Mitsubishi Electric FR-A820-00046 Instruction Manual page 513

Parameters
Since the voltage and current display on the operation panel (FR-DU08) is shown in four digits, a
monitor value of more than "9999" is displayed as "
The setting is available only for standard models.
When the output current is less than the specified current level (5% of the rated inverter current),
the output current is monitored as 0 A. Therefore, the monitored value of an output current and
output power may be displayed as "0" when using a much smaller-capacity motor compared to
the inverter or in other instances that cause the output current to fall below the specified value.
Can be changed to the pulse display after the electronic gear using Pr. 430 "Pulse monitor
selection" (refer to page 5-172).
Available when the plug-in option or control terminal option is connected.
Input terminal monitor details ("1" denotes terminal ON, "0" denotes terminal OFF, and "
undetermined value.)
b15
⎯
Output terminal monitor details ("1" denotes terminal ON, "0" denotes terminal OFF, and "
denotes undetermined value.)
b15
⎯
Option input terminal monitor 1 details (FR-A8AX input terminal status, "1" denotes terminal ON
and "0" denotes terminal OFF.)
All are OFF when the option is not connected.
b15
X15
Option input terminal monitor 2 details (FR-A8AX input terminal status. "1" denotes terminal ON,
"0" denotes terminal OFF, "
All are OFF when the option is not connected.
b15
⎯
Option output terminal monitor details (FR-A8AY/A8AR output terminal status. "1" denotes termi-
nal ON, "1" denotes terminal OFF, and "
All are OFF when the option is not connected.
b15
⎯
The increment is 1 when Pr. 37 = "1 to 9998" or when Pr. 144 = "2 to 12" or "102 to 112". (Refer to
page 5-324.)
The monitored values are retained even if an inverter fault occurs. Resetting will clear the retained
values.
Parameter setting is not available for setting the item as the main monitor data on the LCD
operation panel (FR-LU08) or the parameter unit (FRPU07). Use the monitor function of the FR-
LU08 or the FR-PU07 for setting.
Negative values are not displayed on the operation panel. The values "-1 to -32767" are displayed
as "65535 to 32769" on the operation panel.
Setting of Pr. 1018 "Monitor with sign selection" is required. Besides, displayed without minus sign
on the operation panel. Confirm the rotation direction with the [FWD] or [REV] indicator.
FR-A800
⎯ ⎯ ⎯
CS RES
⎯ ⎯ ⎯ ⎯
X14 X13 X12 X11 X10
⎯
" denotes undetermined value.)
⎯ ⎯ ⎯ ⎯
⎯ ⎯ ⎯ ⎯
(M) Monitor display and monitor output signal
⎯
".
STP
MRS JOG RH
(STOP)
⎯ ⎯ ⎯
SO ABC2 ABC1
X9 X8 X7 X6
⎯ ⎯ ⎯ ⎯ ⎯
⎯
" denotes undetermined value.)
⎯
RA3 RA2 RA1 Y6
⎯
RM RL RT AU STR
FU OL IPF SU
X5 X4 X3 X2 X1
⎯ ⎯ ⎯ ⎯ ⎯
Y5 Y4 Y3 Y2 Y1
" denotes
b0
STF
⎯
"
b0
RUN
b0
X0
b0
DY
b0
Y0
5 - 333