Download  Print this page

Advertisement

Portable Manual
iR2030/2025/2022/2018 Series
Aug 8 2007

Advertisement

Table of Contents

   Summary of Contents for Canon iR2030

  • Page 1 Portable Manual iR2030/2025/2022/2018 Series Aug 8 2007...
  • Page 3 Canon will release technical information as the need arises. In the event of major changes in the contents of this manual over a long or short period, Canon will issue a new edition of this manual.
  • Page 4 Introduction Symbols Used This documentation uses the following symbols to indicate special information: Symbol Description Indicates an item of a non-specific nature, possibly classified as Note, Caution, or Warning. Indicates an item requiring care to avoid electric shocks. Indicates an item requiring care to avoid combustion (fire). Indicates an item prohibiting disassembly to avoid electric shocks or problems.
  • Page 5 Introduction The following rules apply throughout this Service Manual: 1. Each chapter contains sections explaining the purpose of specific functions and the relationship between electrical and mechanical systems with refer- ence to the timing of operation. In the diagrams, represents the path of mechanical drive; where a signal name accompanies the symbol , the arrow indicates the direction of the electric signal.
  • Page 7: Table Of Contents

    3.2.2Jam Codes (Related to Finisher) ......................10 3.2.3Jam Codes (Related to ADF)........................10 3.2.4Jam Codes (Related to Duplex Unit) ......................10 3.2.5Jam Codes (Related to Inner 2-way Tray)....................11 Chapter 4 User Mode Items 4.1 User Mode Items..............................13 4.1.1Common Settings (iR2030i/iR2030/iR2025i/iR2025/iR2022i/iR2018i) ..........13 4.1.2Timer Settings (iR2030i/iR2030/iR2025i/iR2025/iR2022i/iR2018i) .............13 4.1.3Adjustment/Cleaning (iR2030i/iR2030/iR2025i/iR2025/iR2022i/iR2018i) ..........14...
  • Page 8 4.1.6Copy Settings (iR2030i/iR2030/iR2025i/iR2025/iR2022i/iR2018i)............15 4.1.7Communication Settings (iR2030i/iR2030/iR2025i/iR2025/iR2022i/iR2018i) ........15 4.1.8Printer Settings (iR2030i/iR2030/iR2025i/iR2025/iR2022i/iR2018i) ........... 16 4.1.9Address Book Settings (iR2030i/iR2030/iR2025i/iR2025/iR2022i/iR2018i) ........17 4.1.10Recommended setting of system management information.............. 18 4.1.11The Reference Information of the Department ID Management ............18 Chapter 5 Service Mode 5.1 Fax System Service Mode..........................
  • Page 9 Contents 5.1.3.12 <024: pseudo RBT transmission level at time of fax/tel switchover> ........29 5.1.3.13 <025: Answering machine connection function signal detection time> ........29 5.1.3.14 <027: V.21 low-speed flag preamble identification length> ............29 5.1.3.15 <055: Acquisition period of environmental log data> ..............29 5.1.3.16 <056 - 061: Count type select >...
  • Page 10 Contents 5.1.9.2 Method of confirming license option ....................45 5.1.9.3 Inactivity of the transmitted license ....................45 5.1.10 eRDS Parameter Settings (E-RDS)....................... 46 5.1.10.1 Settings Related to e-RDS ......................46 5.1.11 Display of Counter Information (COUNTER) ..................46 5.1.11.1 Counters ............................. 46 5.1.11.2 Clearing Counters ..........................
  • Page 11 7.1.4Pickup/Delivery/Original Handling Accessories System Configuration (iR2022i/iR2022K/iR2025i/ iR2030i) ................................83 7.1.5Reader Heater/Cassette Heater System Configuration (iR2018/iR2022/iR2022N)......84 7.1.6Reader Heater/Cassette Heater System Configuration (iR2018i) ............85 7.1.7Reader Heater/Cassette Heater System Configuration (iR2022K/iR2022i/iR2025/iR2025i/iR2030/ iR2030i) ................................86 7.1.8Printing/Transmitting Accessories System Configuration (iR2018/ir2022/iR2022N) ......87 7.1.9Printing/Transmitting Accessories System Configuration (iR2018i/iR2022i/iR2022K/iR2025/ iR2025i/iR2030/iR2030i)..........................88...
  • Page 13: Chapter 1 Maintenance And Inspection

    0017-5958 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i The machine has parts that must be replaced on a periodical basis to ensure a specific level of functional performance. (The loss of the function of any of these parts will significantly affect the machine performance, regardless of the presence/absence of external changes or damage.)
  • Page 14: Scheduled Servicing Basic Procedure

    1.3.1 Scheduled Servicing 0017-5969 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i The reader and printer unit does not have items that require scheduled servicing. Be sure to clean the copyboard glass and the ADF reading glass during every service visit.
  • Page 15: Chapter 2 Standards And Adjustments

