SELVA MARINE Kingfish 25 Service Manual page 387

Index
A.
Abbreviation ................................................0-5
Acceleration ignition timing control .............2-5
Acceleration pump ....................................2-14
Adjusting the forward
gear shim thickness (T1).........................8-63
Adjusting the pulser coil air gap ..................7-2
Adjusting the reverse
gear shim thickness (T2).........................8-66
Adjusting the shift cable ..........................10-15
Adjusting the start-in-gear
protection cable.......................................7-11
Adjusting the throttle cable
(tiller handle model) ..................................9-6
Adjusting the throttle link rod........... 6-17
Adjusting the throttle link rod
and throttle cable ..................................10-15
Adjusting the valve clearance .....................7-3
After test run .............................................10-9
Assemble the gear pump housing ............9-70
Assembling the carburetor ........................6-13
Assembling the cylinder block...................7-63
Assembling the cylinder head ...................7-46
Assembling the drive shaft.............. 8-18
Assembling the forward gear .......... 8-18
Assembling the fuel pump...........................6-7
Assembling the lower case ............. 8-16
Assembling the manual starter ...................7-8
Assembling the oil pan and
exhaust manifold........................... 9-34
Assembling the oil seal housing...... 8-18
Assembling the
propeller shaft assembly ................. 8-9
Assembling the propeller
shaft housing assembly .................. 8-9
Assembling the PTT cylinder ....................9-75
Assembling the PTT motor .......................9-64
Assembling the starter motor ....................5-25
Assembling the steering friction ..................9-9
Assembling the swivel bracket..................9-52
Assembling the tiller handle ........................9-5
Assembling the upper case............. 9-27
Automatic decompression device
(manual starter model)..............................2-9
B.
Balancer......................................................2-9
Basic ignition timing control ........................2-4
Battery requirement .......................... 1-7
Bleeding the PTT unit ...............................9-76
Bottom cowling..........................................9-12
Bracket unit ....................................... 1-5
Bracket unit technical data........................1-20
i-1
Break-in .................................................... 10-9
C.
Camshaft and valve.................................. 7-37
Carburetor .......................................2-13
CDI unit coupler layout ............................... 5-9
Changing the engine oil.......................... 10-10
Changing the gear oil ............................. 10-12
Charging system....................................... 1-10
Charging unit and components................. 5-27
Checking the alert indicator ...................... 5-15
Checking the anode.................................. 10-9
Checking the armature (PTT motor)......... 9-63
Checking the armature (starter motor) ..... 5-24
,
Checking the battery........................10-3
6-20
Checking the brush..........................5-25
Checking the camshaft ............................. 7-45
Checking the carburetor ........................... 6-12
Checking the CDI unit............................... 5-13
Checking the charge coil .......................... 5-12
Checking the clamp bracket anode
(high thrust model).................................. 9-56
Checking the compression pressure .......... 7-1
,
Checking the connecting rod big
8-47
,
end side clearance ................................. 7-59
8-47
Checking the connecting rod
,
small end inside diameter and
8-45
big end inside diameter .......................... 7-59
Checking the cooling water passage ........ 10-9
, Checking the cooling water pilot hole ....... 10-3
9-39
,
Checking the crankpin oil clearance......... 7-60
8-47
Checking the crankshaft ........................... 7-59
, Checking the crankshaft journal
8-40
oil clearance ........................................... 7-61
,
Checking the cylinder bore ....................... 7-57
8-40
Checking the cylinder head ...................... 7-40
Checking the cylinder head anode ........... 7-46
Checking the diaphragm and valve ............ 6-7
Checking the dog clutch ....................8-9
Checking the drive shaft ..................8-16
Checking the drive shaft bushing ............. 9-30
,
Checking the electrical component........... 5-10
9-30
Checking the engine idle speed ............. 10-10
Checking the engine oil level.........10-4
Checking the engine shut-off switch
(remote control model) ........................... 5-18
Checking the engine shut-off switch
(tiller handle model) ................................ 5-17
Checking the engine
,
3-15
start button (tiller handle
model with electric starter)...................... 5-16
,
1-22
,
6-10
,
10-9
,
9-64
,
8-40
,
8-45
,
10-11