Sony MVS-8000X User Manual page 48

Name Description
1st row When the [2ND DELEG] button is
lit:
Selects a bus to assign in the 3rd
row.
When the [2ND DELEG] button is
not lit:
• Selects a bus to assign in the 3rd
row and 4th row.
• You can select a bus on the
shifted state of a delegation
button while pressing the [SHIFT]
button.
2nd row When the [2ND DELEG] button is
lit:
Selects a bus to assign in the 4th
row.
When the [2ND DELEG] button is
not lit:
• Selects a bus to assign in the 3rd
row and 4th row.
• You can select only a bus on the
shifted state of a delegation
button in the 2nd row.
3rd row When the [2ND DELEG] button is
lit:
Selects a signal on the bus
selected in the 1st row.
When the [2ND DELEG] button is
not lit:
• Selects a signal on the bus
selected in the 1st row or 2nd
row.
• You can select a bus on the
shifted state of a button while
pressing the [SHIFT] button.
4th row When the [2ND DELEG] button is
lit:
Selects a signal on the bus
selected in the 2nd row.
When the [2ND DELEG] button is
not lit:
Selects a signal on the shifted state
of the bus selected in the 1st row or
2nd row.
a) For DME1 V/K to DME8 V/K buses, the front of the image is selected.
While a delegation button is pressed, the rear of the image is selected.
Delegation button/cross-point button numbers
The button numbers are labeled on the delegation/cross-
point buttons.
For details, see "Button numbers in the AUX bus control
block" (page 72).
SHIFT button
The [SHIFT] button function is assigned to the button on
the right-hand end, and is used to toggle between the
shifted and unshifted states of the button row.
a)
a)
a)
48
The operation of the [SHIFT] button in second delegation
mode can be set to one of the following modes in the Setup
menu.
• The shifted state is selected while the button is pressed
(hold mode).
• Every time the button is pressed, it toggles between
shifted and unshifted states (lock mode).
For details, see "Setting the AUX Bus Block" (page 417).
Cross-point hold function
Setting cross-point hold enables you to recall a keyframe
or snapshot while keeping the current cross-point selection
unchanged.
To set cross-point hold for the bus selected in the 1st row/
2nd row, press the [XPT HOLD] button or [2ND XPT
HOLD] button on the cross-point Flexi Pad, turning it on.
KEY button and 2ND KEY button
When an operation mode that allows you to select both a
key signal and video signal is set in the Setup menu, the
[KEY] button and [2ND KEY] button on the cross-point
Flexi Pad are enabled.
When a cross-point button on the 3rd/4th row is pressed
while pressing the [KEY] button, the key signal is selected.
When a cross-point button on the 3rd/4th row is pressed
without pressing the [KEY] button, the video signal is
selected.
When second delegation mode is set, use the [KEY] button
to select the signal on the 3rd row, and the [2ND KEY]
button to select the signal on the 4th row.
Information for the key signal or video signal, whichever
is selected, appears on the display.
For details, see "Setting the Button Operation Mode"
(page 428).
b Display
Six types of display mode can be selected, according to the
information to display. The display mode is switched using
the [DISP 1: XXX] to [DISP 6: XXX] (where XXX is the
mode name) display mode buttons on the cross-point Flexi
Pad.
The following information can be shown on the display.
• Settings of buttons on the 1st row to 4th row (bus name,
signal name)
• Macro register name of macro attachment assigned to
the 3rd to 4th row buttons
Notes
• When the [SHIFT] button function is set, "SHFT"
appears on the display. When the shifted state is selected,
"SHFT" is highlighted in reverse video, and the button
information also toggles to show the shifted display.
• When the [DEST] button is pressed on the cross-point
Flexi Pad, turning it off, the 1st row and 2nd row