Sony MVS-8000X User Manual page 552

Icon Message
Still frame on FM 2nd board (–51).
Clip frame number can't be ODD in
720P format (–52).
File Frame Memory
Some requests are skipped.
Following operation is not permitted.
– Loading that will cause duplicate
register name.
File Open Status
ERROR (01)
ERROR (02)
ERROR (FF): No target device has
been assigned
Format
Success!!
But some partitions cannot be created
because the capacity of the local drive
is not enough.
Failure.
Local drive device is busy.
In order to complete local drive format,
System needs to be restarted and
formatted again.
System will be restarted, then please
execute local drive format again.
Failure.
Make sure of the removable drive.
GPI Input
Please set Target.
Please set Trigger Type.
Please set Reg No.
Please set Aux Bus No.
Please set Src No.
GPI Output
Please set Target.
Please set Trigger Type.
Please set Reg No.
Please set Pulse Width.
Please set Pulse Timing.
HDD Format
No external HDD was found (–2).
Format operation failed (–11).
Description
2542: Frame Memory >File >Auto Extraction
When [Extraction Start] was pressed, a still image was extracted from an
external clip.
2542: Frame Memory >File >Auto Extraction
When [Extraction Start] was pressed, an odd number of clips were extracted
(720P format only).
7151: File >Frame Memory >Frame Memory
7162: File >All, External File >Import/Export
An attempt was made to load a file with the same name as a file already in
the register.
533X: Device >DDR/VTR
An error was returned from the DDR/VTR, and one of the messages on the
left appears, depending on the error number.
Check the device settings in menu 7355 (Engineering Setup >DCU >Serial
Port Assign) or menu 7325.4 (Engineering Setup >Panel >Device Interface
>Device Assign).
7317: Engineering Setup >System >Maintenance
Formatting of the local drive was completed successfully.
However, because of insufficient local drive capacity, only the possible
number of partitions were created.
7317: Engineering Setup >System >Maintenance
Formatting of the local drive terminated abnormally.
If the local drive is functioning correctly, or in some cases when there is
damage to the local drive, it may not be possible to format the local drive
correctly in a single attempt. In such cases, it is necessary to restart the
system, and then carry out formatting again.
Press [OK] to restart the system.
7317: Engineering Setup >System >Maintenance
Formatting of the removable drive terminated abnormally. Check that the
removable drive is connected correctly.
7337.2/3: Engineering Setup >Switcher >Device Interface >GPI Input
7344.1/2: Engineering Setup >DME >Device Interface >DME1 GPI Input
7344.4/5: Engineering Setup >DME >Device Interface >DME2 GPI Input
7344.7/8: Engineering Setup >DME >Device Interface >DME3 GPI Input
7344.10/11: Engineering Setup >DME >Device Interface >DME4 GPI Input
7352/7352.1: Engineering Setup >DCU >GPI Input Assign
An incorrect parameter setting value was specified. Check the settings, and
try again.
7337.4: Engineering Setup >Switcher >Device Interface >GPI Output
7344.3: Engineering Setup >DME >Device Interface >DME1 GPI Output
7344.6: Engineering Setup >DME >Device Interface >DME2 GPI Output
7344.9: Engineering Setup >DME >Device Interface >DME3 GPI Output
7344.12: Engineering Setup >DME >Device Interface >DME4 GPI Output
7354: Engineering Setup >DCU >GPI Output Assign
An incorrect parameter setting value was specified. Check the settings, and
try again.
2561: Frame Memory >External Device >Ext HDD Format
When [5 Partition] or [15 Partition] was pressed, the external HDD could not
be found. Check that the external HDD is connected correctly.
2561: Frame Memory >External Device >Ext HDD Format
When [5 Partition] or [15 Partition] was pressed, formatting of the external
HDD failed.
550