Huawei Quidway S9300 Configuration Manual page 276

9 BPDU Tunnel Configuration
[PE1] vlan 200
[PE1-vlan200] quit
[PE1] interface gigabitethernet 1/0/0
[PE1-GigabitEthernet1/0/0] port link-type trunk
[PE1-GigabitEthernet1/0/0] port trunk allow-pass vlan 100 200
[PE1-GigabitEthernet1/0/0] quit
[PE1] interface gigabitethernet 1/0/1
[PE1-GigabitEthernet1/0/1] port link-type trunk
[PE1-GigabitEthernet1/0/1] port trunk allow-pass vlan 100
[PE1-GigabitEthernet1/0/1] stp disable
[PE1-GigabitEthernet1/0/1] bpdu-tunnel stp vlan 100
[PE1-GigabitEthernet1/0/1] quit
[PE1] interface gigabitethernet 1/0/2
[PE1-GigabitEthernet1/0/2] port link-type trunk
[PE1-GigabitEthernet1/0/2] port trunk allow-pass vlan 200
[PE1-GigabitEthernet1/0/2] stp disable
[PE1-GigabitEthernet1/0/2] bpdu-tunnel stp vlan 200
[PE1-GigabitEthernet1/0/2] quit
# Configure PE2.
[PE2] vlan 100
[PE2-vlan100] quit
[PE2] vlan 200
[PE2-vlan200] quit
[PE2] interface gigabitethernet 1/0/0
[PE2-GigabitEthernet1/0/0] port link-type trunk
[PE2-GigabitEthernet1/0/0] port trunk allow-pass vlan 100 200
[PE2-GigabitEthernet1/0/0] quit
[PE2] interface gigabitethernet 1/0/1
[PE2-GigabitEthernet1/0/1] port link-type trunk
[PE2-GigabitEthernet1/0/1] port trunk allow-pass vlan 100
[PE2-GigabitEthernet1/0/1] stp disable
[PE2-GigabitEthernet1/0/1] bpdu-tunnel stp vlan 100
[PE2-GigabitEthernet1/0/1] quit
[PE2] interface gigabitethernet 1/0/2
[PE2-GigabitEthernet1/0/2] port link-type trunk
[PE2-GigabitEthernet1/0/2] port trunk allow-pass vlan 200
[PE2-GigabitEthernet1/0/2] stp disable
[PE2-GigabitEthernet1/0/2] bpdu-tunnel stp vlan 200
[PE2-GigabitEthernet1/0/2] quit
Step 5 Configure the basic Layer 2 forwarding function and allow packets with VLAN tags 100 and
200 to pass through.
[P] vlan 100
[P-vlan100] quit
[P] vlan 200
[P-vlan200] quit
[P] interface gigabitethernet 1/0/0
[P-GigabitEthernet1/0/0] port link-type trunk
[P-GigabitEthernet1/0/0] port trunk allow-pass vlan 100 200
[P-GigabitEthernet1/0/0] quit
[P] interface gigabitethernet 1/0/1
[P-GigabitEthernet1/0/1] port link-type trunk
[P-GigabitEthernet1/0/1] port trunk allow-pass vlan 100 200
[P-GigabitEthernet1/0/1] quit
Step 6 Verify the configuration.
Run the display stp command on CE1 and CE2 to view the roots in the MST region. You can
find that a spanning tree is calculated between CE1 and CE2. GE 1/0/0 of CE1 is a root port,
and CE 1/0/0 of CE2 is a designated port.
<CE1> display stp
-------[CIST Global Info][Mode MSTP]-------
CIST Bridge
Bridge Times
CIST Root/ERPC
9-40
:32768.000b-09f0-1b91
:Hello 2s MaxAge 20s FwDly 15s MaxHop 20
:32768.000b-09d4-b66c / 199999
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
Quidway S9300 Terabit Routing Switch
Configuration Guide - Ethernet
Issue 03 (2009-08-20)