    (With ADF) operation panel of the host machine. 0017-5981 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i 2) Using the arrow keys on the operation panel, display "TEST MODE". 3) Press the OK key. After replacing the copyboard glass, enter the correction values (X, Y, Z) of 4) Press the 2 key.
  • Page 16: 3procedure After Replacing The Usb Memory (touch Panel Type)

    2.3.4 Actions to Take before All Clearing (Backing up the User Data) 0017-5986 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i - Performing the all-clear operation in the service mode (#CLEAR > ALL) erases/initializes the user data such as address data and user mode settings.
  • Page 17 Chapter 2...
  • Page 19: Chapter 3 Error Code

    Chapter 3 Chapter 3 Error Code 3.1 Error Code Details 3.1.1 Error Code Details 0017-6037 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i T-3-1 Display Detail Code Main Cause/Symptom Countermeasure Code E000 0000 Startup error The temperature detected by the main or sub thermistor does - Check the fixing film connector.
  • Page 20 Chapter 3 Display Detail Code Main Cause/Symptom Countermeasure Code E196 0001 Image processor PCB failure Error on writing and readout ROM of image processor PCB - Putting the switch on/off of the power supply. (mainn ROM). - Replace the image processor PCB. 0002 Image processor PCB failure Error on writing and readout ROM of image processor PCB...
  • Page 21 Chapter 3 Display Detail Code Main Cause/Symptom Countermeasure Code E744 Language file/boot ROM/USB memory error 0001 The language file version does not match Bootable. Download a language file of the correct version. 0002 The language file is longer than the permitted size. Download a language file of the correct version.
  • Page 22: Jam Code

    Chapter 3 3.2 Jam Code 3.2.1 Jam Codes (Related to Printer Unit) 0017-6038 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i T-3-2 Code Name Sensor No. Description 0104 Delay jam in paper SR209 The registration sensor cannot detect the leading edge of paper from the moment paper pickup starts to the pickup section moment the jam detection time is reached.
  • Page 23: 5jam Codes (related To Inner 2-way Tray)

    The duplex paper sensor 2 does not turn off when the specified time has lapsed since the feed motor started. 3.2.5 Jam Codes (Related to Inner 2-way Tray) 0017-6042 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i T-3-6 Code Name Sensor No.
  • Page 24 Chapter 3...
  • Page 25: Chapter 4 User Mode Items

    Chapter 4 Chapter 4 User Mode Items 4.1 User Mode Items 4.1.1 Common Settings (iR2030i/iR2030/iR2025i/iR2025/iR2022i/iR2018i) 0017-5938 iR2022i / iR2025 / iR2030 / iR2018i T-4-1 Item Settings Initial Function Select Initial Function: Copy*1, Send, Scan Set System Monitor Screen as initial function: On, Off*1...
  • Page 26: 3adjustment/cleaning (ir2030i/ir2030/ir2025i/ir2025/ir2022i/ir2018i)

    3 to 30 minutes; 5*1 Auto Clear Time 0 (Off) to 9 minutes, in one minute increments; 2 min.*1 *1 Indicates the default setting. 4.1.3 Adjustment/Cleaning (iR2030i/iR2030/iR2025i/iR2025/iR2022i/iR2018i) 0017-5940 iR2022i / iR2025 / iR2030 / iR2018i T-4-3 Item Settings Transfer Roller Cleaning Press [Start].
  • Page 27: 6copy Settings (ir2030i/ir2030/ir2025i/ir2025/ir2022i/ir2018i)

    UFRII LT*1, PCL5e, PCL6, FAX *1 Indicates the default setting. *2 Indicates items that appear only when the appropriate optional equipment is attached. 4.1.6 Copy Settings (iR2030i/iR2030/iR2025i/iR2025/iR2022i/iR2018i) 0017-5943 iR2022i / iR2025 / iR2030 / iR2018i T-4-6 Item Settings Image Orientation Priority...
  • Page 28: 8printer Settings (ir2030i/ir2030/ir2025i/ir2025/ir2022i/ir2018i)

    On*1, Off *1 Indicates the default setting. *2 Indicates items that appear only when the appropriate optional equipment is attached. 4.1.8 Printer Settings (iR2030i/iR2030/iR2025i/iR2025/iR2022i/iR2018i) 0017-5945 iR2022i / iR2025 / iR2030 / iR2018i T-4-8 Item Settings DEFAULT PAPERSIZE LTR*, STMT, EXECUTIV, ISO-B5, ISO-C5, COM10,...
  • Page 29: 9address Book Settings (ir2030i/ir2030/ir2025i/ir2025/ir2022i/ir2018i)

    *2 Offset and staple items appear only when the optional Finisher-U2 is attached. *3 This setting is available only if the BarDIMM function is activated. 4.1.9 Address Book Settings (iR2030i/iR2030/iR2025i/iR2025/iR2022i/iR2018i) 0017-5946 iR2022i / iR2025 / iR2030 / iR2018i T-4-9 Item Settings...
  • Page 30: 10recommended Setting Of System Management Information

