Attaching The Labels, Setting Paper, Checking Images/Operations, And User Mode - Canon ImageRunner iR8500 Series Service Manual

Chapter 2
9) Press the release button, and slide out the cassette 3/4.
10) Peel off the appropriate cassette size label [1] from the liner of the
size label (cassette/deck), and attach it on the paper size plate [2] of
the cassette. Put the paper size plate in place on the cassette cover.
[1]
11) Push in the cassettes into the copier.
12) Start service mode.
MEMO
Starting Service mode
- Press the Additional Function key.
- Press the '2' and '8' keys at the same time on the keypad.
- Press the Additional Function key.
Never turn off the power while the machine is in operation.
13) Make the
COPIER>FUNCTION>INSTALL>TONERS.
14) See that the following message has appeared: 'Check the Developer'.
15) Check to see that the developing assembly and the developing
assembly locking plate are correctly mounted; then, press the OK
key.
16) The machine starts to supply toner (about 10 min; progress shown
on display by count-down).
17) At the end, make the following selections to generate 2 A3 solid
black copies to ensure stable images:
18) COPIER>TEST>PG>PG_PICK.
19) Enter the number of the source of paper containing A3 paper, and
press the OK key
('3' for cassette 3, or '4' for cassette 4).
20) Make the following selections: COPIER>TEST>PG>TYPE.
21) Enter '7', and press the OK key
('7' for solid black; PG-TYPE7).
22) Press the Start key to generate a single solid black (A3) copy. Check
the output, and wait for about 5 sec; then, press the Start key once
again to generate a second copy.
23) At the end, press the Reset key twice to end service mode.
24) Make test prints, and check images.
Check to make sure that pickup from each source of paper is normal
(Make 3 test copies each from the decks and the cassettes).
- Check to make sure that there is no abnormal noise.
- Check the quality of copy images for each default ratio.
- Check to make sure that as many copies as set are made.
- Check to make sure that copying operation is normal.
- If there is a difference in density between left and right, adjust the
height of the rear of the primary charging assembly.
The first 10 copies or so may show soiled images because of toner
dropping from the drum separation claw. This symptom will disappear
as more and more copies are made.
25) Make double-sided copies, and check the operation.
26) Make user mode and service mode settings to suit the needs of the
user.
27) Press the Rest key twice to end service mode.
28) If the user tends to use thick paper or index paper or often use cover/
2-46
[2]
F-2-191
following selections:
interleaf mode or otherwise is a high copy volume user, change the
following service mode settings:
COPIER>OPTION>BODY>TEMP-TBL (Level 2)"5"(Default)->"0"
MEMO:
Starting Service Mode (Level 2)
-Press the Additional Function key.
-Press the 2 and 8 keys on the keypad at the same time.
-Press the Additional Function key.
Press the Additional Function key and the 2 key in succession.
29) Clean up the area around the copier.
30) Move the copier to its final location, and secure it in place using the
adjusters.
31) If you are installing options, do so by referring to the Installation
Procedure that comes with each option.
MEMO
For the Card Reader-D1, see "Installing the Card Reader-D1."
32) Fill out the Service Sheet.
2.2.42 Attaching the Labels, Setting Paper,
Checking Images/Operations, and User Mode
1) Check to make sure that the front deck and the cassette are free of any
packing material.
2) Remove the screw [1] from the machine.
[1]
3) Connect the grounding wire [2] to the copier using the screw [1]
removed in step 2).
0007-3512
F-2-192