Xerox WorkCentre 5790 Series Service Manual page 1466

Table 6 NVM chain 7
Location NVM Name NVM Description
07-073 T3LElateToTAR4Ti HCF (W/TAG
me time from tray 3 feed motor
start, when the sheet is at the
horizontal wait point to the LE
at the HCF exit sensor.
07-074 LElateToFeed4Time HCF (W/TAG
time the tray 4 feed clutch is
energised to LE at tray 4 feed
sensor.
07-075 LElateToTAR4Time HCF (W/TAG
time the tray 4 feed clutch is
energised to LE at HCF exit
sensor,
07-076 HCFNVM45 Reserved for future use.
07-077 Tray4SheetReadyD HCF (W/TAG
elay before sheet ready is sent
tray 4 only.
07-078 T4PreAcquireTime HCF (W/TAG
acquire time for tray 4 (90
ppm only). Timed from LE at
tray 2 feed sensor to start the
acquisition of the next sheet
07-079 HCF(FAR) Pur- HCF(W/TAG
geEnable enable - move sheets to the
left hand door for easier
clearance.
07-080 HCF(FAR) Feed HCF (W/TAG
Retry feed retry attempts.
07-081 FeedMotorOnDelay HCF (W/TAG
clutch energise to starting the
feed motor.
07-082 FeedMotorSlow- HCF (W/TAG
Speed the feed motor runs when the
clutch is disabled (retard roll
geared to run half this
speed).
07-083 HCFNVM52 Reserved for future use.
07-084 HCFNVM53 Reserved for future use.
07-085 HCFNVM54 Reserved for future use.
07-086 HCFNVM55 Reserved for future use.
07-087 HCFNVM56 Reserved for future use.
07-088 HCFNVM57 Reserved for future use.
07-089 HCFNVM58 Reserved for future use.
07-090 HCFNVM59 Reserved for future use.
07-091 HCFNVM60 Reserved for future use.
General Procedures/Information
dC131a
Value Default
151) Maximum 0 to 6000ms 35 ppm =600,
40-55 ppm
=550, 65-90
ppm = 500
151) Maximum 0 to 3000ms 500
151) Maximum 0 to 6000ms 600
- -
151) Delay 0 to 5000ms 20
151) Pre- 0 to 5000 35-75 ppm =
0, 90 ppm =
100
151) Purge 0 = Disable 1
1 = Enabled
151) Number of 0 to 10 5
151) Time from 0 to 10
100000ms
151) Speed that 0 to 100
100000mm/s
- -
- -
- -
- -
- -
- -
- -
- -
- -
Location NVM Name NVM Description
08-001 Print Rate Number of prints per minute
(Controls the IOT print rate).
03-012 must be set to the
same speed.
08-002 Process speed Speed at which sheets
move through machine.
08-003 Machine Model Machine configuration set-
ting.
08-004 Machine Type Machine type setting.
08-005 Machine Quay Machine configuration set-
ting Machine Key.
08-045 Short Cycle Out IOT inactivity shutdown
Time timer (except ROS motor).
08-046 Long Cycle Out Inactivity cycle out timer.
Time
08-047 Abnormal Cycle Abnormal cycle out time.
Out Time
08-048 Top Edge Reg Tray Tray 1 top edge registration
1 Simp simplex.
08-049 Top Edge Reg Tray Tray 2 top edge registration
2 Simp simplex.
08-050 Top Edge Reg Tray Tray 3 top edge registration
3 Simp simplex.
08-051 Top Edge Reg Tray Tray 4 top edge registration
4 Simp simplex.
08-052 Top Edge Reg MSI Bypass tray top edge regis-
Simp tration simplex.
08-059 Top Edge Reg Tray Tray 1 top edge registration
1 Dup duplex.
08-060 Top Edge Reg Tray Tray 2 top edge registration
2 Dup duplex.
08-061 Top Edge Reg Tray Tray 3 top edge registration
3 Dup duplex.
08-062 Top Edge Reg Tray Tray 4 top edge registration
4 Dup duplex.
May 2013
6-82
Table 7 NVM chain 8
Value
0 = 35 ppm
9 = 40 ppm
1 = 45 ppm
2 = 55 ppm
3 = 65 ppm
4 = 75 ppm
6 = 90 ppm
160 to 500
0 to 8
0=Unknown
1=Universal
2=DC
3=MF
4=Spare
0 to 255
0 to 15 seconds 0
0 to 180 sec-
onds
0 to 15 seconds 35-45 ppm=0
7300 to 7700
7300 to 7700
7300 to 7700
7300 to 7700
7300 to 7700
7300 to 7700
7300 to 7700
7300 to 7700
7300 to 7700
Xerox® WorkCentre® 5790 Family
Default
7
35 ppm=179,
40-55 ppm
=257,
65-90
ppm=362
0
0
49
35-45 ppm=0
55-90 ppm =60
55-90 ppm =10
7510
7510
7522
7504
7522
7510
7521
7533
7510