Xerox WorkCentre 5790 Series Service Manual page 1465

Table 6 NVM chain 7
Location NVM Name NVM Description
07-037 T3FeSenClutchOffS HCF (W/TAG
tps steps from the LE at feed
sensor to the clutch de-ener-
gise - TE at nudger A4 LEF.
07-038 HCFNVM7 Reserved for future use
07-039 HCFNVM8 Reserved for future use
07-040 HCFWaitPoint3Step HCF (W/TAG
s steps from HCF exit sensor to
the HCF wait point.
07-041 T3WaitPtRelDelTim HCF (W/TAG
e delay time from PFM sheet
release (sheet ahead) to
sheet being released from
HCF wait point
07-042 FeedMotorOffsteps HCF (W/TAG
steps after the last feed
request between clutch de-
energise and feed motor
stop.
07-043 Sens2HiSpeedCom HCF (W/TAG
pStps steps that the HCF transport
motor stays at delivery speed
after the LE has arrived the
T2 feed sensor.
07-044 DelayTAR4SnsrClrS HCF (W/TAG
tps from TE at HCF exit sensor to
allow the TE to clear tray 4
nip before the feed motor can
change speeds.
07-045 HCFNVM14 Reserved for future use.
07-046 HCFNVM15 Reserved for future use.
07-047 HCFNVM16 Reserved for future use.
07-048 HCFNVM17 Reserved for future use.
07-049 HCFNVM18 Reserved for future use.
07-050 HCFNVM19 Reserved for future use.
07-051 HCFNVM20 Reserved for future use.
07-052 HCFNVM21 Reserved for future use.
07-053 HCFNVM22 Reserved for future use.
07-054 HCFNVM23 Reserved for future use.
07-055 HCFNVM24 Reserved for future use.
07-056 HCFNVM25 Reserved for future use.
07-057 FeedMotorVelocity HCF (W/TAG
feed motor velocity
Xerox® WorkCentre® 5790 Family
Value Default
151) Number of 0 to 2000 35-55 ppm =
260, 65-75
ppm = 215,
90 ppm = 192
- -
- -
151) Number of 0 to 2000 35-75 ppm =
180, 90 ppm
= 220
151) Minimum 0 to 500ms 35 ppm =
250, 40-55
ppm =150,
65-90 ppm =
80
151) Number of 0 to 1000 100
151) Number of 0 to 200 0
151) Step delay 0 to 500 23
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
151) Nominal 200 to 525
1000mm/s
Location NVM Name
07-058 HCFMotorNom-
Speed
07-059 HCFMatchPFM-
Speed
07-060 HCFMatchPFMHiS-
peed
07-061 HCFHiSpeed
07-062 HCFNVM31
07-063 HCFNVM32
07-064 HCFNVM33
07-065 HCFNVM34
07-066 HCFNVM35
07-067 T3FeedWPSteps
07-068 Feed3AcqDelTime
07-069 T3SheetReadyTime HCF
07-070 T3DelayToHiSpeed
Step
07-071 LElateToFeed3Time HCF
07-072 LElateToTAR3Time
May 2013
6-81
Table 6 NVM chain 7
NVM Description Value
HCF (W/TAG 151) Nominal 100 to
HCF transport motor velocity 1000mm/s
HCF (W/TAG 151) Speed that 100 to
HCF transport motor will use 1000mm/s
to match the required PFM
process speed
HCF (W/TAG 151) Speed that 100 to
HCF transport motor will use 1000mm/s
to match the required PFM Hi
speed
HCF (W/TAG 151) HCF 200 to
motor high speed to enable 1000mm/s
catch up and productivity.
Reserved for future use. -
Reserved for future use. -
Reserved for future use. -
Reserved for future use. -
Reserved for future use. -
HCF (W/TAG 151) Number of 0 to 1000
steps past the tray 3 exit sen-
sor to start ramping down the
feed motor.
HCF (W/TAG 151) Tray 3 0 to 2000ms
delay to start sheet acquire
from the tray.
(W/TAG 151) Delay 0 to 2000ms
before sheet is ready to be
sent from tray 3.
HCF (W/TAG 151) Number of 0 to 2000
feed steps from tray 3 TAR to
the feed motor going to high
speed.
(W/TAG 151) Maximum 0 to 3000ms
time the tray 3 clutch is ener-
gised to LE at tray 3 feed
sensor.
HCF (W/TAG 151) Maximum 0 to 6000ms
time the tray 3 clutch is ener-
gised to LE at tray 3 exit sen-
sor.
General Procedures/Information
Default
525
35 ppm =
185, 40-55
ppm =265,
65-90 ppm =
373
35 ppm =
185, 40-55
ppm =265,
65-90 ppm =
685
35-55 ppm
=525, 65-75
ppm =700, 90
ppm = 844
-
-
-
-
-
0
35 ppm =600,
40-45 ppm
=350, 55 ppm
= 250, 65
ppm = 100,
90 ppm = 0
140
260
500
1000
dC131a