ABB AC500-S Safety User Manual page 55

RUN (module
passivation with
a command):
alternating
blinking of
ERR1 & ERR2
LEDs
PROFIsafe communication is up and running. The safety application is running without any
detected errors.
The module and all its channels are passivated because the safety application on the safety
CPU requested a module passivation (activate_FV_C = 1 was set).
The fail-safe value "0" is transferred to the safety CPU for all passivated input channels. All pas-
sivated output channels have a state of "0". The PROFIsafe diagnostic bit(s) for all channels
have the state of "0" to indicate that fail-safe values are transferred.
PROFIsafe status bits in the F-Host for safety I/O module:
FV_activated_S = 1
Process data bits in the safety I/O module process image:
PROFIsafe diagnostic bit = 0
Channel process value = 0
Reintegration request bit = 0
RUN (user
acknowledg-
ment request):
alternating
blinking of
ERR1 & ERR2
LEDs
PROFIsafe communication is up and running. The safety application is running without any
errors but waits for the acknowledgment of a module reintegration (module error is gone).
2020/06/19
Generic safety I/O module behavior > Safety I/O module states
1.0 I0- PWR 2.0I0+ 3.0 I2-
1.1 FE 3.1 FE
2.1
1.2 I1- 2.2I1+ 3.2 I3-
1.3 FE 2.3 3.3 FE
1.4 2.4 3.4
ADDR
2.5
1.5 3.5
x10H
4
3 5
6
2
1.6 2.6 3.6
1 7
0 8
F 9
E A
1.7 2.7 3.7
D B
C
ADDR
1.8 UP 2.8UP 3.8 UP
x01H
4
3 5
2 6
1.9 ZP 2.9ZP 3.9 ZP
1 7
0 8
F 9
E A
D
B
C
ERR1
UP 24VDC 2W
1.0 I0- PWR 2.0I0+ 3.0 I2-
1.1 FE 2.1 3.1 FE
1.2 I1- 2.2I1+ 3.2 I3-
1.3 FE 2.3 3.3 FE
1.4 2.4 3.4
ADDR
2.5
1.5 3.5
x10H
4
3 5
2 6
2.6 3.6
1.6 1 7
0 8
F 9
E A
1.7 2.7 3.7
D
B
C
ADDR
1.8 UP 2.8UP 3.8 UP
x01H
4
3 5
2 6
1.9 ZP 2.9ZP 3.9 ZP
1 7
0 8
F 9
E A
D
B
C
ERR1
UP 24VDC 2W
3ADR025091M0208, 12, en_US
AC500-S safety modules
AI581-S
4.0I2+
4.1
4.2I3+
4.3
4.4
4.5
4.6
4.7
4.8UP
4.9ZP
ERR2
4SAI
Safety Analog Input
AI581-S
4.0I2+
4.1
4.2I3+
4.3
4.4
4.5
4.6
4.7
4.8UP
4.9ZP
ERR2
4SAI
Safety Analog Input
55