Plc --> Manager Communication - Fagor CNC 8060 Installation Manual

7.3.2
7.
CNC 8060
CNC 8065
(R : 1709)
EF
·456·
PLC --> Manager communication.
The PLC uses the following marks to inform the manager about the operations that it has
carried out. There is one group of marks for each magazine.
The PLC, depending on the type of magazine, must take some actions to execute the
operations requested by the manager. After ending each one of them, it must activate certain
marks to inform the manager that the action has been completed. The manager sets them
back to "0" once they are read.
The following table shows the mnemonics for each mark (M) or register (R) in each channel
or magazine.
Magazine ·1·
M MZTOCH1
MZTOCH1MZ1
M CH1TOSPDL
CH1TOSPDLMZ1
M SPDLTOCH1
SPDLTOCH1MZ1
M SPDLTOCH2
SPDLTOCH2MZ1
M CH1TOMZ
CH1TOMZ1
M CH2TOMZ
CH2TOMZ1
M SPDLTOGR
SPDLTOGRC1
M GRTOSPDL
GRTOSPDLC1
M MZTOSPDL
MZTOSPDLMZ1
M SPDLTOMZ
SPDLTOMZ1
M MZROT
MZROTMZ1
M TCHANGEOK
TCHANGEOKMZ1
R MZPOS
MZPOSMZ1
The meaning of the marks and registers is as follows.
Marks / Registers.
MZTOCH1
CH1TOSPDL
SPDLTOCH1
SPDLTOCH2
CH1TOMZ
Magazine ·2· Magazine ·3·
MZTOCH1MZ2 MZTOCH1MZ3
CH1TOSPDLMZ2 CH1TOSPDLMZ3
SPDLTOCH1MZ2 SPDLTOCH1MZ3
SPDLTOCH2MZ2 SPDLTOCH2MZ3
CH1TOMZ2 CH1TOMZ3
CH2TOMZ2 CH2TOMZ3
SPDLTOGRC2 SPDLTOGRC3
GRTOSPDLC2 GRTOSPDLC3
MZTOSPDLMZ2 MZTOSPDLMZ3
SPDLTOMZ2 SPDLTOMZ3
MZROTMZ2 MZROTMZ3
TCHANGEOKMZ2 TCHANGEOKMZ3
MZPOSMZ2 MZPOSMZ3
Meaning,
Use it with an asynchronous magazine or synchronous with arm.
The PLC must set this mark high (=1) after taking the tool from the
magazine to the changer arm 1.
Use it with an asynchronous magazine or synchronous with arm.
The PLC must set this mark high (=1) after taking the tool from the
changer arm 1 to the spindle.
Use it with an asynchronous magazine with one changer arm. The
PLC must set this mark high (=1) after taking the tool from the spindle
to the changer arm 1.
Use it with an asynchronous magazine or synchronous with arm.
The PLC must set this mark high (=1) after taking the tool from the
spindle to the changer arm 2.
Use it with an asynchronous magazine or synchronous with
arm. The PLC must set this mark high (=1) after taking the tool
from the tool changer arm 1 to the magazine.
I n s ta ll a t io n ma n u a l.
Magazine ·4·
MZTOCH1MZ4
CH1TOSPDLMZ4
SPDLTOCH1MZ4
SPDLTOCH2MZ4
CH1TOMZ4
CH2TOMZ4
SPDLTOGRC4
GRTOSPDLC4
MZTOSPDLMZ4
SPDLTOMZ4
MZROTMZ4
TCHANGEOKMZ4
MZPOSMZ4