Basic Dme Wipe Setting Operations; Selecting A Dme Wipe Pattern - Sony MVS-8000X User Manual

Basic DME Wipe Setting
Operations
You carry out DME wipe setting operations using the
DME Wipe menu for each bank.
This section describes operations on the M/E-1 bank (M/
E-1 >DME Wipe menu) as an example.
For details about independent key transition DME wipe
settings, see "Basic Independent Key Transition DME
Wipe Setting Operations" (page 147).

Selecting a DME Wipe Pattern

1
Display the DME wipe setting menu.
In 1-channel mode, open the M/E-1 >DME Wipe >1ch
menu (1161).
In 2-channel mode, open the M/E-1 >DME Wipe >2ch
menu (1162).
In 3-channel mode, open the M/E-1 >DME Wipe >3ch
menu (1163).
2
Press the button for the desired DME wipe pattern
group to select it.
The patterns from the selected pattern group appear on
the screen.
If executing a DME wipe using a resizer
Select [Resizer Slide], [Resizer Squeeze], or [Resizer
Frame I/O] in the DME wipe pattern group.
Resizer DME wipes can be used only when the next
transition event is a key.
3
Press the desired pattern to select it.
Adjusting DME wipe pattern parameters
Of the DME wipe patterns, the following have parameters
that can be adjusted.
When Brick (for two channels) is selected
(pattern numbers 2801 to 2804, 2811 to 2814)
No. Parameter Adjustment
1 Side V Size X Horizontal scaling factor
2 Side V Size Y Vertical scaling factor
3 Height Height of brick
4 Center X Horizontal center position
Vertical center position
5 Center Y
a) The horizontal center position of the video pasted on Side V. At –100.00,
the center is at the left edge of the screen. At +100.00, the center is at the
right edge of the screen.
b) The vertical center position of the video pasted on Side V. At –100.00, the
center is at the bottom edge of the screen. At +100.00, the center is at the
top edge of the screen.
When Frame in-out (for two channels) is selected
• Pattern numbers 2851 to 2854
No. Parameter
5 Delay
• Pattern numbers 2861 to 2864
No. Parameter
1 Rot X
2 Rot Y
3 Rot Z
5 Delay
When Brick (for three channels) is selected
(pattern number 3601)
No. Parameter
1 Side V Size X Side V horizontal scaling factor
2 Side V Size Y Side V vertical scaling factor
3 Height
4
Side V
Center X
5 Side V
Center Y
a) Common with the [Height] parameter in group 2.
b) The horizontal center position of the video pasted on Side V. At –100.00,
the center is at the left edge of the screen. At +100.00, the center is at the
right edge of the screen.
c) The vertical center position of the video pasted on Side V. At –100.00, the
center is at the bottom edge of the screen. At +100.00, the center is at the
top edge of the screen.
No. Parameter
1 Side H Size X Side H horizontal scaling factor
2 Side H Size Y Side H vertical scaling factor
3 Height
4 Side H
Center X
5
Side H
Center Y
a)
a) Common with the [Height] parameter in group 1.
b) The horizontal center position of the video pasted on Side H. At –100.00,
b)
the center is at the left edge of the screen. At +100.00, the center is at the
right edge of the screen.
143
Adjustment
Timing for video selected on a utility
bus to appear on the screen
Adjustment
Rotation on the Y axis (horizontal
direction)
Rotation about the X axis (vertical
direction)
Rotation about the Z axis
Timing for video selected on a utility
bus to appear on the screen
Parameter group [1/2]
Adjustment
a)
Height of brick
Side V horizontal center position
Side V vertical center position
Parameter group [2/2]
Adjustment
a)
Height of brick
Side H horizontal center position
Side H vertical center position
b)
c)
b)
c)