2U-AUx3 Install Chassis Using supplied screws, secure the chassis to the assembled CHS STAND KIT (K). Refer to Figure 5-31 Attach Stand Mount Brackets to Chassis with Screws (CHS1U-AU+CHS2U-AUx3 Configuration) for screw location. Figure 5-31 Attach Stand Mount Brackets to Chassis with...
  • Page 213: Figure 5-32 Chs1U-Au+Chs2U-Aux2 Chassis Configuration

    Figure 5-33 CHS1U-AU+CHS2U-AUx3 Chassis Configuration on page 5-30. To prevent damage to the 1U/2U chassis due to falling, NEC recommends screws be installed in the floor mount brackets as soon as possible. Figure 5-32 CHS1U-AU+CHS2U-AUx2 Chassis Configuration System Hardware Manual...
  • Page 214: Rack Mounting The 19" Chassis

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Figure 5-33 CHS1U-AU+CHS2U-AUx3 Chassis Configuration Connect the ground wire to all chassis. Refer to 3.5.7 Install 19” Chassis Grounding on page 5-45 for complete details on grounding the system. Refer to 3.5 Installing the 19” Chassis on page 5-33 to continue installation of the chassis or, Chapter 5 paragraph 2.3 Installing...
  • Page 215: Figure 5-34 19" Rack Mount Brackets

    UNIVERGE SV8100/SV8300 Issue No. 1.5 CHS1U-AU Rack CHS2U-AU Rack Mount Bracket Mount Bracket Figure 5-34 19” Rack Mount Brackets Line up the Rack Mount Bracket(s) with the pre-drilled holes on each side of the 19” chassis. Secure the brackets to the chassis using the supplied screws. Refer to Figure 5-35 Rack Mount Bracket Installed 19”...
  • Page 216: Figure 5-36 Rack Mount Bracket Installed 19" Chs2U-Au Chassis

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Figure 5-36 Rack Mount Bracket Installed 19” CHS2U-AU Chassis Carefully slide the chassis into desired location within the rack. Make sure the hooks on the mounting bracket are inserted into the back of the chassis, securing it in place. Note that the cabling is run through the front of the rack for ease of access.
  • Page 217: Installing The 19" Chassis

    Inspect the equipment for any physical damage. If you are not sure about the function of a component, review the associated information within this manual. Contact your authorized NEC Sales Representative if you have additional questions. Note that the chassis does not initially contain any blades.
  • Page 218: Installing The 19" Controlling Chassis

    Issue No. 1.5 UNIVERGE SV8100/SV8300 3.5.3 Installing the 19” Controlling Chassis Do not remove or install this blade with the power on. Ensure the chassis is powered down. Align the CC-CP00 blade with the slot guide of the Controlling Chassis.
  • Page 219: Installing The 19" Expansion Chassis

    UNIVERGE SV8100/SV8300 Issue No. 1.5 3.5.4 Installing the 19” Expansion Chassis Do not remove or install this blade with the power on. Ensure the chassis is powered down. Align the blade with the universal slots of the Expansion Chassis. Figure 5-39 19” CHS2U-AU Expansion Chassis Slide the blade into the chassis until resistance (back plane) is felt.
  • Page 220: Table 5-2 Pz-Bs10/Pz-Bs11 Connector Pin-Out

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Use only the CAT 5 cables provided by NEC to make the connections between the Controlling and Expansion Chassis. The PZ-BS10 provides: Communication Processor Interface for data handling through Communication Channel (18 slots maximum) 64 Channels for Telephony Resource (e.g., DTMF Tone Receiver,...
  • Page 221: Figure 5-40 Pz-Bs10 Expansion Bay In Controlling Chassis

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Ensure the chassis is powered down. Do not remove or install this blade with the power on. Locate the door positioned on the left end (expansion bay) of the Controlling Chassis (refer to Figure 5-40 PZ-BS10 Expansion Bay in Controlling Chassis).
  • Page 222: Figure 5-42 Pz-Bs10 Blade Guides

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Align the PZ-BS10 blade with the guides located within the expansion bay (refer to Figure 5-42 PZ-BS10 Blade Guides). Guides Figure 5-42 PZ-BS10 Blade Guides Figure 5-43 PZ-BS10 Components Slide the PZ-BS10 blade into the chassis until resistance (back plane) is felt.
  • Page 223: Figure 5-45 Pz-Bs10 Blade Installed

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Align the door with the hinge and reattach the door. Screw Hinge Figure 5-45 PZ-BS10 Blade Installed Close the PZ-BS10 cover. Figure 5-46 PZ-BS10 Installed (Cover Closed) 3.5.5.3 Install the PZ-BS11 Expansion Blade in the CHS2U-AU...
  • Page 224: Figure 5-48 Open Expansion Chassis Cover

    Issue No. 1.5 UNIVERGE SV8100/SV8300 From the left side of the chassis, pull cover outward to expose the expansion bay. Figure 5-48 Open Expansion Chassis Cover Pull the cover toward you to remove. Cover must be removed to install PZ-BS11 blade.
  • Page 225: Figure 5-50 Installing Pz-Bs11 Blade In Expansion Chassis

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Slide the PZ-BS11 blade into the chassis until resistance (back plane) is felt. Figure 5-50 Installing PZ-BS11 Blade in Expansion Chassis Gently push until the blade seats and install the supplied retaining screw. Align the door tabs with hinges and reattach the cover.
  • Page 226: Figure 5-52 Pz-Bs11 Installed (Cover Closed)

    Issue No. 1.5 UNIVERGE SV8100/SV8300 Close the PZ-BS11 blade cover. Figure 5-52 PZ-BS11 Installed (Cover Closed) 3.5.5.4 Connect the Controlling and Expansion Chassis Installment of the PZ-BS10 blade and PZ-BS11 blade(s) must be completed prior to installation of the provided...
  • Page 227: Figure 5-54 System Expansion Cabling

    UNIVERGE SV8100/SV8300 Issue No. 1.5 Ensure Controlling and Expansion chassis are powered down. Using the NEC provided CAT5 straight-through cable(s), attach one end to each Expansion Chassis BUS connector on the PZ-BS11 blade (see Figure 5-54 System Expansion Cabling. Attach the opposite end to the BUS connector on the PZ-BS10 of the Controlling Chassis.
  • Page 228: Cable Connection Between Cpu Blades

    Issue No. 1.5 UNIVERGE SV8100/SV8300 3.5.6 Cable Connection between CPU Blades When providing multiple-unit configuration, the IP connection between UNITs is required. The UNIT is connected to IP network via the VoIPDB blade on the CPU blade. Refer to Figure 5-55 Cable Connection between CPU Blades.