SELVA MARINE Kingfish 25 Service Manual page 391

Index
Removing the power unit
(remote control model)............................7-14
Removing the power unit
(tiller handle model) ................................7-16
Removing the propeller
shaft housing assembly .................. 8-8
Removing the PTT motor..........................9-63
Removing the PTT unit .............................9-59
Removing the starter motor ......................5-22
Removing the steering arm............. 9-42
Removing the thermo sensor....................7-51
Removing the throttle link,
throttle cam, and shift cam............ 6-16
Removing the timing belt and sprocket.....7-23
Removing the upper case ......9-17
Removing the water pump ................ 8-6
Removing the wiring harness....................7-29
Replacing the oil filter..............................10-12
Replacing the timing belt.........................10-15
Replacing the valve guide.........................7-41
Reverse gear shim (T2) selection chart ....8-68
Rigging grommet description ....................3-13
Rigging information ...................................1-21
Rigging recommendations ........................3-15
Rotating part ...............................................0-1
S.
Safety while working ...................................0-1
Selecting the crankpin bearing..................7-61
Selecting the crankshaft journal bearing...7-63
Selecting the forward gear shim ...............8-26
Selecting the pinion shim ..........................8-25
Selecting the pinion shim (T3) ..................8-58
Selecting the reverse gear shim ...............8-27
Selection ...................................................3-16
Self-protection.............................................0-2
Serial number..............................................1-2
Shift link and shift rod................................9-11
Shim location .................................. 8-24
Shimming ...............................8-24
Shimming (high thrust model) ...................8-52
Shimming check sheet..............................8-53
Shimming workflow ...................................8-52
Special service tool ............................. 0-3
Special tightening torque ..........................1-21
Starboard view ............................................5-4
Starter motor ................................... 5-21
Starting ignition timing control.....................2-4
Starting system .........................................1-11
Starting the engine
(manual starter model)............................10-8
Starting unit and components ...................5-18
Steering arm .............................................9-41
i-5
,
8-39
T.
,
9-44
,
6-19
, ,
9-20 9-24
,
8-37
U.
V.
W.
,
8-57
, ,
8-25 8-57
,
0-7
,
7-32
Steering arm (high thrust model) .............. 9-43
Steering friction (tiller handle model) .......... 9-8
Swivel bracket (manual tilt model) ............ 9-50
Symbol........................................................ 0-6
System diagram..................... 2-10
Test run .................................................... 10-8
Throttle link, throttle cam,
and shift cam (remote control model) ..... 6-18
Throttle link, throttle cam,
and shift cam (tiller handle model).......... 6-15
Tightening torque........................................ 0-3
Tiller handle .........................................5-8
Tilt down operation ................................... 2-17
Tilt up operation........................................ 2-16
Top view ..................................................... 5-7
Troubleshooting procedure......................... 4-1
Troubleshooting the lower unit ................. 4-10
Troubleshooting the outboard motor .......... 4-1
Troubleshooting the power unit .................. 4-2
Troubleshooting the PTT unit ..................... 4-9
Uncrate procedure.................................... 3-10
Upper case ............................................... 9-26
Upper case (high thrust model) ................ 9-28
Upper case and mounts
(high thrust model).................................. 9-22
Upper case and mounts (L-transom) ........ 9-19
Upper case and mounts
(S-transom, for Europe).......................... 9-15
Using the digital tester .............................. 5-10
Ventilation................................................... 0-1
Water pump ................................................ 8-4
Water pump (high thrust model) ............... 8-36
When the outboard motor hits
something in the water ........................... 2-18
Wiring harness and CDI unit..................... 7-27
Working with crane ..................................... 0-2
, ,
2-11 2-12
,
9-1