Huawei Quidway S9300 Configuration Manual page 283

Quidway S9300 Terabit Routing Switch
Configuration Guide - Ethernet
# Configure PE1.
[PE1] vlan 10
[PE1-Vlan10] quit
[PE1] interface gigabitethernet 1/0/0
[PE1-GigabitEthernet1/0/0] port link-type trunk
[PE1-GigabitEthernet1/0/0] port trunk allow-pass vlan 10
[PE1-GigabitEthernet1/0/0] bpdu enable
[PE1-GigabitEthernet1/0/0] quit
[PE1] interface gigabitethernet 1/0/1
[PE1-GigabitEthernet1/0/1] port hybrid untagged vlan 10
[PE1-GigabitEthernet1/0/1] port vlan-stacking outside-vlan 100 stack-vlan 10
[PE1-GigabitEthernet1/0/1] stp disable
[PE1-GigabitEthernet1/0/1] bpdu enable
[PE1-GigabitEthernet1/0/1] quit
[PE1] interface gigabitethernet 1/0/2
[PE1-GigabitEthernet1/0/2] port hybrid untagged vlan 10
[PE1-GigabitEthernet1/0/2] port vlan-stacking outside-vlan 200 stack-vlan 10
[PE1-GigabitEthernet1/0/2] stp disable
[PE1-GigabitEthernet1/0/2] bpdu enable
[PE1-GigabitEthernet1/0/2] quit
# Configure PE2.
[PE2] vlan 10
[PE2-Vlan10] quit
[PE2] interface gigabitethernet 1/0/0
[PE2-GigabitEthernet1/0/0] port link-type trunk
[PE2-GigabitEthernet1/0/0] port trunk allow-pass vlan 10
[PE2-GigabitEthernet1/0/0] bpdu enable
[PE2-GigabitEthernet1/0/0] quit
[PE2] interface gigabitethernet 1/0/1
[PE2-GigabitEthernet1/0/1] port hybrid untagged vlan 10
[PE2-GigabitEthernet1/0/1] port vlan-stacking outside-vlan 100 stack-vlan 10
[PE2-GigabitEthernet1/0/1] stp disable
[PE2-GigabitEthernet1/0/1] bpdu enable
[PE2-GigabitEthernet1/0/1] quit
[PE2] interface gigabitethernet 1/0/2
[PE2-GigabitEthernet1/0/2] port hybrid untagged vlan 10
[PE2-GigabitEthernet1/0/2] port vlan-stacking outside-vlan 200 stack-vlan 10
[PE2-GigabitEthernet1/0/2] stp disable
[PE2-GigabitEthernet1/0/2] bpdu enable
[PE2-GigabitEthernet1/0/2] quit
Step 5 Verify the configuration.
Run the display stp command on CE1 and CE2 to view the roots in the MST region. You can
find that a spanning tree is calculated between CE1 and CE2. GE 1/0/0 of CE1 is a root port,
and CE 1/0/0 of CE2 is a designated port.
<CE1> display stp
-------[CIST Global Info][Mode MSTP]-------
CIST Bridge
Bridge Times
CIST Root/ERPC
CIST RegRoot/IRPC
CIST RootPortId
BPDU-Protection
TC or TCN received
STP Converge Mode
Time since last TC received :0 days 3h:53m:43s
----[Port17(GigabitEthernet1/0/0)][FORWARDING]----
Port Protocol
Port Role
Port Priority
Port Cost(Dot1T )
Desg. Bridge/Port
Port Edged
Issue 03 (2009-08-20)
:32768.000b-09f0-1b91
:Hello 2s MaxAge 20s FwDly 15s MaxHop 20
:32768.000b-09d4-b66c / 199999
:32768.000b-09f0-1b91 / 0
:128.82
:disabled
:2
:Fast
:enabled
:CIST Root Port
:128
:Config=auto / Active=199999
:32768.000b-09d4-b66c / 128.82
:Config=disabled / Active=disabled
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
9 BPDU Tunnel Configuration
9-47