    4.1.10 Recommended setting of system management information 0017-5948 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i When multiple users use the machine, it is necessary to advise each user to set the system management information. Setting ID and password of system administrator on the operation unit under (Additional functions key) > [System management setting] > [Setting of system ad- ministrator's information] has an effect of restraining the third person from falsifying information, for the ID and password are required when a user carries out an important setting of the machine.
  • Page 31: Chapter 5 Service Mode

    0017-6052 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i The items registered and set by each of these switches comprise 8-bit switches. The figure below shows which numbers are assigned to which bits. Each bit has a value of either 0 or 1.
  • Page 32: Sssw-sw04

    5.1.1.3.2 Detailed Discussions of Bit 7 0017-6056 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i Use it to enable/disable transmission of a 1080-Hz tonal signal before transmission of the CED signal. Select 'transmit' if errors occur frequently because of an echo when reception is from overseas.
  • Page 33: Sssw-sw05

    5.1.1.4.4 Detailed Discussions of Bit 4 0017-6060 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i Use it to select the time length during which low-speed signals are ignored after transmission of the CFR signal. If the condition of the line is not good and, therefore, the reception of image signals is difficult, select '1500 ms.' 5.1.1.4.5 Detailed Discussions of Bit 5...
  • Page 34: Sssw-sw13

    Time-Out Length for Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 Reception 8 min 16 min 32 min 64 min 5.1.1.7 SSSW-SW13 5.1.1.7.1 List of Functions 0017-6069 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i T-5-9 Function not used...
  • Page 35: Sssw-sw14

    5.1.1.7.2 Detailed Discussions of Bit 2 0017-6070 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i It converts "inch" into "mm" when transmitting the received image data. Scanning direction in conversion follows the Bit 2 setting of SW14.
  • Page 36: Sssw-sw28

    5.1.1.9.2 Detailed Discussions of Bit 0 0017-8528 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i Transmitted telephone number could be selected on the report indication after the transmission. If the "Initiation number" is selected, report will indicate the telephone number of the initiation side.
  • Page 37: Sssw-sw30

    5.1.1.10.6 Detailed Discussions of Bit 4 0017-6079 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i Select whether the receiver falls back during V.34 reception. If 'Prohibit' is selected, the receiver does not fall back. 5.1.1.10.7 Detailed Discussions of Bit 5...
  • Page 38: Sssw-sw34

    5.1.1.12.2 Detailed Discussions of Bit 0 0017-6084 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i Use it to specify whether B4 paper (Print) should be counted as large-size paper. If 'yes' is selected, B4 paper will be counted as large-size paper.
  • Page 39: Menu Switch Settings (menu)

    0017-6090 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i Select whether to display the waste toner full warning as a drum replacement required message or as E019 displayed on an operator call. Select 1 to display a rum replacement required message on an operator call.
  • Page 40: Numeric Parameter Settings (numeric Param.)

    Chapter 5 5.1.3 Numeric Parameter Settings (NUMERIC Param.) 5.1.3.1 Numerical Parameter Composition 0017-6099 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i T-5-18 Item Range of settings RTN transmission condition(1) 1% to 99% RTN transmission condition (2) 2 to 99 item...
  • Page 41: 010: Line Connection Identification Length

    0017-6104 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i Use it to set the time for identifying the line connection. Raise this parameter if errors occur frequently at time of communication because of the condition of the line.
  • Page 42 Chapter 5 200s: copy 300s: print 400s: copy + print 500s: scan 700s: received file print 800s: report pint 900s: transmitted scan Guide to the Table - 1:Count sheets of all sizes by one. - 2:Count sheets of the large size by two. - C:full color - Bk:black mono - L:large size (larger than A4/LTR)
  • Page 43 Chapter 5 Seri Counter type Print system Bk 1-sided L Bk 1-sided S Bk 2-sided L Bk 2-sided S Local Repo Local Repo Local Repo Local Repo coun copy print print copy print print copy print print copy print print print print print...
  • Page 44 Chapter 5 Seri Counter type Print system Bk 1-sided L Bk 1-sided S Bk 2-sided L Bk 2-sided S Local Repo Local Repo Local Repo Local Repo coun copy print print copy print print copy print print copy print print print print print...
  • Page 45: Scanner Function Settings (scanner)

    Chapter 5 5.1.4 Scanner Function Settings (SCANNER) 5.1.4.1 Setting of Bit Switch 0017-6116 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i <SCAN SW SSSW01> T-5-19 Function Not used Not used Not used Not used Outputting an Image for ADF Perpendicularity...
  • Page 46: 024:cis Scan Position During Adf Scanning

    5.1.4.3 <024:CIS scan position during ADF scanning> 0017-6118 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i This value is used when automatic scan position adjustment (TESTMODE>"2"SCAN TEST>"3"SHEET POS ADJ) fails. 5.1.4.4 <026:Distance from the standby position of CIS to the shading start point>...
  • Page 47: 032horizontal Scan Start Position Adjustment

