Table Of Contents - Fagor CNC 8060 Installation Manual

I n s t a l l a t i o n m a n u a l .
About the product - CNC 8060 ....................................................................................................11
About the product - CNC 8065 ................................................................................................... 15
Declaration of CE conformity and warranty conditions ............................................................... 19
Version history - CNC 8060 ........................................................................................................ 21
Version history - CNC 8065 ........................................................................................................ 27
Safety conditions ........................................................................................................................ 33
Returning conditions ................................................................................................................... 37
CNC maintenance ...................................................................................................................... 39
[1] INSTALLATION MANUAL.
CHAPTER 1 SOFTWARE INSTALLATION.
1.1 Software installation at the CNC. ................................................................................... 43
1.1.1 Work modes and software protection at the CNC...................................................... 45
1.2 Software installation at the PC (simulator)..................................................................... 48
1.3 Updating the software version. ...................................................................................... 50
1.3.1 Software update and incompatibilities (8060). ........................................................... 51
1.3.2 Software update and incompatibilities (8065). ........................................................... 52
1.4 Requirements before and after CNC setup.................................................................... 53
1.5 Installation of third-party software (CNC 8065 only). ..................................................... 54
1.6 Software configuration. .................................................................................................. 55
1.6.1 MTB (Machine Tool Builder) folder. ........................................................................... 56
1.6.2 USERS folder............................................................................................................. 57
CHAPTER 2 MACHINE PARAMETERS.
2.1 Parameter matching between the CNC and the Sercos drive. ...................................... 61
2.2 Parameters to verify before the startup.......................................................................... 63
2.3 General machine parameters. ....................................................................................... 65
2.3.1 Channel configuration. ............................................................................................... 65
2.3.2 Configuring the axes of the system............................................................................ 66
2.3.3 Configuration of a tandem system. ............................................................................ 67
2.3.4 Configuration of a gantry axis. ................................................................................... 71
2.3.5 Configuration of a multi-axis group. ........................................................................... 74
2.3.6 Configuring the spindles of the system. ..................................................................... 76
2.3.7 Time setting (system)................................................................................................. 77
2.3.8 Sercos bus configuration............................................................................................ 79
2.3.9 Mechatrolink bus configuration. ................................................................................. 80
2.3.10 CAN bus configuration. .............................................................................................. 81
2.3.11 Serial line configuration.............................................................................................. 82
2.3.12 MODBUS. .................................................................................................................. 83
2.3.13 Default conditions (sytem).......................................................................................... 84
2.3.14 Arithmetic parameters. ............................................................................................... 85
2.3.15 Cross compensation table.......................................................................................... 87
2.3.16 Volumetric compensation tables. ............................................................................... 90
2.3.17 Execution times.......................................................................................................... 93
2.3.18 Numbering of the digital inputs (CANfagor bus)......................................................... 94
2.3.19 Numbering of the digital outputs (CANfagor bus). ..................................................... 95
2.3.20 Numbering of the digital inputs (CANopen bus)......................................................... 96
2.3.21 Numbering of the digital outputs (CANopen bus)....................................................... 98
2.3.22 Numbering of analog inputs for temperature sensors PT100. ................................. 100
2.3.23 Probe setting. ........................................................................................................... 101
2.3.24 Shared PLC memory................................................................................................ 103
2.3.25 Management of local I/O. ......................................................................................... 103
2.3.26 Synchronized switching............................................................................................ 104
2.3.27 PWM (Pulse-Width Modulation). .............................................................................. 105
2.3.28 Power control. .......................................................................................................... 106
2.3.29 Gap control............................................................................................................... 107
2.3.30 Leapfrog. .................................................................................................................. 112
2.3.31 Compensating the dispersion by the CO2 laser path............................................... 113
2.3.32 Backup of non-volatile data...................................................................................... 115
2.3.33 Tool offset and wear................................................................................................. 115
2.3.34 Spindle synchronization. .......................................................................................... 116
I N D E X
CNC 8060
CNC 8065
(R : 1709)
EF
·3·