Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Canon Image Runner iRC1028i
Summary of Contents for Canon Image Runner iRC1028i
- Page 1 iRC1021i Image Runner MFD Guide for Copying iRC1028i...
-
Page 2: Table Of Contents
MFD User Guide for Copying Contents Key Contacts Introduction Basic Features Original Placement – Platen Glass Original Placement – Document Feeder Control Panel Menu Buttons Back Button Control Pad and Scroll Wheel Numeric Pad ID Button Clear Button Reset Button Stop Button Start Button Main Menu... -
Page 3: Key Contacts
For additional Training on your iR device contact your local Customer Training Consultant on: 0844 892 0844 For printing problems contact the Software Support Centre: 0844 892 0844 To register meter readings and order genuine Canon consumables online, www.canon.co.uk/eservices visit To order genuine Canon consumables via telephone call: 0844 892 0844... -
Page 4: Introduction
Introduction This guide has been designed to provide you, and all users of your Canon iR device(s) within your organisation, with all of the information needed to gain the most out for your investment. The following sections will take you through, in detail, the steps you need to take to produce high quality copies from your iR Multi Functional Printer Copier. -
Page 5: Basic Features
MFD User Guide for Copying Basic Features Original Placement – Platen Glass To be used when copying from books, transparencies, articles that have been cut and pasted together, torn originals or originals smaller than A5. Place original on platen glass face down. ... -
Page 6: Control Panel
MFD User Guide for Copying Control Panel Numeric pad Main Menu Button ID button Copy Button Clear Button Menu Buttons Reset Button Back Button Stop Button Control pad and Start Button scroll wheel Menu Buttons These can be pressed to enter various menus depending on which of the main menu options you are in at the time. -
Page 7: Clear Button
MFD User Guide for Copying Clear Button Select the clear button if you wish to clear any numeric entry made. Reset Button Select the reset button to wipe any settings back to default. Stop Button Select the Stop Button to cancel a job. Start Button Select the Start Button to begin a function –... - Page 8 MFD User Guide for Copying Paper Source Settings The MFP is set to take paper from drawer 1 as default. To choose another source use the right arrow or ‘ok’ to enter the menu to choose drawer 2. Unless paper has already been programmed into the stack bi pass this option will be shadowed out until you drop the media into the stack bi pass at the front of the MFP and follow the on screen prompts to programme in media size and then media type.
- Page 9 MFD User Guide for Copying You can also enter the ‘Layout Settings‘ menu with the right hand menu button, where you can choose if your original orientation is vertical or horizontal to create long or short edge two siding depending on how you would like to read your completed document (choose book type if your document opens like a book and calendar type if your document opens like a calendar).
- Page 10 MFD User Guide for Copying Binding Erase – set Hole Punch Location – this is used when a mark, such as hole punching, is just down one margin of a document. Choose to set the left, right, top or bottom margin as appropriate and set the measurement as highlighted above.
-
Page 11: Send/Fax
Enter Email Use this option to enter a one off email destination you wish to scan to. Enter I-Fax This option is used when sending a fax over the Internet to another Canon i-fax machines. Revised 31 May 2008 Page 11 of 15... -
Page 12: Scan To Store
(resolution, file type, density etc) and hit the green start key to begin the scan. To use pull scan software such as Canon Network Scangear enter the ‘Remote Scan’ menu and turn scanning ‘online’. Put your document in the feeder or on the glass. At your PC use the relevant software to pull the scan into an application then return to the MFP and turn it ‘offline’... -
Page 13: Device Information
Labels and transparencies should always go in the stack bi-pass. Please ensure you only use Canon approved products when using the stack bi-pass. If you are unsure please contact the Canon Consumables department for more information. -
Page 14: 123 Key
MFD User Guide for Copying 123 Key The 123 key is situated on right hand side of the control panel for counter check (meter readings). The serial number of the MFP can also be found in here. Press once to access and once again to exit. Unjamming To unjam a paper jam pull the front door front down using the handle on the front of the MFP. - Page 15 Talk to Canon to improve performance in your business.