    5.1.4.6 <032Horizontal scan start position adjustment> 0017-6121 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i Adjust the position at which horizontal scanning of a book starts. The larger the adjustment value, the narrower the top margin in the image becomes.
  • Page 48: 194: Adf Special Standard-sized Paper: Ltr Misidentification-ready

    5.1.4.18 <194: ADF special standard-sized paper: LTR misidentification-ready> 0017-6133 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i Set to use special standard-sized paper that is not otherwise identifiable to the ADF (because it is misidentified as "LTR").
  • Page 49: Printer Function Settings (printer)

    ( Y ) F-5-4 5.1.5 Printer Function Settings (PRINTER) 5.1.5.1 Service Soft Switch Settings 5.1.5.1.1 SSSW-SW05 List of Functions 0017-6141 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i T-5-20 Function not used not used not used not used...
  • Page 50 Detailed Discussions of Bit 0 0017-6144 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i Select whether to enable or disable transfer bias pressure reduction mode. Select "Enable" to avoid image defects (black spots) produced by transfer bias leaks occurring in a low-pressure region, such as one at a high altitude. This setting regulates the transfer bias to keep it from exceeding a predetermined level during printing.
  • Page 51 Detailed Discussions of Bit 0 0017-6153 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i Select whether to inhibit automatic delivery tray replacement while running jobs with an inner two-way tray mounted in position. Select "Enable" to inhibit auto- matic tray replacement.
  • Page 52: Numeric Parameter Settings (numeric Param.)

    Detailed Discussions of Bit 1 0017-8535 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i If there is no progress after shifting the target figure of the temperature adjustment using "Temperature Adjustment UP/DOWN Mode", # PRINTER> Numeric> Parameter 62, 63, cancel the 2nd face of the duplex inner limit of the fixed temperature adjustment.
  • Page 53 5.1.5.2.4 <033: Top registration adjustment (duplex unit)> 0017-6159 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i Adjust the top registration margin of paper picked from a duplex unit. The larger the adjustment value, the wider the top margin of the image becomes.
  • Page 54 5.1.5.2.17 <056: Margin adjustment at the left edge of the copy> 0017-6171 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i Adjust the margin at the left edge of the copy. Increasing the value makes the margin at the left edge larger.
  • Page 55: Setting Of Cassette (cst)

    5.1.5.2.26 <066:Temperature/ Humidity sensor fixed mode> 0017-8656 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i Changing to high-pressure environment by using the temperature/ humidity sensor. But when there is an image trouble at the point of changing the environment, fix the temperature and the humidity and do not allow the change of the high-pressure output.
  • Page 56: Registration Of Accessories (acc)

    IDs in the system management information. 5.1.8 Registration of Accessories (ACC) 5.1.8.1 Accessory Registration 0017-6178 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i The table below gives summary description of the accessories available. Item Explanation...
  • Page 57: Method Of Confirming License Option

    5.1.9.2 Method of confirming license option 0017-8538 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i Confirmation could be made whether the license option is active or not in the SOFT-ID PRM item by outputting the SPEC REPORT from the service mode.
  • Page 58: Erds Parameter Settings (e-rds)

    (9) Register the new license key to the transmitted device and confirm that the function is active. 5.1.10 eRDS Parameter Settings (E-RDS) 5.1.10.1 Settings Related to e-RDS 0017-6179 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i Settings related to e-RDS are described below. T-5-27 Item...
  • Page 59: Clearing Counters

    Manual feed tray separation pad paper pass count 150,000 5.1.11.2 Clearing Counters 0017-6181 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i - Maintenance/parts counter all clear Execute service mode > CLEAR > COUNTER to clear all maintenance/parts counters. - Counter clear on parts replacement Press the numeric keypad key 0 after displaying the counter for a part just replaced, and the counter will be cleared individually.
  • Page 60: System Dump List

    ----- F-5-7 5.1.12.3 System Dump List 0017-6187 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i - System Dump List Use it to check the history of communications, both successful and error. F-5-8 *1: TX, number of total pages transmission.
  • Page 61: Counter List

    *8: RX, procedural signal received; TX, procedural signal transmitted. 5.1.12.4 Counter List 0017-6188 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i Explanation: Maintenance/supplies counter output. (For more detailed information about the maintenance/supplies counter output, execute service mode > Display counter information > Counters.) 5.1.12.5 Error Log List...
  • Page 62 Chapter 5 07/12/2005 13:07 FAX *************************************** *** JAM/ERR LOG REPORT *************************************** [1] [2] [3] [4] [5] [6] [8] [9] [10] 01 04/12 12:17 20:03 4 0012 000026 1 A4 20 04/12 12:17 20:03 4 0012 000026 1 A4 [1] [2] [3] [4] [5] 01 04/12 12:17 15:36 3 0010 0000 000691...
  • Page 63: Spec List

