Xerox WorkCentre 5790 Series Service Manual page 1464

Table 6 NVM chain 7
Location NVM Name NVM Description
07-010 LE Late T2 Feed Maximum number of steps
Snr from tray 2 feed motor to LE
at tray 2 feed sensor.
07-011 T1 Buckle Size Number of steps from LE at
tray 1 feed sensor to start of
transport motor.
07-012 T2 Buckle Size Number of steps from LE at
tray 2 feed sensor to start of
tray 1 and 2 transport motor.
07-013 LE Late T1 From T2 Maximum number of steps
from tray 2 TAR nips to LE at
tray 1 feed sensor.
07-014 LE Late Wait Point Maximum number of steps
T1-T2 from tray 1 TAR nips to LE at
wait sensor.
07-015 Wait Point Steps T1- Number of steps from LE at
T4 wait sensor to tray 1 and 2
transport motor stop.
07-016 Release Steps T1- Number of steps the tray 1
T4 and 2 transport motor should
run after the release sheet
command.
07-017 LE Late T2 From Time for the LE of an HCF
T3-T4 sheet to reach the tray 2 feed
sensor.
07-018 Release Steps T5 Distance from wait point to
transport motor releasing
sheet.
07-019 T3 Stack Height Number of steps tray 3 has to
Adjust be lifted above the stack
height sensor for optimum
feed position.
07-020 T4 Stack Height Number of steps tray 4 has to
Adjust be lifted above the stack
height sensor for optimum
feed position.
07-021 LE Late T3 Feed Maximum number of steps
Snr from tray 3 feed motor to LE
at tray 3 feed sensor.
07-022 LE Late T4 Feed Maximum number of steps
Snr from tray 4 feed motor to LE
at tray 4 feed sensor.
07-023 T3 Buckle Size Size of de-skew buckle.
07-024 T4 Buckle Size Size of de-skew buckle.
General Procedures/Information
dC131a
Value Default Location NVM Name
0 to 500 200 07-025
0 to 200 13
07-026
0 to 200 13
07-027
0 to 1200 940
07-028
0 to 1400 1000
07-029
0 to 600 35-55 ppm
=240,
65-90 ppm 07-032
=434
0 to 2000 440
0 to 2000 35-55 ppm =
07-033
1400, 65-90
ppm = 1950
0 to 1000 116
0 to 100 50
07-034
0 to 100 50
07-035
0 to 700 350
07-036
0 to 800 400
0 to 15 3
0 to 15 10
May 2013
6-80
Table 6 NVM chain 7
NVM Description
Release Steps T3- Number of steps the HCF
T4 transport motor should run
after the release sheet com-
mand.
LE Late T4 From T3 Maximum number of steps
from tray 3 TAR nips to LE at
tray 4 feed sensor.
Wait Point Steps T3- Number of steps from tray 4
T4 feed sensor to stop position.
PreRelease Dis- Number of steps for pre-
tance T1 sheet separation.
Tray Media Combi Tray media size sensing
Switch switch to alternate between
old and new switch combina-
tions.
FeedCL4AcqDelayT HCF (W/TAG 151) Delay
ime before feed clutch is enabled
to acquire a sheet
HCFWaitPoint4Step HCF (W/TAG 151) Number of
s HCF tray 4 motor steps from
HCF exit sensor to the HCF
wait point
T4ExSenClutchOffS HCF (W/TAG 151) Number of
tps steps of the tray 4 feed motor
from the LE at HCF exit sen-
sor to tray 4 feed clutch de-
energised
T4RampSteps HCF (W/TAG 151) Number of
steps in the tray 4 feed motor
ramp from/to 525mm/sec.
Used to correct clutch de-
energise time.
T4WaitPtRelDelTim HCF (W/TAG 151) Minimum
e delay time from PFM release
sheet (sheet ahead) to sheet
being released from HCF
wait point.
Value Default
0 to 15 5
0 to 2000 1000
30 to 100 35-55 ppm =4
0,
65-90 ppm =
53
100 to 150 130
0=Old 1
combination1
=New combi-
nation
0 to 6000ms 35 ppm =
400, 40-45
ppm =250, 55
ppm = 50, 65
ppm = 100,
75 ppm = 60,
90 ppm = 0
0 to 2000 35 ppm =
180, 40-55
ppm =140,
65-75 ppm =
200, 90 ppm
= 230
0 to 1000 342
0 to 500 54
0 to 500ms 35-45 ppm =
250, 55 ppm
=150, 65-75
ppm = 110,
90 ppm = 80
Xerox® WorkCentre® 5790 Family