Table of Contents
Advertisement
GP 22 Electrical Power Requirements
Power Requirements
Refer to
Table 1
and
Table
3.
Table 1 Electrical power requirements
Average current
Nominal Voltage
35-55 ppm
110VAC (60Hz)
Less than or equal
Plus 6% minus 10%
to 13.2A RMS.
127VAC (60Hz)
Less than or equal
Plus 6% minus 10%
to 13.2A RMS.
127VAC (60Hz)
Less than or equal
Plus 6% minus 10%
to 13.2A RMS.
120VAC (60Hz)
Less than or equal
Plus 6% minus 10%
to 13.2A RMS.
120VAC (60Hz)
Less than or equal
Plus 6% minus 10%
to 13.2A RMS.
220VAC (50Hz)
Less than or equal
Plus 6% minus 10%
to 10A RMS.
230VAC (50Hz)
Less than or equal
Plus 6% minus 10%
to 10A RMS
240VAC (50Hz)
Less than or equal
Plus 6% minus 10%
to 10A RMS.
Power Save Modes
There are two power save modes which are entered after pre-set timers have expired, low
power mode and sleep mode. Both of these power modes are initially set to factory default time
values but are customer adjustable. Entry to both modes can set by the customer to be either
'job activated' or 'intelligent ready'. The machine will automatically enter low power, then sleep
mode after a period of inactivity exceeds a timer value, refer to
set, the default value for the timer is preset but is adjusted by the machine based on customer
usage.
Configuration
35 ppm
40 ppm
45 ppm
55 ppm
65 ppm
75 ppm
90 ppm
Additional power for 1K LCSS
Xerox® WorkCentre® 5790 Family
65-90 ppm
Comments
Less than or equal
Specific XLA markets only.
to 17.6A RMS.
Less than or equal
Mandatory for Saudi Arabia
to 17.6A RMS.
only.
Less than or equal
To operate at 127VAC +10%
to 17.6A RMS.
for long periods. Mandatory
for Mexico only.
Less than or equal
Run mode, USA and Can-
to 17.6A RMS.
ada.
Less than or equal
Warm up, All 60Hz markets
to 17.6A RMS.
including USA and Canada.
Less than or equal
Europe and other 50Hz
to 10A RMS.
markets.
Less than or equal
Europe and other 50Hz
to 10A RMS.
markets.
Less than or equal
Europe and other 50Hz
to 10A RMS.
markets.
Table
2. If 'intelligent ready' is
Table 3 Power consumption in all modes
Run mode
Standby
(Watt)
(Watt)
Low power (Watt)
1050
290
Less than 125
1050
290
Less than 125
1150
290
Less than 125
1250
290
Less than 125
1550
310
Less than 160
1600
310
Less than 160
1650
310
Less than 160
70
10
0
Low Power Mode
Low power mode is automatically entered after a period of inactivity (determined by timer set-
ting) whilst in standby/ready mode. Timer setting range is from 1 to 120 minutes, refer to
2
for the default settings. Single board controller disk off, IOT +24V disabled, ROS motor off,
fuser to low power. The mode of power is returned to standby following a user request, a key
pressed on the user interface, offline staple button, power switch, document in the DADH,
DADH opened, incoming FAX or print job. Entry into low power mode is controlled by
Sleep Mode
Sleep mode is automatically entered after a period of inactivity (determined by timer setting)
whilst in Low Power Mode. Timer setting range is from 10 to 120 minutes, refer to
the default settings. The mode of power is returned to standby following a user request, a key
press on the user interface, power switch, incoming FAX or print job.
Table 2 Default settings
Standby to low
Speed
power mode (mins.)
35 ppm
1
40 ppm
2
45 ppm
5
55 ppm
8
65 ppm
8
75 ppm
15
90 ppm
15
Power consumption
Refer to
Table 3
for power the consumption of all modes:
Sleep (Watt)
Plug-in/off mode (Watt)
Less than 15
Less than or equal to 0.9
Less than 15
Less than or equal to 0.9
Less than 15
Less than or equal to 0.9
Less than 15
Less than or equal to 0.9
Less than 15
Less than or equal to 0.9
Less than 15
Less than or equal to 0.9
Less than 15
Less than or equal to 0.9
0
0
May 2013
6-53
Low power mode to
sleep mode (mins.)
5
45
45
45
45
45
45
EPA Typical Energy
Consumption Value (Kwh/week)
7.0
9.6
10.7
12.5
13.7
15.8
16.8
N/A
General Procedures/Information
Table
Table 2
for
GP 22
Advertisement
Chapters
Table of Contents