    Error code (4-digit code; for a definition of the code, see the "Error Code" Chapter.) Detail code Detail code of the error code (4-digit code; for a definition of the code, see the "Error Code" Chapter.) Total counter display 5.1.12.6 Spec List 0017-6190 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i...
  • Page 64 Chapter 5 07/12/2005 13:07 FAX ***************************** *** SPEC REPORT ***************************** _ _ _ _ _ TYPE JAPAN _ _ _ _ _ LBP SPEED 25cpm _ _ _ _ _ TOTAL MEMORY 256MB _ _ _ _ _ MAIN WLaa-08-01 _ _ _ _ _ OPTION WLaa-08-01...
  • Page 65 Chapter 5 07/12/2005 13:07 FAX _ _ _ _ _ BIT 05: BW-SEND OFF / OFF _ _ _ _ _ BIT 06: CL-SEND OFF / OFF _ _ _ _ _ BIT 07: PAF OFF / OFF _ _ _ _ _ BIT 08: BDSS / OFF _ _ _ _ _...
  • Page 66: Service Label

    Chapter 5 5.1.12.7 Service Label 0017-6191 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i Enter the value given in the service label affixed to the rear cover when it has been replaced with a new one. #PRINT>#PRINT NUMERIC #SCAN>#SCAN NUMERIC...
  • Page 67: Download (download)

    5.1.13.1 Download 0017-6182 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i The following parts of this unit can be upgraded by executing download mode using the service support tool (SST) (for more information, see the "Upgrading" section):...
  • Page 68: Display Of Rom Information (rom)

    Chapter 5 5.1.16 Display of ROM Information (ROM) 5.1.16.1 ROM Display 0017-6184 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i The table below lists the items of ROM display mode that are supported. T-5-31 Item Explanation MAIN Displays the version number of the ROM (SYSTEM) mounted on the image processor PCB.
  • Page 69 Chapter 5 Numerals enclosed in parentheses denote a numeric keypad key to be pressed each. Group Subgroup Item 1 Item 2 Item 3 Explanation (4) MODEM TEST [1] - [9] (1) RELAY TEST [1] - [2] (1) RELAY TEST 1 NCU relay (and switch) ON/OFF test (2) RELAY TEST 2 230 V common NCU test...
  • Page 70: Test Mode Menu List (touch Panel Type)

    Chapter 5 Numerals enclosed in parentheses denote a numeric keypad key to be pressed each. Group Subgroup Item 1 Item 2 Item 3 Explanation (1) FUNCTION TEST G3 4800bps G3 4800 bps signal transmission test (3) 6-3 SENSOR [1] - [6] Sensor checks (1) SENSOR CHECK 0:NORMAL 1:LATCH (0) SENSOR NORMAL [0] - [2]...
  • Page 71 Chapter 5 Numerals enclosed in parentheses denote a numeric keypad key to be pressed each. Group Subgroup Item 1 Item 2 Item 3 Explanation (1) RELAY TEST [1] - [2] (1) RELAY TEST 1 NCU relay (and switch) ON/OFF test (2) RELAY TEST 2 230 V common NCU test (2) FREQ TEST [0] - [6]...
  • Page 72: D-ram Test<(1) D-ram Test

    (1) ADF ROL CLEAN Press start key 5.1.17.4 D-RAM Test<(1) D-RAM TEST> 0017-6196 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i D-RAM Test((1) D-RAM) Press the numeric keypad key 1 on the test mode menu to select the D-DRAM test.
  • Page 73: Scan Test ((2) Scan Test)

    Chapter 5 5.1.17.5 Scan Test ((2) SCAN TEST) 0017-6197 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i Scan test ((2) SCAN TEST) Press the numeric keypad key 2 on the test mode menu to select the CCD test.
  • Page 74 Chapter 5 Press '1'or '2' on the keypad on the Modem test menu to select relay test mode. Use the keypad to operate the various relays of the NCU. '2' on the keypad is used for 230V machine. Numeric keypad key 1 The input key and relay are shown below: RELAY TEST1 OFF OFF OFF OFF OFF OFF...
  • Page 75 Chapter 5 MEMO: The output level of individual signals is in keeping with the setting made in service mode. DTMF Signal Transmission Test A press on '5' on the MODEM test menu selects the DTMF signal transmission test. In the test, the following DTMF signals from the modem are transmitted using the telephone line terminal and the speaker.
  • Page 76: Function Test ((6) Function Test)

