YASKAWA GA700 Technical Manual page 562

10.10 H: Terminal Functions
Setting Function
2 Auxiliary
Frequency
Reference 1
3 Auxiliary
Frequency
Reference 2
4 Output Voltage
Bias
5 Accel/Decel Time
Gain
6 DC Injection
Braking Current
7 Torque Detection
Level
8 Stall Prevent Level
During Run
9 Output Frequency
Lower Limit
B PID Feedback
C PID Setpoint
D Frequency Bias
E Motor Temperature
(PTC Input)
F Not Used
10 Forward Torque
Limit
11 Reverse Torque
Limit
12 Regenerative
Torque Limit
13 Torque Reference /
Torque Limit
14 Torque
Compensation
15 General Torque
Limit
16 Differential PID
Feedback
562
V/f CL-V/f OLV CLV AOLV
Sets Reference 2 through multi-step speed reference to enable the command reference
(Auxiliary Frequency Reference 1) from the analog input terminal set here. This value is
a percentage where E1-04 [Maximum Output Frequency] setting is a setting value of
100%.
V/f CL-V/f OLV CLV AOLV
Sets Reference 3 through multi-step speed reference to enable the command reference
(Auxiliary Frequency Reference 2) from the analog input terminal set here. This value is
a percentage where E1-04 [Maximum Output Frequency] setting is a setting value of
100%.
V/f CL-V/f OLV CLV AOLV
Set this parameter to input a bias signal and amplify the output voltage.
V/f CL-V/f OLV CLV AOLV
Enters a signal to adjust the gain used for C1-01 to C1-08 [Accel & Decel Time 1 through
4] if the full scale analog signal (10 V or 20 mA) is 100%.
V/f CL-V/f OLV CLV AOLV
Enters a signal to adjust the current level used for DC Injection Braking if the drive rated
output current is 100%.
V/f CL-V/f OLV CLV AOLV
Enters a signal to adjust the overtorque/undertorque detection level.
Note:
Use this function with L6-01 [Torque Detection Selection 1]. This parameter functions
as an alternative to L6-02 [Torque Detection Level 1].
V/f CL-V/f OLV CLV AOLV
Enters a signal to adjust the stall prevention level during run if the drive rated current is
100%.
V/f CL-V/f OLV CLV AOLV
Enters a signal to adjust the output frequency lower limit level if E1-04 [Maximum
Output Frequency] = 100%.
V/f CL-V/f OLV CLV AOLV
Enters the PID feedback value.
V/f CL-V/f OLV CLV AOLV
Enters the PID setpoint.
V/f CL-V/f OLV CLV AOLV
Enters the bias value added to the frequency reference ifE1-04 [Maximum Output
Frequency] is 100%.
V/f CL-V/f OLV CLV AOLV
Uses the motor Positive Temperature Coefficient (PTC) thermistor to prevent heat
damage to the motor if the current value when the 10 V (or 20 mA) analog signal is input
is 100%.
V/f CL-V/f OLV CLV AOLV
Value for terminals that are not being used or terminals being used in through mode.
V/f CL-V/f OLV CLV AOLV
Enters the forward torque limit if the motor rated torque is 100%.
V/f CL-V/f OLV CLV AOLV
Enters the load torque limit if the motor rated torque is 100%.
V/f CL-V/f OLV CLV AOLV
Enters the regenerative torque limit if the motor rated torque is 100%.
V/f CL-V/f OLV CLV AOLV
Enters the torque reference if the motor rated torque is 100%. This setting is the torque
limit for speed control.
V/f CL-V/f OLV CLV AOLV
Enters the torque compensation value if the motor rated torque is 100%.
V/f CL-V/f OLV CLV AOLV
Enters the torque limit that is the same for all quadrants for forward, reverse, and
regenerative operation if the motor rated torque is 100%.
V/f CL-V/f OLV CLV AOLV
Enters the PID differential feedback value if the full scale analog signal (10 V or 20 mA)
is 100%.
YASKAWA ELECTRIC SIEP C710617 05F YASKAWA AC Drive GA700 Technical Manual
Description
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
Ref.
918
918
918
919
919
920
920
920
920
920
921
921
921
921
922
922
923
923
923
923