Huawei Quidway S9300 Configuration Manual page 60

2 Link Aggregation Configuration
<Quidway> system-view
[Quidway] sysname S9300-B
[S9300-B] interface eth-trunk 1
[S9300-B-Eth-Trunk1] mode lacp-static
[S9300-B-Eth-Trunk1] quit
Step 2 Add member interfaces to the Eth-Trunk.
# Configure S9300-A.
[S9300-A] interface gigabitethernet 1/0/1
[S9300-A-Gigabitethernet1/0/1] eth-trunk 1
[S9300-A-Gigabitethernet1/0/1] quit
[S9300-A] interface gigabitethernet 1/0/2
[S9300-A-Gigabitethernet1/0/2] eth-trunk 1
[S9300-A-Gigabitethernet1/0/2] quit
[S9300-A] interface gigabitethernet 1/0/3
[S9300-A-Gigabitethernet1/0/3] eth-trunk 1
[S9300-A-Gigabitethernet1/0/3] quit
# Configure S9300-B.
[S9300-B] interface gigabitethernet 1/0/1
[S9300-B-Gigabitethernet1/0/1] eth-trunk 1
[S9300-B-Gigabitethernet1/0/1] quit
[S9300-B] interface gigabitethernet 1/0/2
[S9300-B-Gigabitethernet1/0/2] eth-trunk 1
[S9300-B-Gigabitethernet1/0/2] quit
[S9300-B] interface gigabitethernet 1/0/3
[S9300-B-Gigabitethernet1/0/3] eth-trunk 1
[S9300-B-Gigabitethernet1/0/3] quit
Step 3 Set the system priority on S9300-A to 100 so that S9300-A becomes the Actor.
[S9300-A] lacp priority 100
Step 4 Set the upper threshold M of active interfaces on S9300-A to 2.
[S9300-A] interface eth-trunk 1
[S9300-A-Eth-Trunk1] max bandwidth-affected-linknumber 2
[S9300-A-Eth-Trunk1] quit
Step 5 Set the priority of the interface and determine active links on S9300-A.
[S9300-A] interface gigabitethernet 1/0/1
[S9300-A-Gigabitethernet1/0/1] lacp priority 100
[S9300-A-Gigabitethernet1/0/1] quit
[S9300-A] interface gigabitethernet 1/0/2
[S9300-A-Gigabitethernet1/0/2] lacp priority 100
[S9300-A-Gigabitethernet1/0/2] quit
Step 6 Verify the configuration.
# Check information about the Eth-Trunk of the S9300s and check whether the negotiation is
successful on the link.
[S9300-A] display eth-trunk 1
Eth-Trunk1's state information is:
Local:
LAG ID: 1
Preempt Delay: Disabled
System Priority: 100
Least Active-linknumber: 1
Operate status: Up
------------------------------------------------------------------------------
ActorPortName
Weight
GigabitEthernet1/0/1
1
GigabitEthernet1/0/2
2-24
WorkingMode: STATIC
Hash arithmetic: According to SA-XOR-DA
System ID: 00e0-fca8-0417
Max Active-linknumber: 2
Number Of Up Port In Trunk: 2
Status PortType
Selected 1GE
Selected 1GE
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
Quidway S9300 Terabit Routing Switch
Configuration Guide - Ethernet
PortPri PortNo PortKey
100 6145 2865
100 6146 2865
PortState
11111100
11111100
Issue 03 (2009-08-20)