Xerox WorkCentre 5790 Series Service Manual page 676

Table 3 Status messages O to R
Status
UI Message Code Reason for Message
Replace punch head unit 11-540 Punch head present sensor not
made
Replace staple cartridge 11-546 Staple cartridge empty
Replace toner cartridge 09-593 Accumulated toner dispense
time value greater than 27 s
attained, or cycle out event
occurs (Toner cartridge empty).
09-390
Replace tray 5 feed rolls 07-590 The feed head counter has
reached the end of life figure
Replace waste toner bottle 09-594 Waste toner shutdown counter
value attained OR if waste
toner shutdown counter value
greater than 50% and cycle out
event occurs
Replace Xerographic Mod- 09-585 Xerographic module end of life Refer to the
ule
Replace xerographics mod- 09-586 IOT detects an xerographic
ule module failure
Resort and reload all origi- 05-540 DADH document jam is cleared
nals. for a single job
Resort and reload ALL the 05-544 Document jam is cleared (cov-
originals in the document ers cycled and switch cleared)
feeder and 'normal job' or 'build job'
Status Indicator RAPs
OF4b
Reference / Action UI Message
Perform 11-043-110, Restoring configuration set-
11-350-110 RAP for ting. Please wait. System
2K LCSS, 11-044-171 will reboot when com-
to 11-047-171 RAP for pleted.
HVF
Perform 11-364-110 ROS laser not being con-
RAP for 2K LCSS, 11- trolled
364-120 RAP for 1K
ROS system failure. Print-
LCSS, 11-371-171 to
ing is unavailable. If fault
11-377-171 RAP for
persists, call for assistance.
HVF
Touch Ignore Error to use
Install new toner car- other services
tridge. Perform 09-
310, 09-390 RAP
Install new tray 5 feed
UI Message
rolls, PL 8.45 Item 2
'Save job for Reprint' ser-
Install new waste
vice is unavailable. Please
toner bottle, PL 9.10
try again later
Item 1.
03D Soft-
Scan to file unavailable
ware Module Failure
RAP before a new
xerographic module is
installed, (35 ppm) PL
Scanner fault. Please call
9.22 Item 2, (40-90
for assistance
ppm) PL 9.20 Item 2.
Refer to GP 27, End
of Life Extension
Scanner has failed to initai-
Switch the machine
ilize. Switch off the
off and on, GP 14.
machine, wait 3 minutes,
Install a new xero-
then switch on the
graphic module
machine. If fault persists
Replace document on
call for assistance, or press
DADH input tray to
close to use other services
enable recovery.
Check for blanks in
output tray. Resume
or cancel job
Resume job com-
mand is given with
documents replaced
in input tray, if
required, or cancel job
command is given
May 2013
2-644
Table 3 Status messages O to R
Status
Code Reason for Message
03-526 Software upgrade configura-
tion reset
06-540 ROS laser not being controlled. Perform
06-530 ROS system failed.
Table 4 Status messages S to X
Status
Code Reason for Message
17-501 Network controller unavailable
and customer already within
pathway, or CPSR feature sus-
pended
03-585 Fault 03-331 raised
03-543 Single board controller-CCD:
three times retry fail at 100 ms
cycle communication - no
response
14-563 Scanner needs service
Xerox® WorkCentre® 5790 Family
Reference / Action
When the Image pro-
cessing module has
completed restoring
the configuration set-
tings
06-350 RAP
Perform 06-340 RAP
Reference / Action
Wait for the network
controller to become
available. Switch off
the machine then
switch on the
machine, GP 14.
Switch off the
machine then switch
on the machine, GP
14.
Perform 14-310 RAP
and the 03D Software
Module Failure RAP
Switch off the
machine then switch
on the machine, GP
14. Perform 14-110
RAP, 14-310 RAP, 14-
710 RAP