Xerox WorkCentre 5790 Series Service Manual page 692

– Ground connection to the power supply unit,
– Static eliminator on BM entry.
– Exit brush on HVF top exit, PL
– Static eliminator on BM exit, PL 11.168 Item
– Exit brush on the Tri folder right hand frame,
– Ground wire on the BM compiler motor,
– Ground wire on the BM back stop motor,
– Ground wires to HVF entry and exit feed motors,
– Ground wires to HVF buffer reed and bypass feed motors,
– Ground wire to front of HVF paddle module,
– Ground wire to the HVF offset motor,
– Ground wire to HVF paper pusher motor,
– Ground wire to HVF staple assembly,
– Check that all of the connectors on the HVF PWB, and BM PWB are pushed fully
home. Ensure that all of the ground wires are connected to the frame.
– Where the Tri Folder and the Inserter options are installed check that the PWB con-
nectors are pushed fully home. Ensure that all of the ground wires are connected to
the frame
– Ground wire on the inserter PWB,
– Inserter docking PJ and connector.
– Check all the harnesses for damage and short circuit to ground.
Status Indicator RAPs
OF10, OF11
PL 11.157 Item 1.
PL 11.161 Item 26.
11.155.
16.
PL 11.190.
PL 11.166 Item 4.
PL 11.163 Item 1.
PL 11.150.
PL 11.150.
PL 11.145 Item 2.
PL 11.140 Item 19.
PL 11.145 Item 13.
PL 11.140 Item 14.
PL 11.179 Item 9.
OF11 Waste Toner Contamination RAP
Use this RAP if there is excessive waste toner contamination in the machine or on the cus-
tomer's floor.
Procedure
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to GP
death or injury. Moving parts can cause injury.
Waste toner is being deposited in the waste toner bottle.
Y N
Remove the waste toner bottle and waste toner door,
the bottom of the aperture from where the waste toner bottle was removed, to collect
fallen toner. Enter dC330, code 09-010 photoreceptor motor. Push back the waste toner
shutter, Figure 1, to expose the auger. The auger rotates.
Y N
Install a new main drive module, (35-55 ppm)
Item 1.
Perform the following
• Remove and examine the shutter,
rectly and allows waste toner to reach the bottle. If necessary install a new shutter,
(35-55 ppm) PL 4.15 Item
• Remove the auger damper, (35-55 ppm)
11. Remove the xerographic module. Use a toner vacuum cleaner to remove waste
toner from the duct between the xerographic module and the waste toner bottle. Re-
install all removed components. Monitor the waste toner bottle during subsequent
customer use of the machine.
Waste toner is being deposited in the waste toner bottle
Y N
Install new components:
1. Xerographic module, (35 ppm)
2. Main drive module, (35-55 ppm)
Perform SCP 6 Final Actions.
Check that the waste toner bottle is undamaged and that the waste toner bottle seal,
is undamaged.
If necessary, install new parts:
• Waste toner bottle, PL 9.10 Item
• Shutter assembly, (35-55 ppm)
May 2013
2-660
WARNING
14. Disconnect the power cord. Electricity can cause
REP 9.1. Place a sheet of paper in
PL 4.15 Item 1, (65-90 ppm)
Figure 1. Ensure that the shutter operates cor-
11, (65-90 ppm) PL 4.10 Item 13.
PL 4.15 Item 13, (65-90 ppm)
PL 9.22 Item 2, (40-90 ppm) PL 9.20 Item
PL 4.15 Item 1, (65-90 ppm)
1.
PL 4.15 Item 11, (65-90 ppm) PL 4.10 Item
Xerox® WorkCentre® 5790 Family
PL 4.10
PL 4.10 Item
2.
PL 4.10 Item 1.
Figure 1,
13.