Functions Added In Multi Program 2; Mode - Sony MVS-8000X User Manual

Assigning sub bank preview output to
buttons
The "Sub Preview" utility command on each switcher
bank can be assigned to the following buttons.
• 1st row and 2nd row buttons on the cross-point control
block in utility/shotbox mode
• Memory recall buttons in the utility/shotbox control
block
• User preference buttons in the menu panel
For details, see "Settings Relating to Button Assignment"
(page 418).
Changing the matrix size to standard
When using a router, if the matrix size is set to [128×128],
it is not possible to control the utility 3 bus on the S-Bus.
When using Multi Program 2, select a size other than
[128×128] in the <Matrix Size> group of the Engineering
Setup >Router/Tally >Router menu (7361).
For details, see "Assigning Switcher Inputs/Outputs to S-
Bus Space" (page 470).
If [136×138] is selected in the <Matrix Size> group, the
bus number of the DME Key bus is used as the bus number
of the utility 3 bus.
No. Bus (Standard)
70 M/E-1 DME Key
85 M/E-2 DME Key
100 M/E-3 DME Key
115 P/P DME Key
Making settings for keyframe timeline
operation
To assign a sub bank region to a region selection
button in the numeric keypad control block
In the Engineering Setup >Panel >Config >10 Key Region
Assign menu (7321.7), assign sub bank region to the
region selection button in the numeric keypad control
block.
For details, see "Assigning a Region to the Region
Selection Buttons in the Numeric Keypad Control Block"
(page 410).
To select a region or reference region using the
menu
During snapshot or keyframe operations, you can select a
region (including sub bank) in the Key Frame >Region
Select menu (6117).
This is convenient for selecting some of the regions
assigned to the numeric keypad control block or changing
the reference region.
Bus (MP2)
M/E-1 Utility3
M/E-2 Utility3
M/E-3 Utility3
P/P Utility3
201
For details, see "Recalling regions to edit (menu)"
(page 309).
To assign regions shown in the timeline menu
The timeline and other information is displayed for each
region assigned in the numeric keypad control block in the
Key Frame >Time Line menu (6111).
You can set the display method in the Key Frame
>Timeline Assign menu (6115).
For details, see "Timeline Menu Display Settings"
(page 306).
Enabling re-entry between main and sub
In the Engineering Setup >Switcher >Config menu (7331),
press [MP2 Free Re-Entry], turning it on.
Re-entry between main and sub on the same switcher bank
is enabled.
Notes
• Re-entry adds a 1H delay to the video. Looped re-entry
may cause problems in the video.
• On the MVS-8000X, a maximum of ten re-entry stages
are supported, with the final output having a delay of 5H.
On the MVS-7000X, a maximum of twelve re-entry
stages are supported, with the final output having a delay
of 6H.
• The selection order of re-entry signals affects the
number of lines by which the output signal is lowered.
• If a delay occurs in the image, even when through mode
is set, the ancillary data does not pass through.
• For example, it is possible to select re-entry of M/E-1
main on M/E-1 main.
Restrictions on re-entry when using Multi
Program 2
Snapshots are affected by the re-entry function.
When [MP2 Free Re-Entry] is enabled, the following
restrictions apply when a switcher bank is in Multi
Program 2 mode.
If you save and recall snapshots simultaneously with more
than one region specified, the recorded state is reproduced
in the order of precedence of regions (M/E-1 >M/E-2 >M/
E-3 >M/E-4 >M/E-5 >PGM/PST). Therefore, if you save
and recall a snapshot with more than one region specified,
the cross-point settings may not be recalled correctly.
To recall a snapshot correctly, press the cross-point button
before recalling the snapshot, to select a signal other than
the re-entry signal, then recall the snapshot.

Functions Added in Multi Program 2

Mode

• You can set the video process for the utility 3 bus signal.