When Replacing The Standard White Plate; When Replacing The Scanning Lamp; After Replacing The Scanning Lamp - Canon ImageRunner iR8500 Series Service Manual

Chapter 14
following:
Book Mode
A: COPIER>ADJUST>ADJ-XY>ADJ-X
B: COPIER>ADJUST>ADJ-XY>ADJ-Y
A
Feeder Mode
C: COPIER>ADJUST>ADJ-Y-DF
9) Execute the following in service mode to generate a service label;
FUNCTION>MISCP> LBL-PRNT. Store the service label in the
service book case.

14.3.4 When Replacing the Standard White Plate

iR105i/iR105+ / iR9070
1) Check to be sure that the Execute/Memory lamp in the control panel
is OFF, and turn off the main power switch.
2) Disconnect the power plug from the power outlet.
The machine remains powered as long as its power plug is connected.
Be sure to disconnect the power plug from the power outlet.
3) Replace the standard white plate.
4) Assemble the machine, and connect the power plug; then, turn on the
main power switch.
5) Execute the following in service mode in sequence:
COPIER> FUNCTION> CCD> CCD-ADJ
COPIER> FUNCTION> CCD> LUT-ADJ
6) Inplement the service mode described below to the service sheet
which is to be kept in the service log book case.
COPIER> FUNCTION> MISC-P> LBL-PRNT
7) Turn off and then on the main power switch.

14.3.5 When Replacing the Standard White Plate

1) Check to be sure that the Execute/Memory lamp in the control panel
is OFF, and turn off the main power switch.
2) Disconnect the power plug from the power outlet.
The machine remains powered as long as its power plug is connected.
Be sure to disconnect the power plug from the power outlet.
14-26
B
F-14-54
C
F-14-55
0008-3974
0008-8596
3) Replace the standard white plate.
4) Assemble the machine, and connect the power plug; then, turn on the
main power switch.
5) Execute the following in service mode in sequence:
1. COPIER>FUNCTION>CCD>CCD-ADJ
2. COPIER>FUNCTION>CCD>LUT-ADJ
6) Inplement the service mode described below to the service sheet
which is to be kept in the service log book case.
- COPIER>FUNCTION>MISC-P>LBL-PRNT
7) Turn off and then on the main power switch.

14.3.6 When Replacing the Scanning Lamp

iR105i/iR105+ / iR9070
1) Check to make sure that the Execute/Memory lamp in the control
panel is OFF, and turn off the main power switch.
2) Disconnect the power plug from the power outlet.
The machine remains powered as long a the power plug is connected. Be
sure to disconnect the power plug from the power outlet without fail.
3) Replace the scanning lamp.
4) Assemble the machine, and connector the power plug to the power
outlet; then, turn on the main power switch.
5) Execute the following in service mode in sequence:
COPIER> FUNCTION> CCD> CCD-ADJ
COPIER> FUNCTION> CCD> LUT-ADJ
6) Inplement the service mode described below to the service sheet
which is to be kept in the service log book case.
COPIER> FUNCTION> MISC-P> LBL-PRNT
7) Turn off and then on the main power switch.

14.3.7 When Replacing the Scanning Lamp

1) Check to make sure that the Execute/Memory lamp in the control
panel is OFF, and turn off the main power switch.
2) Disconnect the power plug from the power outlet.
The machine remains powered as long a the power plug is connected. Be
sure to disconnect the power plug from the power outlet without fail.
3) Replace the scanning lamp.
4) Assemble the machine, and connector the power plug to the power
outlet; then, turn on the main power switch.
5) Execute the following in service mode in sequence:
1. COPIER>FUNCTION>CCD>CCD-ADJ
2. COPIER>FUNCTION>CCD>LUT-ADJ
6) Inplement the service mode described below to the service sheet
which is to be kept in the service log book case.
- COPIER>FUNCTION>MISC-P>LBL-PRNT
7) Turn off and then on the main power switch.

14.3.8 After Replacing the Scanning Lamp

/ iR8070
Execute'CCD auto adjustment'in service mode, and record the updated
CCD adjustment
data on the service label.
1. CCD Auto Adjustment
COPIER>FUNCTION>CCD>CCD-ADJ
2. CCD Adjustment Data all items under
COPIER>ADJUST>CCD
0008-3976
0008-8581
0008-8583