Notes, Cautions, And Warnings - Chrysler 1998 Viper RT/10 Owner's Manual

S R
8W - 01 GENERAL INFORMATION 8W - 01 - 7
DESCRIPTION AND OPERATION {Continued)
C0N1ECT0R INFORMATION
C A U T I O N ; Not all c o n n e c t o r s a r e s e r v i c e d . S o m e
c o n n e c t o r s a r e s e r v i c e d o n l y with a h a r n e s s , A typ-
ical e x a m p l e might b e t h e S u p p l e m e n t a l R e s t r a i n t
S y s t e m c o n n e c t o r s . A l w a y s c h e c k p a r t s availability
before attempting a repair,
IDENTIFICATION
In-line connectors are identified by a number, as
follows:
• In-line connectors located on the e n g i n e com-
p a r t m e n t h a r n e s s are C100 series numbers.
• Connectors, located on the i n s t r u m e n t p a n e l
h a r n e s s are C200 series numbers.
• Connectors located on the body h a r n e s s are
C300 series numbers.
• J u m p e r h a r n e s s connectors are C400 series
numbers.
• G r o u n d s a n d g r o u n d connectors are identi-
fied w i t h a " G " and follow the same series number-
i n g as the in-line connector.
Component connectors are identified by the compo-
nent name instead of a number (Fig. 2 ) . M u l t i p l e
connectors on a component use a C I , C2, etc. identi-
fier (Fig. 3).
A B S
W A R N I N G
L A M P
T R A C T I O N
C O N T R O L
A C T I V E
LAMP
A
M E S S A G E
T R A C T I O N
| C E N T E R
\ CONTROL (8W-46-2)
' W A R N I N G «
Y v L M I V i r v LAMP I
, J L „
±
J L _
J ' .
sy
2 y a y
Fig. 2 Component Identification
6 ^ 0 2
BRAKE
WARNING
LAMP
I N S T R U M E N T
C L U S T E R
(8W-40-6)
6yci
Section 8W-80 shows each connector and the cir-
cuits involved w i t h that connector. The connectors
are identified using the name/number on the Dia-
gram pages.
SPLICE LOCATIONS
Splice Location charts i n Section 8W-70 show the
entire splice, and provide references to other sections
the splice serves.
Section 8W-95 contains illustrations t h a t show the
general location of the splices i n each harness. The
illustrations show the splice by number, and provide
a w r i t t e n location.
NOTES, CAUTIONS, and WARNINGS
Throughout this group additional i m p o r t a n t infor-
mation is presented i n three ways; Notes, Cautions,
and Warnings.
N O T E S are used to help describe how switches or
components operate to complete a particular circuit.
They are also used to indicate different conditions
t h a t may appear on the vehicle. For example, an
up-to and after condition.
C A U T I O N S are used to indicate information that
could prevent m a k i n g an error t h a t may damage the
vehicle.
W A R N I N G S provide information to prevent per-
sonal injury and vehicle damage. Below is a list of
general warnings that should be followed any time a
vehicle is being serviced.
W A R N I N G : A L W A Y S W E A R S A F E T Y G L A S S E S F O R
E Y E P R O T E C T I O N .
W A R N I N G : U S E S A F E T Y S T A N D S A N Y T I M E A P R O -
C E D U R E R E Q U I R E S B E I N G U N D E R A V E H I C L E .
W A R N I N G : B E S U R E T H A T T H E I G N I T I O N S W I T C H
A L W A Y S I S IN T H E O F F P O S I T I O N , U N L E S S T H E
P R O C E D U R E R E Q U I R E S IT T O B E O N .
W A R N I N G : S E T T H E P A R K I N G B R A K E W H E N
W O R K I N G O N A N Y V E H I C L E . A N A U T O M A T I C
T R A N S M I S S I O N S H O U L D B E IN P A R K . A M A N U A L
T R A N S M I S S I O N S H O U L D B E IN N E U T R A L .
Fig. 3 Connector Identification
LOCATIONS
Section 8W-90 contains connector/ground location
illustrations. The illustrations contain the connector
name (or number)/ground number and component
identification. Connector/ground location charts i n
Section 8W-90 reference the i l l u s t r a t i o n number for
components and connectors.
W A R N I N G : O P E R A T E T H E E N G I N E O N L Y IN A
W E L L - V E N T I L A T E D A R E A .
W A R N I N G : K E E P AWAY F R O M M O V I N G P A R T S
W H E N T H E E N G I N E I S R U N N I N G , E S P E C I A L L Y T H E
F A N A N D B E L T S .