Canon iR C3200 Series Service Manual page 771

motor (Bk) not rotating (Refer to SymptomExplanation.) .................................................................... 16-132
16.3.10.22 E020-04B0 Cautions in replacing the drum unit ..................................................................... 16-133
16.3.10.23 E020-0X81 Error Code Displaying because of an open/close failure of the SALT
sensor shutter ......................................................................................................................................... 16-134
16.3.10.24 E020-0124 Error Code ........................................................................................................... 16-134
16.3.10.25 E020-OXB0 Error Code .......................................................................................................... 16-135
16.3.10.26 E020-xx24 Error Code ............................................................................................................ 16-135
16.3.10.27 E020-xxA0 Error Code ............................................................................................................ 16-136
16.3.10.28 E020-xxD0 Error Code ............................................................................................................ 16-136
16.3.10.29 E020-xx34 Error Code ............................................................................................................ 16-136
16.3.10.30 E020-0125 Error Code ............................................................................................................ 16-137
16.3.10.31 E020-03B0 Error Code: Overall fogging (no margin) occurred after replacement of Cyan
drum unit ............................................................................................................................................... 16-137
16.3.10.32 E032 Error code detail The counter of the NE controller fails to operate. ............................ 16-137
16.3.10.33 E110 Error code detail The operation of the laser scanner motor is faulty. ........................... 16-137
16.3.10.34 E110-0x10 Error Code ............................................................................................................ 16-138
16.3.10.35 E202 Error code detail A fault has occurred in detecting the No. 1 mirror home position. .. 16-139
16.3.10.36 E202-0000 Error Code ............................................................................................................ 16-139
16.3.10.37 E220 Error code detail A fault has occurred in activating the scanning lamp. ..................... 16-140
16.3.10.38 E220-0000 Error Code: Entire image sometimes becomes tinged with red ........................... 16-140
16.3.10.39 E220-0000 Error Code ............................................................................................................ 16-141
16.3.10.40 E220-0000 Error code Faulty connection in the flat cable from the CCD unit into
R-CON J205 causes. ............................................................................................................................. 16-141
16.3.10.41 E220-0000 Error Code: Scanning lamp did not light up after turning power ON .................. 16-142
16.3.10.42 E220-0000 Error Code when turning power ON while opening platen cover ........................ 16-142
16.3.10.43 E220-0000 Error Code: No problem with CCD unit and Reader Controller PCB ................. 16-142
16.3.10.44 E220-0000 Error Code: At power-on upon installation, because of poor contact of
J204 on Reader Controller PCB, iRC3220 ............................................................................................ 16-143
16.3.10.45 E240 Error code detail The communication between the main motor controller and
the DC controller is faulty. ................................................................................................................... 16-143
16.3.10.46 E243 Error code detail The control panel is faulty. ................................................................ 16-143
16.3.10.47 E302 Error code detail A fault has occurred in relation to shading correction. .................... 16-144
16.3.10.48 E315 Error code detail The image data is faulty. ................................................................... 16-144
16.3.10.49 E315-0010 Error code Only for FAX is transmitted .............................................................. 16-144
16.3.10.50 E351 Error code detail The ECO-ID PCB is faulty. .............................................................. 16-145
16.3.10.51 E351-0000 Error Code: Because of poor connection of connector on ECO-ID PCB ............. 16-145
16.3.10.52 E402 Error code detail There is a fault in the feeder motor. .................................................. 16-145
16.3.10.53 E402 Error Code ...................................................................................................................... 16-146
16.3.10.54 E404 Error code detail There is a fault in the delivery motor. ............................................... 16-146
16.3.10.55 E500 Error code detail There is a fault in finisher communication. (Finisher-N1) .............. 16-146
16.3.10.56 E500 Error code detail There is a fault in finisher communication. (Finisher-M1) ............... 16-147
16.3.10.57 E503 Error code detail There is a fault in saddle communication. ........................................ 16-147
16.3.10.58 E504 Error code detail There is a fault in stack size detection. ............................................. 16-148
16.3.10.59 E505 Error code detail There is a fault in the backup RAM. ................................................. 16-148
16.3.10.60 E512 Error code detail There is a fault in delivery. (Finisher-N1) ........................................ 16-149
16.3.10.61 E512 Error code detail There is a fault in delivery. (Finisher-M1) ....................................... 16-149
16.3.10.62 E514 Error code detail There is a fault in stack processing (clockwise direction) ................ 16-150
16.3.10.63 E530 Error code detail There is a fault in alignment.(Finisher-N1) ...................................... 16-150
16.3.10.64 E530 Error code detail There is a fault in rear alignment. (Finisher-M1) .............................. 16-151
16.3.10.65 E531 Error code detail There is a fault in stapling. (Finisher-M1) ........................................ 16-151
16.3.10.66 E531 Error code detail There is a fault in stapling. (Finisher-N1) ........................................ 16-152
16.3.10.67 E532 Error code detail There is a fault in the shift of the stapler ........................................... 16-152
16.3.10.68 E535 Error code detail There is a fault in the swing mechanism. ......................................... 16-153
16.3.10.69 E537 Error code detail There is a fault in front alignment. .................................................... 16-153
Contents