Sony MVS-8000X User Manual page 465

Multi format switcher system with icp-x7000 integrated control panel.
Hide thumbs Also See for MVS-8000X:
Table of Contents

Advertisement

Frame Freeze, FM Src1 Freeze Off, FM Src2 Field
Freeze, FM Src2 Frame Freeze, FM Src2 Freeze Off, FM
Src1 Clip Record, FM Src1 Clip Stop, FM Src2 Clip
Record, FM Src2 Clip Stop, FM1 to FM8 Clip Cueup,
FM1 to FM8 Clip Play, FM1 to FM8 Clip Stop, Shotbox
? Recall, Macro Take, Macro ? Recall, No Action
Aux ? O'ride Src ??
2)
• When the trigger type is "Level"
System Format, System Aspect, M/E-x Aspect, P/P
Aspect, DME Ch1 Aspect, DME Ch2 Aspect, DME Ch3
Aspect, DME Ch4 Aspect, DME Ch5 Aspect, DME Ch6
Aspect, DME Ch7 Aspect, DME Ch8 Aspect, Level
Enable, Panel Status, No Action
1) M/E-x: where x is the M/E number (1 to 5)
Keyx: where x is the key number (1 to 8)
DSKx: where x is the DSK number (1 to 8)
2) When the trigger type is only "Rising Edge" or "Falling Edge"
Notes
• "Level Enable" is a function that determines whether
GPI inputs are enabled ("Enable") or disabled
("Disable") for the "System Aspect" and "System
Format" actions that can be used when the trigger type is
"Level." If the input is disabled ("Disable") when "Level
Enable" is selected, "System Aspect" and "System
Format" cannot be switched by the GPI input.
If a GPI action is triggered just as system power is turned
off, such as by switching "System Aspect" or "System
Format," the action may be executed immediately before
the power goes off and the power may go off before the
action is completed. This may corrupt the setup. It is
therefore recommended to use "Level Enable" to avoid
such a situation.
• "Aux ? O'ride Src ??" switches the AUX bus input. For
example, when "Rising Edge" is selected, the configured
AUX bus input is used on the rising edge and then
returns to the original cross-point on the falling edge. If
the GPI trigger is applied repeatedly at short intervals
(0.5 seconds or less), the cross-point switching may not
be carried out correctly. In this case, apply the GPI
trigger again.
• When using the format converter with "Action" set to
"System Format," you can set the conversion format of
the format converter for "FC Input 1-4," "FC Input 5-8,"
"FC Input 9-12" (MVS-8000X only), "FC Input 13-16"
(MVS-8000X only), "FC Output 1-2," and "FC Output
3-4."
• In Dual Simul mode, you can select the target switcher
for the panel status display using "Panel Status"
(H=SWR1, L=SWR2).
Configuring level settings
Configure the settings for low level and high level when
the trigger type is set to "Level."
1
In the Engineering Setup >DCU >GPI Input Assign
menu (7352), select an action and press [H/L Set].
The H/L Set menu (7352.1) appears.
2
Select the setting.
No.
Parameter Adjustment
2
Item No
3
To trigger an action when the input is high level or low
level, press [H Set] or [L Set], respectively.
If the action is "System Format," press [H Set] or [L
Set] in the <System> group.
To set the level for the format converter
1
Select the "System Format" action in step 4 in
"Configuring GPI Inputs" (page 462).
The format converter list appears.
2
Select the target format converter to set
3
Refer to step 2 in "Configuring level settings"
(page 463) and select a setting (signal format).
4
In the <FC Input/Output> group, press [H Set] or [L
Set].
463
Selection of setting for action

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents