YASKAWA GA700 Technical Manual page 559

Setting Function
37 During Frequency
Output
38 Drive Enabled
39 Watt Hour Pulse
Output
3C LOCAL Control
Selected
3D During Speed
Search
3E PID Feedback Low
3F PID Feedback
High
4A During KEB Ride-
Thru
4B During Short
Circuit Braking
4C During Fast Stop
4D oH Pre-Alarm
Reduction Limit
4E Braking Transistor
Fault (rr)
4F Braking Resistor
Overheat (rH)
60 Internal Cooling
Fan Failure
61 Pole Position
Detection
Complete
62 Modbus Reg 1
Status Satisfied
63 Modbus Reg 2
Status Satisfied
65 Standby Output
YASKAWA ELECTRIC SIEP C710617 05F YASKAWA AC Drive GA700 Technical Manual
V/f CL-V/f OLV CLV AOLV
The terminal activates when the drive outputs frequency.
ON : The drive outputs frequency.
OFF : The drive does not output frequency.
V/f CL-V/f OLV CLV AOLV
This terminal activates when the H1-xx = 6A [Drive Enable] terminal activates.
V/f CL-V/f OLV CLV AOLV
Outputs the pulse that shows the watt hours.
V/f CL-V/f OLV CLV AOLV
The terminal activates when the Run command source or frequency reference source is
LOCAL.
ON : LOCAL
OFF : REMOTE
V/f CL-V/f OLV CLV AOLV
The terminal activates when the drive is doing speed search.
V/f CL-V/f OLV CLV AOLV
The activates when the drive detects FbL [PID Feedback Loss].
V/f CL-V/f OLV CLV AOLV
The terminal activates when the drive detects FbH [Excessive PID Feedback].
V/f CL-V/f OLV CLV AOLV
The activates during KEB Ride-Thru.
V/f CL-V/f OLV CLV AOLV
The terminal activates during Short Circuit Braking.
Note:
When A1-02 = 8 [Control Method Selection = EZ Vector Control], this function is
available if you use a PM motor.
V/f CL-V/f OLV CLV AOLV
The terminal activates when the fast stop is in operation.
V/f CL-V/f OLV CLV AOLV
The terminal activates when L8-03 = 4 [Overheat Pre-Alarm Selection = Operate at
Reduced Speed (L8-19)] and oH [Heatsink Overheat] does not clear after the drive
decreases the frequency for 10 cycles.
V/f CL-V/f OLV CLV AOLV
The terminal activates when the internal braking transistor overheats and the drive detects
an rr [Dynamic Braking Transistor Fault] fault.
V/f CL-V/f OLV CLV AOLV
The terminal activates when the braking resistor overheats and the drive detects an rH
[Braking Resistor Overheat] fault.
V/f CL-V/f OLV CLV AOLV
The terminal activates when the drive detects a cooling fan failure in the drive.
V/f CL-V/f OLV CLV AOLV
The terminal activates when drive receives a Run command and the drive detects the
motor magnetic pole position of the PM motor.
V/f CL-V/f OLV CLV AOLV
The terminal activates when the bit specified by H2-08 [Modbus Register 1 Bit Select]
for the MEMOBUS register address set with H2-07 [Modbus Register 1 Address Select]
activates.
V/f CL-V/f OLV CLV AOLV
The terminal activates when the bit specified by H2-10 [Modbus Register 2 Bit Select]
for the MEMOBUS register address set with H2-09 [Modbus Register 2 Address Select]
activates.
V/f CL-V/f OLV CLV AOLV
The terminal deactivates after the drive stops operating and after the time set with b8-51
[Standby Mode Wait Time].
ON : The Run command turns on and the magnetic contactor on the input side turns on.
OFF : The Run command turns off and the drive stops operating. Then, the magnetic
contactor on the input side turns off after the time set with b8-51 [Standby Mode Wait
Time].
Description
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
10.10 H: Terminal Functions
Ref.
906
907
907
907
907
907
908
908
908
908
908
908
908
909
909
909
909
909
10
559