Fitting The Side Guide Timing Belt For The Manual Feed Tray Assembly(Ir105); Fitting The Side Guide Timing Belt For The Manual Feed Tray Assembly; Manual Pickup Roller; Removing The Pickup Roller - Canon ImageRunner iR8500 Series Service Manual

Chapter 9
5) Remove the screw [4], and detach the connector cover [5].
6) Disconnect the connector [6], and detach the manual feed tray unit [1]
upward while it is kept open at about 90 deg.
[2] [3]
[5]
[4]
9.10.6.2 Removing the Manual Feed Tray Unit
/ iR85+ / iR8070
1) Remove the upper right cover.
2) Open the manual feed tray unit [1].
3) Remove the screw [2], and detach the door tape [3] from the machine
side.
4) Remove the screw [4], and detach the connector cover [5].
5) Disconnect the connector [6], and detach the manual feed tray unit [1]
upward while it is kept open at about 90 deg.
[2] [3]
[5]
[4]
9.10.6.3 Fitting the Side Guide Timing Belt for the Manual
Feed Tray Assembly(iR105)
iR105
1) Butt the rack plate [1] of the manual feed tray against section A (in
open state).
2) Move the slide volume [2] in the direction of B, and fit the timing belt
[3] to the pulley [4] and the pulley [5].
[3]
[4]
[2]
9-60
[1]
[6]
F-9-99
0008-8178
[1]
[6]
F-9-100
0007-2790
[5]
[1]
A
B
F-9-101
9.10.6.4 Fitting the Side Guide Timing Belt for the Manual
Feed Tray Assembly
iR105i/iR105+ / iR9070 / iR85+ / iR8070
1) Butt the rack plate [1] of the manual feed tray against section A (in
open state).
2) Move the slide volume [2] in the direction of B, and fit the timing belt
[3] to the pulley [4] and the pulley [5].
[3]
[4]
[2]

9.10.7 Manual Pickup Roller

9.10.7.1 Removing the Pickup Roller

iR105i/iR105+ / iR9070 / iR85+ / iR8070
1) Open the manual tray paper guide.
2) Remove the left/right stop rings [1] (two each), shutters [2] (two
each), spacers [3] (two each), and rolls [4] (two each).
[1] [2]
If the multifeeder is used during installation or if the multifeeder has not
been used for a long time, pickup can fail. If such happens, detach the
protective sheet from the sponge roller, and dry wipe the sponge roller.

9.10.7.2 Mounting the Pickup Roller

iR105i/iR105+ / iR9070 / iR85+ / iR8070
Mount the pickup roller by reversing the steps used to remove it with the
following in mind:
- The front pickup roller and the rear pickup roller are not
interchangeable.
- The front pickup roller is identified by its silver- colored collar.
When mounting the pickup roller [1] to the pickup assembly, be sure
that the round marking [2] on the collar (silver) is toward the
machine's front,
- The rear pickup roller is identified by its gold collar.
When mounting the pickup roller [3] to the pickup assembly, be sure
that the round marking [4] on the side of the roller and the round
marking [5] on its collar (gold) are toward the machine's rear.
0008-8180
[5]
[1]
A
B
F-9-102
0007-1271
[1]
[2]
[3]
[4]
[4]
[3]
F-9-103
0007-1272