    Chapter 5 5.1.17.8 Function Test ((6) FUNCTION TEST) 0017-6203 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i Function test ((6) FUNCTION TEST) Press the numeric keypad key 6 on the test mode menu to select the function test.
  • Page 77 Chapter 5 6-3:SENOR [1] - [6] Press numeric keypad key 1. Press numeric keypad key 0. Press numeric keypad key 0. SENSOR CHECK SENSOR NORMAL CAS 0 REG 0 0:NORMAL 1:LATCH [0] - [2] DEL 0 0 MULTI 0 Select a sensor mode. CAS:Cassette 1 paper sensor (SR204): 0/Document presence, 1/Document absence 0: NORMAL REG:Registration sensor (SR209): 0/Document presence, 1/Document absence...
  • Page 78 Chapter 5 Press numeric keypad key 4. REF xxx ANT xxx |ANT - LEF| xxx REF: Toner reference voltage (A/D value) ANT: Toner antenna voltage (A/D value) ANT - LEF: Differential voltage (A/D value) Press numeric keypad key 5. BSCT on BDOC[A3 ] BDSS3-0 [of of of of]...
  • Page 79: Roller Cleaning Mode ((0) Roller Clean)

    5.1.17.9 Roller cleaning mode ((0) ROLLER CLEAN) 0017-6204 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i Roller cleaning mode ((0) ROLLER CLEAN) Press numeric keypad key 0 in test mode to select roller cleaning mode. Press numeric keypad keys 1 and 2 during this test to enter the following menus: Numeric keypad key 1 Press the start key clean the ADF pickup/feed rollers by idling.
  • Page 81: Chapter 6 Outline Of Components

    Chapter 6 Chapter 6 Outline of Components 6.1 Clutch/Solenoid 6.1.1 List of Clutches/Solenoids 0017-5994 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i <Reader Unit> The reader unit has no clutch/solenoid. <Printer Unit> Symbol Name Function CL201 Manual pickup clutch Drives the manual pickup roller.
  • Page 82 Chapter 6 <Reader Unit> Symbol Name Function M401 Reader motor Drives the carriage. Symbol Part No. Reader controller PCB Error M401 FK2-1066 J409 M401 F-6-2 <Printer Unit> Symbol Name Function Fixing motor Drives the fixing unit. M201 M203 Polygon motor Drives the laser scanner.
  • Page 83: Fan

    Chapter 6 6.3 Fan 6.3.1 List of Fans 0017-5997 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i <Reader Unit> The reader unit has no fan. <Printer Unit> T-6-1 Symbol Name Function Heat discharge fan Cools fixing unit.
  • Page 84 Chapter 6 <Reader Unit> T-6-2 Symbol Name Function SR401 CIS HP sensor Detects the CIS home position. SR402 Copyboard cover open/closed sensor (rear) Detects opening/closing of the copyboard cover. SR403 Copyboard cover open/closed sensor (front) Detects opening/closing of the copyboard cover. SR404 Original sensor 1 Detects the original size (AB or INCH/AB).
  • Page 85: 1list Of Switches

    Chapter 6 <Printer Unit> T-6-4 Symbol Name Function Fixing film speed sensor Detects the fixing film speed. SR101 Fixing delivery sensor Detects fixing delivery. SR202 No.1 delivery sensor Detects delivery. SR203 Cassette 1 paper sensor Detects presence/absence of cassette 1 paper. SR204 Waste toner full detection sensor Detects the waste toner full status.
  • Page 86: Switch

    Power supply PCB TH1,TH2 Fixing film unit J217 FM3-3654(120V) FM3-3653(230V) SR207 SR203 TH1, TH2, TP1 SR208 SR101 SR210 SR204 SR209 SR202 SR206 F-6-6 6.5 Switch 6.5.1 List of Switches 0017-5999 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i...
  • Page 87: Lamps, Heaters, And Others

    Cassette 1 size detection switch Detects the cassette 1 paper size. Symbol Part No. DC controller PCB Power supply PCB FM2-4433 FM2-4020 WC2-5332 J213 F-6-7 6.6 Lamps, Heaters, and Others 6.6.1 List of Lamps, Heaters, and Others 0017-6000 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i...
  • Page 88 Chapter 6 <Reader Unit> Symbol Name Part No. Function Prevents dew condensation on the ADF Reader heater (left) reading glass. Prevents dew condensation on the Reader heater (right) copyboard glass. F-6-8 <Printer unit> Symbol Name Function Fixing main heater Used as the main heater for fixing. Fixing sub heater Used as the sub heater for fixing.
  • Page 89: Pcbs

    Symbol Part No. Fixing film unit FM3-3654(120V) FM3-3653(230V) H1,H2 FM3-3712(100V) FM3-3714(230V) Symbol Part No. Modem PCB FH5-3543 FK2-1265 J1203 H1, H2 F-6-9 6.7 PCBs 6.7.1 List of PCBs 0017-6001 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i...
  • Page 90 Chapter 6 <Reader Unit> Symbol Name Part No. Function Reader controller PCB FM2-4792 controls the reader unit/ADF F-6-10 <Printer unit> Symbol Name Part No. Function Laser driver PCB Scanner unit controls the laser unit drive FM3-3695 BD PCB generates the BD signal Image processor PCB FM3-3320(LCD type) processes output image data for the printer unit...
  • Page 91 [10] [13] [12] [11] F-6-11 [14] [17] [15] [16] F-6-12...
  • Page 92: Chapter 7 System Construction

