HEIDENHAIN TNC 620 User Manual page 518

Index
3
3-D basic rotation......................... 226
3-D touch probe
Calibrating................................. 215
using........................................... 204
A
About this manual.......................... 26
ACC................................................. 312
Accessories................................... 124
Active Chatter Control................. 312
Adding a network drive................ 423
ADP.................................................. 296
Automatic program start............ 298
Automatic tool measurement.... 137
Axis display...................................... 68
Axis position, checking................ 167
B
Backup............................................ 400
Basic rotation................................ 223
measuring in Manual operation
mode.......................................... 223
Batch Process Manager.............. 330
application................................ 330
creating a job list..................... 336
editing a job list........................ 337
fundamentals........................... 330
job list........................................ 331
opening...................................... 334
Behavior after receipt of ETX..... 408
Block check character................. 407
Block scan..................................... 283
after a power failure................ 283
in a pallet table......................... 288
in a point table......................... 288
tool oriented............................. 329
Browser............................................. 96
Bus Diagnosis............................... 366
C
Calling tool management............ 151
CAM programming....................... 291
Checking the axis positions........ 190
Code number entry...................... 343
Compensating workpiece
misalignment
By measuring two points on a
straight surface........................ 221
Condition of RTS line................... 407
Configuration data....................... 490
Connecting cable.......................... 507
Context-sensitive help................. 107
Counter........................................... 314
Setting........................................ 350
518
D
Data Backup........................... 92, 400
Data interface................................ 405
pin layout................................... 507
setting up.................................. 405
Data transfer
File system............................... 407
software.................................... 408
Data transmission
Behavior after receipt of ETX 408
Block check character............ 407
Condition of RTS line.............. 407
Data bits.................................... 406
Handshake................................ 407
Parity.......................................... 406
Protocol..................................... 406
Stop bits.................................... 406
TNCserver software................ 408
Datum table
Program run............................. 276
transferring probed values..... 213
Diagnostics.................................... 366
Directory........................................... 82
Displaying an HTML file................. 96
Displaying an Internet file.............. 96
Display screen................................. 59
DNC................................................. 403
Downloading help files................ 111
DriveDiag........................................ 366
E
EnDat encoder.............................. 167
Error message............................... 101
deleting...................................... 104
filtering....................................... 103
help with.................................... 101
Ethernet interface................ 412, 507
Configuration................... 417, 421
connection possibility............. 412
introduction............................... 412
Setting........................................ 413
Exporting the workpiece.............. 263
Extended collision monitoring.... 255
External access............................. 354
External data transfer.................... 90
F
FCL function.................................... 33
Feature Content Level.................... 33
Feed rate........................................ 183
changing.................................... 184
limiting....................................... 185
File
importing..................................... 92
protecting.................................... 84
File management............................ 80
external data transfer................ 90
HEIDENHAIN | TNC 620 | User's Manual for Setup, Testing and Running NC Programs | 01/2022
External file types...................... 82
File manager
Calling.......................................... 83
Directory...................................... 82
File type....................................... 80
Hidden files................................. 85
Selecting files............................. 86
File status......................................... 83
Firewall........................................... 402
Functional safety FS.................... 186
FUNCTION COUNT....................... 314
Fundamentals............................... 113
G
Gestures......................................... 476
GOTO............................................... 268
Graphics......................................... 246
view options............................. 248
Graphic settings............................ 348
Graphic simulation....................... 253
tool.............................................. 250
H
Handwheel..................................... 173
Hard disk.......................................... 80
Hardware configuration.............. 366
HEIDENHAIN OPC UA NC
Server.............................................. 462
Help system................................... 107
Help with error message............. 101
HeROS
information............................... 366
Hidden files...................................... 85
I
Import
file from iTNC 530..................... 92
table from iTNC 530............... 139
Indiziertes Werkzeug................... 131
Interface
Configuring............................... 415
Interrupt machining...................... 274
iTNC 530.......................................... 56
J
Jumping
with GOTO................................. 268
K
Kinematics..................................... 351
L
Lift-off............................................. 310
Loading the machine configuration..
344
Login
with password.......................... 452
with token................................. 460
Index