Setting The Display Mode - Sony MVS-8000X User Manual

2
Enter a name of up to 12 characters in the keyboard
window, and press [Enter].
Note
Lower case characters may be entered, but the entered
characters are displayed as upper case characters on
the buttons in the cross-point Flexi Pad.
About re-entry button assignment
The following re-entry buttons can be assigned to buttons
on the cross-point Flexi Pad.
• n-ROW P/P PGM1, n-ROW M/E-1 PGM1 to n-ROW
M/E-5 PGM1 (n = 1 to 4)
• n-ROW P/P PGM2, n-ROW M/E-1 PGM2 to n-ROW
M/E-5 PGM2 (n = 1 to 4)
The button numbers and video/key pair numbers of re-
entry buttons is fixed to the following.
Button name Button V/K pair
(n = 1 to 4) numbe number
r
n-ROW P/P 284 124
PGM1
n-ROW M/E- 281 121
1 PGM1
n-ROW M/E- 282 122
2 PGM1
n-ROW M/E- 283 123
3 PGM1
n-ROW M/E- 285 129
4 PGM1
n-ROW M/E- 286 131
5 PGM1
n-ROW P/P 294 128
PGM2
n-ROW M/E- 291 125
1 PGM2
n-ROW M/E- 292 126
2 PGM2
n-ROW M/E- 293 127
3 PGM2
n-ROW M/E- 295 130
4 PGM2
n-ROW M/E- 296 132
5 PGM2
The re-entry video/key numbers are set as the pair numbers
by default. Use the defaults as-is, since changing the
settings will make it impossible to select the correct
signals.
Setting the HOME page of the cross-point
Flexi Pad
This sets the page that is displayed when the [HOME]
button on the cross-point Flexi Pad is pressed.
V default K default
setting setting
P/P OUT1 P/P OUT1
M/E-1 OUT1 M/E-1 OUT1
M/E-2 OUT1 M/E-2 OUT1
M/E-3 OUT1 M/E-3 OUT1
M/E-4 OUT1 M/E-4 OUT1
M/E-5 OUT1 M/E-5 OUT1
P/P OUT6 P/P OUT6
M/E-1 OUT6 M/E-1 OUT6
M/E-2 OUT6 M/E-2 OUT6
M/E-3 OUT6 M/E-3 OUT6
M/E-4 OUT6 M/E-4 OUT6
M/E-5 OUT6 M/E-5 OUT6
431
1
In the <Xpt Flexi Pad> group of the Engineering Setup
>Panel >Operation >Xpt Module Operation menu
(7326.12), press [Home Page Set].
2
Enter the page number to set (1 to 14) using the
numeric keypad window, then press [Enter].

Setting the display mode

This sets the information that appears on the display of the
cross-point control block/AUX bus control block.
The display content and format can be selected for each of
six types of display mode.
1
In the Engineering Setup >Panel >Operation >Xpt
Module Operation menu (7326.12), press [Display
Mode Setting].
The Display Mode Setting menu (7326.15) appears.
The left side shows six display modes, and the right
side shows a list of items to display.
2
In the <Bank Select> group, select the target bank to
set.
3
Select the target display mode to set.
4
To divide the display into upper/lower to display two
pieces of information, press [Split], turning it on.
5
In the list on the right, select the item to display.
6
Perform the following operations.
When [Split] is not lit, press [Set] in the <Lower Area>
group.
When [Split] is lit, press [Set] in the <Upper Area>
group to set the display in the upper area, and in the
<Lower Area> group to set the display in the lower
area.
To rename a display mode
The specified name is displayed on the display mode
buttons in the cross-point Flexi Pad used for display mode
selection.
1
Select the target display mode to set, and press
[Name].
2
Enter a name of up to 12 characters in the keyboard
window, and press [Enter].
Note
Lower case characters may be entered, but the entered
characters are displayed as upper case characters on
the buttons in the cross-point Flexi Pad.