    Chapter 7 Chapter 7 System Construction 7.1 System Construction 7.1.1 Pickup/Delivery/Original Handling Accessories System Configuration (iR2018) 0017-9181 iR2018...
  • Page 93 Chapter 7 The configuration is as shown in the following figure: [11] [12] [10] F-7-1 Cassette Feeding Module-Q1 DADF-P2 Cassette Heater Attachment Kit-E1 Platen Cover Type J (*1) Duplex Unit-B1 (*1) Finisher-U2 [10] Power Supply Kit-Q1 Additional Finisher Tray-C1 [11] Document Tray-J1 Inner 2-way Tray-E2 [12]...
  • Page 94: Pickup/delivery/original Handling Accessories System Configuration (ir2018i)

    Chapter 7 7.1.2 Pickup/Delivery/Original Handling Accessories System Configuration (iR2018i) 0017-9182 iR2018i The configuration is as shown in the following figure: [10] F-7-2 Cassette Heater Attachment Kit-E1 Finisher-U2 Duplex Unit-B1 (*1) Additional Finisher Tray-C1 Power Supply Kit-Q1 Inner 2-way Tray-E2 Document Tray-J1 Cassette Feeding Module-P1 [10] Card Reader-E1...
  • Page 95: 3pickup/ Delivery /original Handling Accessories System Configuration

    Chapter 7 7.1.3 Pickup/ Delivery /Original Handling Accessories System Configuration (iR2022/iR2022N/iR2025/iR2030) 0017-9183 iR2025 / iR2030 / iR2022 The configuration is as shown in the following figure: [10] [11] F-7-3 Cassette Heater Attachment Kit-E1 DADF-P2 (*1) Duplex Unit-B1 (*1) Platen Cover Type J (*1)
  • Page 96 Chapter 7 7.1.4 Pickup/Delivery/Original Handling Accessories System Configuration (iR2022i/iR2022K/iR2025i/iR2030i) 0017-9187 iR2022i / iR2025 / iR2030 The configuration is as shown in the following figure: F-7-4 Duplex Unit-B1 (*1) Finisher-U2 Power Supply Kit-Q1 Additional Finisher Tray-C1 Document Tray-J1 Inner 2-way Tray-E2...
  • Page 97: 7reader Heater/cassette Heater System Configuration

    Chapter 7 7.1.5 Reader Heater/Cassette Heater System Configuration (iR2018/iR2022/iR2022N) 0017-9191 iR2018 / iR2022 The configuration is as shown in the following figure: F-7-5 Reader Heater (*1) Cassette Heater (*1) Heater PCB *1: To operate the heaters, a heater PCB is required. These parts are supplied as service parts, not the standard items.
  • Page 98 Chapter 7 7.1.6 Reader Heater/Cassette Heater System Configuration (iR2018i) 0017-9193 iR2018i The configuration is as shown in the following figure: F-7-6 Reader Heater (*1) Cassette Heater (*1) Heater PCB *1: To operate the heaters, a heater PCB is required. These parts are supplied as service parts, not the standard items.
  • Page 99: Ir2030/ir2030i)

    Chapter 7 7.1.7 Reader Heater/Cassette Heater System Configuration (iR2022K/iR2022i/iR2025/iR2025i/iR2030/iR2030i) 0017-9194 iR2022i / iR2025 / iR2030 The configuration is as shown in the following figure: F-7-7 Reader Heater (*1) Cassette Heater (*1) Heater PCB *1: To operate the heaters, a heater PCB is required. These parts are supplied as service parts, not the standard items.
  • Page 100 Chapter 7 7.1.8 Printing/Transmitting Accessories System Configuration (iR2018/ir2022/iR2022N) 0017-9196 iR2018 / iR2022 The configuration is as shown in the following figure: F-7-8 FAX Panel-A1 (*2) PCL Printer Kit-V1/W1 (*3) Barcode Printing Kit-B1 (license certificate) SUPER G3 FAX BD-AA1 (*2) UFRII LT P.Kit-V1 (*1) iR128MB EXP.RAM-E1 Serial Interface Board-A2 Serial Interface Kit-H1...
  • Page 101 Chapter 7 7.1.9 Printing/Transmitting Accessories System Configuration (iR2018i/iR2022i/iR2022K/iR2025/iR2025i/iR2030/iR2030i) 0017-9197 iR2022i / iR2025 / iR2030 / iR2018i The configuration is as shown in the following figure: F-7-9 Color SEND Kit-L1 (license certificate) (*1) UFRII LT P.Kit-V1 (*1) Barcorde Printing Kit-B1 (license certificate)
  • Page 102: Product Specifications

    Color Send Kit-L1 Barcode print function ==> Barcode Printing Kit-B1 7.2 Product Specifications 7.2.1 Product Specifications 0017-2617 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i Copyboard stream reading, fixed reading Body desktop Light source type LED array (CIS) Photosensitive medium OPC drum (30-mm dia.)
  • Page 103: Function List

