SELVA MARINE Kingfish 25 Service Manual page 389

Index
Cold and warm engine ignition
timing control.............................................2-6
Cooling system .........................................2-11
Crankcase assembly.................................1-17
Crate top cover pictograph description .......3-9
Cylinder block ...........................................7-54
Cylinder head............................................7-34
Cylinder head assembly............................1-14
D.
Dimension and Weight................................1-3
Dimensions .................................................3-2
Disassembling the carburetor ...................6-12
Disassembling the cylinder block..............7-56
Disassembling the cylinder head ..............7-39
Disassembling the drive shaft ......... 8-14
Disassembling the forward gear ..... 8-14
Disassembling the fuel pump......................6-6
Disassembling the gear pump housing.....9-69
Disassembling the lower case ........ 8-15
Disassembling the manual starter...............7-7
Disassembling the oil pan
and exhaust manifold.................... 9-34
Disassembling the
oil seal housing ............................. 8-14
Disassembling the
propeller shaft assembly ................. 8-8
Disassembling the propeller
shaft housing assembly .................. 8-8
Disassembling the PTT cylinder ...............9-74
Disassembling the PTT motor...................9-63
Disassembling the starter motor ...............5-22
Disassembling the steering friction .............9-9
Disassembling the swivel bracket .............9-52
Disassembling the tiller handle ...................9-4
Disassembling the upper case........ 9-27
Disassembly and assembly ........................0-3
Drive shaft and lower case........................8-12
Drive shaft and lower case
(high thrust model) ..................................8-42
E.
Electric shock..............................................0-1
Electrical component and
wiring harness routing...............................5-1
Electrical technical data ..............................1-7
Engine control system.................................2-1
Engine speed control ..................................2-7
Engine speed control
during low oil pressure ..............................2-7
Engine speed control during overheating ...2-7
Engine speed control
during over-revving ...................................2-7
i-3
Engine speed control system ..................... 1-9
Exhaust cover........................................... 7-49
Exterior Kingfish 25 E.ST.... ....................... 3-4
Exterior Kingfish 25 .................................... 3-5
Exterior Kingfish 25 E.ST.PT....................... 3-2
F.
Flywheel magnet and timing belt .............. 7-21
Forward gear shim (T1) selection chart .... 8-65
Front view ................................................... 5-5
Fuel and oil requirement............................. 1-6
Fuel filter assembly..................................... 6-2
Fuel hose, blowby hose,
and cooling water hose............................. 6-1
Fuel pump................................................... 6-5
,
8-44
Fuel system .....................................1-11
,
8-44
Fuel system technical data ....................... 1-11
G.
,
8-45
General feature........................................... 1-1
General periodic maintenance.................. 10-9
General tightening torque ......................... 1-24
,
9-38
H.
,
8-44
Handling of gas torch.................................. 0-2
Handling of gasoline ................................... 0-1
,
8-39
Handling of sealant..................................... 0-2
Hose routing ............................................... 6-1
,
8-39
Hot part....................................................... 0-1
How to use this manual .............................. 0-4
I.
Ignition control system................................ 2-3
Ignition timing control.................................. 2-3
,
9-30
Ignition timing control system ..................... 1-7
Ignition unit and components.................... 5-10
Installing the battery ................................. 3-15
Installing the carburetor ............................ 6-14
Installing the clamp bracket .............9-48
Installing the cylinder head ....................... 7-35
Installing the exhaust cover ...................... 7-53
Installing the flywheel magnet .................. 7-26
Installing the lower unit ....................8-21
Installing the manual starter ..................... 7-10
Installing the oil filter ................................. 7-52
Installing the oil pressure switch ............... 7-52
Installing the power unit
(remote control model) ........................... 7-17
Installing the power unit
(tiller handle model) ................................ 7-20
,
1-21
,
9-56
,
8-49