Table of Contents
Advertisement
1K LCSS Drive Belt Tensioners
1.
Remove the 1K LCSS top cover and rear cover,
2.
Remove the relevant belt tensioner:
•
Bin 1 drive belt tensioner,
PL 11.106 Item
•
Intermediate paper drive belt tensioner,
•
Paper output drive belt,
PL 11.120 Item
3.
Remove the E-clip and pulley from the belt tensioner. Apply plastislip grease,
Item 8
to the shaft and pulley bore. Re-assemble the pulley and E-clip on the belt ten-
sioner.
4.
(Bin 1 drive belt tensioner only) Clean off the old lubricant and any contamination from
the belt tensioner and 1K LCSS frame using a micro fiber wiper,
plastislip grease,
PL 26.10 Item
8, to the whole contact face of the belt tensioner.
5.
Reinstall the belt tensioner.
1K LCSS Bin 1 Drive Belt Pulleys and Idler
1.
Remove the 1K LCSS top cover and rear cover,
2.
If necessary, remove the 1K LCSS PWB,
3.
Remove the relevant pulley or idler:
•
Bin 1 drive belt idler,
PL 11.106 Item
•
Bin 1 drive belt pulleys,
PL 11.106 Item
4.
Remove the E-clip and pulley or idler from the belt tensioner. Apply plastislip grease,
26.10 Item 8
to the shaft and pulley or idler bore. Re-assemble the pulley or idler and E-
clip on the belt tensioner.
5.
Reinstall the belt tensioner.
2K LCSS Drive Belt Tensioners
1.
Remove the 2K LCSS top cover and rear cover,
2.
Remove the relevant belt tensioner:
•
Intermediate paper drive belt tensioner,
•
Bin 1 drive belt tensioner,
PL 11.10 Item
3.
Remove the E-clip and pulley from the belt tensioner. Apply plastislip grease,
Item 8
to the shaft and pulley bore. Re-assemble the pulley and E-clip on the belt ten-
sioner.
4.
Clean off the old lubricant and any contamination from the belt tensioner and 2K LCSS
frame using a micro fiber wiper,
PL 26.10 Item
8, to the whole contact face of the belt tensioner.
5.
Reinstall the belt tensioner.
2K LCSS Bin 1 Drive Belt Pulleys and Idler
1.
Remove the 2K LCSS top cover and rear cover,
2.
If necessary, remove the 1K LCSS PWB,
3.
Remove the relevant pulley or idler:
•
Bin 1 drive belt idler,
PL 11.10 Item
•
Bin 1 drive belt pulleys,
PL 11.10 Item
4.
Remove the E-clip and pulley or idler from the belt tensioner. Apply plastislip grease,
26.10 Item 8
to the shaft and pulley or idler bore. Re-assemble the pulley or idler and E-
clip on the belt tensioner.
Repairs/Adjustments
ADJ 4.1
REP
11.1-120.
15.
PL 11.118 Item
14.
8.
PL 26.10
PL 26.10 Item
13. Apply
REP
11.1-120.
REP
11.12-120.
17.
6.
REP
11.1-110.
PL 11.22 Item
17.
13.
PL 26.10
13. Apply plastislip grease,
PL 26.10 Item
REP
11.1-110.
REP
11.14-110.
15.
6.
5.
Reinstall the belt tensioner.
1K and 2K LCSS Bin 1 Elevator Motor Worm and Gear
1.
Remove the 1K LCSS top cover and rear cover,
and rear cover,
REP
11.1-110.
2.
Figure
5, use plastislip grease,
NOTE: The lubrication procedure is the same for the 1K LCSS and the 2K LCSS. The 1K
LCSS is shown in
Figure
5.
PL
Figure 5 Lower vertical slides
PL
May 2013
4-434
REP 11.1-120
or the 2K LCSS top cover
PL 26.10 Item
8, to lubricate the worm and gear.
Apply grease
to the worm
and gear
Xerox® WorkCentre® 5790 Family
Advertisement
Chapters
Table of Contents