    25% to 75% (humidity range) Operating environment 0.6 to 1.0 atm (atmospheric pressure) Noise iR2030 series: 69.5 dB or less iR2025 series: 67.75 dB or less iR2022 series: 66.7 dB or less iR2018 series: 65.5 dB or less Power supply rating 120/230V...
  • Page 104 Chapter 7 Paper size Single-sided Double-sided Casette feed Manual feed Casette feed Manual feed Plain paper 27.5 27.5 25.5 25.5 22.5 22.5 STMT 10.5 10.5 STMTR 27.5 27.5 LTRR 11.5 11.5 10.5 10.5 22.5 22.5 16KR Heavy paper; 81 to 105g/ 23 (-) 23 (23) 22 (-)
  • Page 105: Printing Speed (ir2025/ir2025i)

    Chapter 7 *1. Bond SP. FIX. Mode in the user mode: OFF *2. Bond SP. FIX. Mode in the user mode: ON Supplement: - The above copy speed does not change irrespective of whether paper is supplied from the upper/lower cassette, the manual feed tray, or from the cassette feeding module.
  • Page 106 Chapter 7...
  • Page 107 Chapter 7 T-7-1 Paper size Single-sided Double-sided Casette feed Manual feed Casette feed Manual feed Plain paper 23.5 23.5 25.5 25.5 22.5 22.5 STMT 10.5 10.5 STMTR 27.5 27.5 LTRR 11.5 11.5 10.5 10.5 22.5 22.5 16KR Heavy paper; 81 to 105g/ 23 (-) 23 (23) 22 (-)
  • Page 108: Printing Speed (ir2022/ir2022i/ir2022k/ir2022n))

    Chapter 7 *1. Bond SP. FIX. Mode in the user mode: OFF *2. Bond SP. FIX. Mode in the user mode: ON Supplement: - The above copy speed does not change irrespective of whether paper is supplied from the upper/lower cassette, the manual feed tray, or from the cassette feeding module.
  • Page 109 Chapter 7...
  • Page 110 T-7-2...
  • Page 111 Paper size Single-sided Double-sided Casette feed Manual feed Casette feed Manual feed Plain paper 25.5 25.5 22.5 22.5 STMT 10.5 10.5 STMTR 27.5 27.5 LTRR 11.5 11.5 10.5 10.5 22.5 22.5 16KR Heavy paper; 81 to 105g/ 23 (-) 23 (23) 22 (-) 22 (-) m2 *1...
  • Page 112 Envelope Monarch COM10 ISO-B5 ISO-C5 Postcard Postcard 11.5 Double postal card 10.5 4-plane post card 23.5 *1. Bond SP. FIX. Mode in the user mode: OFF *2. Bond SP. FIX. Mode in the user mode: ON Supplement: - The above copy speed does not change irrespective of whether paper is supplied from the upper/lower cassette, the manual feed tray, or from the cassette feeding module.
  • Page 114 T-7-3...
  • Page 115 Paper size Single-sided Double-sided Casette feed Manual feed Casette feed Manual feed Plain paper 25.5 25.5 22.5 22.5 STMT 10.5 10.5 STMTR 27.5 27.5 LTRR 11.5 11.5 10.5 10.5 22.5 22.5 16KR Heavy paper; 81 to 105g/ 23 (-) 23 (23) 22 (-) 22 (-) m2 *1...
  • Page 116 User Mode: Additional Functions > Adjust/Cleaning > Spesial Mode S > Speed Priority 1 or 2 7.3.5 Types of Paper 0017-5914 iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i Source Type Paper size...
  • Page 117: Chapter 8 Upgrading

    1. When updagrading Boot, make sure to update Boot first. 2. When updagrading the following software, make sure to update all to the same version. - System - PCL 8.1.2 Overview of Upgrade (Touch panel type) 0017-6004 iR2022i / iR2025 / iR2030 / iR2018i...
  • Page 118: Overview Of Service Support Tool (lcd Type)

    When using the SST, select "#DOWNLOAD" in the service mode to place the main unit in the download mode. (The finisher need not enter the download mode.) 8.1.4 Overview of Service Support Tool (Touch panel type) 0017-6006 iR2022i / iR2025 / iR2030 / iR2018i...
  • Page 119 Chapter 8 Main unit Image processor PCB 16MB ROM USB cable Flash ROM J303 16MB ROM PCB System software Flash ROM RS232C straight cable USB Memory Downloader Flash Memory FY9-2034 PCL printer kit-W1 32MB ROM PCB Flash ROM Finisher-U2 Finisher controller PCB Flash ROM J918 F-8-2...
  • Page 121 Aug 8 2007...

This manual is also suitable for:

Ir2025Ir2022Ir2018

Comments to this Manuals

Symbols: 0
Latest comments: