Mitsubishi Electric FR-A820-00046 Instruction Manual page 227

Parameters
(N) Operation via communication and its settings
Parameters for communication operation. These param-
eters set the communication specifications and opera-
tion.
Pr.
Pr. Name
group
N000 549 Protocol selection
Communication EEPROM write
N001 342
selection
MODBUS RTU communication check
N002 539
time interval
Stop mode selection at
N013 502
communication error
Operation frequency during
N014 779
communication error
N020 117 PU communication station number
N021 118 PU communication speed
N022 119 PU communication data length
N023 119 PU communication stop bit length
N024 120 PU communication parity check
Number of PU communication
N025 121
retries
PU communication check time
N026 122
interval
PU communication waiting time
N027 123
setting
N028 124 PU communication CR/LF selection
RS-485 communication station
N030 331
number
N031 332 RS-485 communication speed
N032 333 PU communication data length
N033 333 PU communication stop bit length
RS-485 communication parity check
N034 334
selection
N035 335 RS-485 communication retry count
RS-485 communication check time
N036 336
interval
RS-485 communication waiting time
N037 337
setting
RS-485 communication CR/LF
N038 341
selection
N040 547 USB communication station number
USB communication check time
N041 548
interval
N080 343 Communication error count
N500 1300
to to
Communication option parameters.
N543, 1343,
For details, refer to the Instruction Manual of
N550 1350
the option.
to to
N559 1359
Tab. 5-15: Operation via communication and its
settings
FR-A800
(G) Control Parameter
Parameters for motor control.
Pr.
Pr.
group
Refer to
G000 0
page
G001 3
5-606
G002 19
5-606
G003 14
G010 46
5-630
G011 47
5-606
G020 112
G021 113
5-606
G030 60
5-610
G040 100
5-610
G041 101
5-610
G042 102
5-610
G043 103
5-610
G044 104
5-610
G045 105
G046 106
5-610
G047 107
G048 108
5-610
G049 109
5-610
G060 673
5-610
G061 674
5-610
G100 10
5-610
5-610
G101 11
G102 802
5-610
G103 850
5-610
G105 522
5-610
G106 250
G107
70
5-610
G108 1299
5-610
G110 12
5-648
G120 882
5-648
G121 883
5-630
G122 884
G123 885
G124 886
G125 665
G130 660
G131 661
Tab. 5-16:
Name
Simple Simple Simple
Torque boost
Simple Simple Simple
Base frequency
Base frequency voltage
Load pattern selection
Second torque boost
Second V/F (base frequency)
Third torque boost
Third V/F (base frequency)
Energy saving control selection
V/F1(first frequency)
V/F1(first frequency voltage)
V/F2 (second frequency)
V/F2 (second frequency voltage)
V/F3 (third frequency)
V/F3 (third frequency voltage)
V/F4 (fourth frequency)
V/F4 (fourth frequency voltage)
V/F5 (fifth frequency)
V/F5 (fifth frequency voltage)
SF-PR slip amount adjustment
operation selection
SF-PR slip amount adjustment gain
DC injection brake operation
frequency
DC injection brake operation time
Pre-excitation selection
Brake operation selection
Output stop frequency
Stop selection
Special regenerative brake duty
Second pre-excitation selection
DC injection brake operation
voltage
Regeneration avoidance operation
selection
Regeneration avoidance operation
level
Regeneration avoidance at
deceleration detection sensitivity
Regeneration avoidance
compensation frequency limit value
Regeneration avoidance voltage
gain
Regeneration avoidance frequency
gain
Increased magnetic excitation
deceleration operation selection
Magnetic excitation increase rate
Control Parameter (1)
Parameter List
Refer to
page
5-652
5-654
5-654
5-656
5-652
5-654
5-652
5-654
5-659
5-660
5-660
5-660
5-660
5-660
5-660
5-660
5-660
5-660
5-660
5-662
5-662
5-663
5-663
5-663
5-663
5-671
5-430
5-675
5-663
5-663
5-685
5-685
5-685
5-685
5-685
5-685
5-689
5-689
5 - 47