Huawei Quidway S9300 Configuration Manual page 264

9 BPDU Tunnel Configuration
[PE1] vlan 100
[PE1-vlan100] quit
[PE1] interface GigabitEthernet 1/0/0
[PE1-GigabitEthernet1/0/0] port hybrid pvid vlan 100
[PE1-GigabitEthernet1/0/0] port hybrid untagged vlan 100
[PE1-GigabitEthernet1/0/0] stp disable
[PE1-GigabitEthernet1/0/0] bpdu enable
[PE1-GigabitEthernet1/0/0] quit
[PE1] vlan 200
[PE1-vlan200] quit
[PE1] interface GigabitEthernet 1/0/1
[PE1-GigabitEthernet1/0/1] port hybrid pvid vlan 200
[PE1-GigabitEthernet1/0/1] port hybrid untagged vlan 200
[PE1-GigabitEthernet1/0/1] stp disable
[PE1-GigabitEthernet1/0/1] bpdu enable
[PE1-GigabitEthernet1/0/1] quit
# Configure PE2.
[PE2] vlan 100
[PE2-vlan100] quit
[PE2] interface GigabitEthernet 1/0/0
[PE2-GigabitEthernet1/0/0] port hybrid pvid vlan 100
[PE2-GigabitEthernet1/0/0] port hybrid untagged vlan 100
[PE2-GigabitEthernet1/0/0] stp disable
[PE2-GigabitEthernet1/0/0] bpdu enable
[PE2-GigabitEthernet1/0/0] quit
[PE2] vlan 200
[PE2-vlan200] quit
[PE2] interface GigabitEthernet 1/0/1
[PE2-GigabitEthernet1/0/1] port hybrid pvid vlan 200
[PE2-GigabitEthernet1/0/1] port hybrid untagged vlan 200
[PE2-GigabitEthernet1/0/1] stp disable
[PE2-GigabitEthernet1/0/1] bpdu enable
[PE2-GigabitEthernet1/0/1] quit
Step 4 On the PE devices, configure GE 1/0/2 at the PSN side to allow BPDUs from VLAN 100 and
VLAN 200 to pass through.
# Configure PE1.
[PE1] interface gigabitethernet 1/0/2
[PE1-GigabitEthernet1/0/2] port link-type trunk
[PE1-GigabitEthernet1/0/2] port trunk allow-pass vlan 100 200
[PE1-GigabitEthernet1/0/2] bpdu enable
[PE1-GigabitEthernet1/0/2] quit
# Configure PE2.
[PE2] interface gigabitethernet 1/0/2
[PE2-GigabitEthernet1/0/2] port link-type trunk
[PE2-GigabitEthernet1/0/2] port trunk allow-pass vlan 100 200
[PE2-GigabitEthernet1/0/2] bpdu enable
[PE2-GigabitEthernet1/0/2] quit
Step 5 Verify the configuration.
Run the display stp command on CE1 and CE2 to view the roots in the MST region. You can
find that a spanning tree is calculated between CE1 and CE2. GE 1/0/0 of CE1 is a root port and
GE 1/0/0 of CE2 is a designated port.
<CE1> display stp
-------[CIST Global Info] [Mode MSTP] -------
CIST Bridge
Bridge Times
CIST Root/ERPC
CIST RegRoot/IRPC
CIST RootPortId
BPDU-Protection
9-28
:32768.00e0-fc9f-3257
:Hello 2s MaxAge 20s FwDly 15s MaxHop 20
:32768.00e0-fc9a-4315 / 199999
:32768.00e0-fc9f-3257 / 0
:128.82
:disabled
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
Quidway S9300 Terabit Routing Switch
Configuration Guide - Ethernet
Issue 03 (2009-08-20)